Dukane Imagepro 8755e-Rj Portable Lcd Projector Users Manual

							
5

Network Functions
When configuring or controlling the projector via a web browser, an ID and 
password are required. There are two types of IDs, Administrator IDs and User 
IDs. The following chart describes the differences between user and administrator 
IDs.
Below are the factory default settings for administrator IDs, user IDs a\
nd 
passwords.
ItemDescriptionAdministrator IDUser ID
Network InformationDisplays the projector’s current network configuration settings.√√
Network SettingsDisplays and configures network settings.√N/A
Port SettingsDisplays and configures communication port settings. √N/A
Mail SettingsDisplays and configures e-mail addressing settings.√N/A
Alert SettingsDisplays and configures failure & warning alerts.√N/A
Schedule SettingsDisplays and configures schedule settings.√N/A
Date/Time SettingsDisplays and configures the date and time settings.√N/A
Security SettingsDisplays and configures passwords and other security settings.√N/A
Projector ControlControls the projector.√√
Projector StatusDisplays and configures the current projector status.√√
Network RestartRestarts the projector’s network connection.√N/A
ItemIDPassword
Administrator IDAdministrator
User IDUser
Configuring and controlling the projector via a web browser (Continued) 
						

							
6

Settings
Settings
Refer to the following for configuring or controlling the projector via a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
)   Enter
 
[https://192.168.1.10] into the 
address bar of the web browser and 
the screen in Fig.    will be displayed.

) 
 
Enter your ID and password and click 
[Logon].
If the logon is successful either the Fig.2 or Fig.3 screen will be displayed.
3) 
 Click the desired operation or configuration item on the main menu located on 
the left-hand side of the screen (Fig. 2 or Fig. 3).
Fig.    (Logon with administrator ID)Fig. 3 (Logon with user ID)
Fig.  
						

							
7

Settings
Network Information
All screen images displayed in this manual are 
screens of a logon using an administrator ID.
Any administrator only functions will not be 
displayed when using a user ID. Refer to the 
descriptions in each table.
Displays the projector’s current network configuration settings.
ItemDescription
DHCPDisplays the DHCP configuration settings.
IP AddressDisplays the current IP address.
Subnet MaskDisplays the Subnet Mask.
Default GatewayDisplays the Default Gateway.
MAC AddressDisplays the MAC address.
Firmware DateDisplays the network firmware time stamp. This information is only displayed when logged on using an administrator ID.
Firmware VersionDisplays the network firmware version number. This information is only displayed when logged on using an administrator ID. 
						

							
8

Settings
Network Settings
Displays and configures network settings.
Click the [Apply] button to save the settings.
• The new configuration settings are activated after restarting the 
network connection. When the configuration settings are changed, you must 
restart the network connection. You can restart the network connection by 
clicking [Network Restart] on the main menu.
• If you connect the projector to an existing network, consult a netw\
ork 
administrator before setting server addresses.
NOTE
ItemDescription
IP ConfigurationConfigures network settings.
DHCP ONEnables DHCP.
DHCP OFFDisables DHCP.
IP AddressConfigures the IP address when DHCP is disabled.
Subnet MaskConfigures the Subnet Mask when DHCP is disabled.
Default GatewayConfigures the Default Gateway when DHCP is disabled.
Projector NameConfigures the Projector name.
SysLocationConfigures the location to be referred to when using SNMP.
SysContactConfigures the contact information to be referred to when using SNMP. 
						

							
9

Settings
Port Settings
Displays and configures communication port settings.
Click the [Apply] button to save the settings.
• The new configuration settings are activated after restarting the 
network connection. The network connection must be restarted when the 
configuration settings are changed. The network connection can be restarted 
using [Network Restart] on the main menu.dresses.
NOTE
ItemDescription
Network Control Port1 (Port:23)Configures command control port 1 (Port:23).
Port openClick the [Enable] check box to use port 23.
AuthenticationClick the [Enable] check box when authentication is required for this port.
Network Control Port2 (Port:9715)Configures command control port 2 (Port:9715).
Port openClick the [Enable] check box to use port 9715.
AuthenticationClick the [Enable] check box when authentication is required for this port.
Image Transfer Port (Port:9716)Configures the image transfer port (Port:9716).
Port openClick the [Enable] check box to use port 9716.
AuthenticationClick the [Enable] check box when authentication is required for this port.
SNMP PortConfigures the SNMP port.
Port openClick the [Enable] check box to use SNMP.
Trap addressConfigures the destination of the SNMP Trap in IP format.
SMTP PortConfigures the SMTP port.
Port openClick the [Enable] check box to use the e-mail function. 
						

							
10

Settings
Mail Settings
Displays and configures e-mail addressing settings.
Click the [Apply] button to save the settings.
• You can confirm whether the mail settings work correctly using the 
[Send Test Mail] button.
• If you connect the projector to an existing network, consult a netw\
ork 
administrator before setting server addresses.
NOTE
ItemDescription
Send MailClick the [Enable] check box to use the e-mail function. Configure the conditions for sending email under [Alert Settings].
SMTP Server IP AddressConfigures the address of the mail server in IP format.
Sender E-mail addressConfigures the sender e-mail address.The length of the sender e-mail address can be up to 255 alphanumeric characters.
Recipient E-mail address
Configures the e-mail address of up to five recipients. You can also specify [TO] or [CC] for each address. The length of the recipient e-mail address can be up to 255 alphanumeric characters. 
						

							


Settings
Alert Settings
Displays and configures failure & warning alerts.
ItemDescription
Cover ErrorConfigures Cover Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Fan ErrorConfigures Fan Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e- mail to be sent.The length of the text can be up to 1024 alphanumeric characters. 
						

							


Settings
Alert Settings (Continued)
ItemDescription
Lamp ErrorConfigures Lamp Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Temp ErrorConfigures Temp Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Air Flow ErrorConfigures Air Flow Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters. 
						

							
13

Settings
Alert Settings (Continued)
ItemDescription
Lamp Time ErrorConfigures Lamp Time Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Cool ErrorConfigures Cool Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Filter ErrorConfigures Filter Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters. 
						

							
4

Settings
Alert Settings (Continued)
ItemDescription
Other ErrorConfigures Other Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Schedule Execution ErrorConfigures Schedule Execution Error alert settings.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.
Lamp Time AlarmConfigures Lamp Time Alarm alert settings.
Alarm TimeConfigures the lamp time to alert.
SNMP TrapClick the [Enable] check box to enable SNMP Trap alerts for this item.
Send Mail Click the [Enable] check box to enable e-mail alerts for this item.
Mail SubjectConfigures the subject line of the e-mail to be sent.The length of the subject line can be up to 255 alphanumeric characters.
Mail TextConfigures the text of the e-mail to be sent.The length of the text can be up to 1024 alphanumeric characters.