Dukane Imagepro 8711 Lcd Projector Users Manual

							Dimension Diagram
Unit : mm



 
  

•This specifications are subject to change without notice.NOTE
SPECIFICATIONS
11
ItemSpecification
Product nameLiquid crystal projector
Liquid
crystal
panelPanel size2.5 cm (0.99 type)
Drive systemTFT active matrix
Pixels786,432 pixels (1024 horizontal x 768 vertical)
LensZoom lens F=1.7 ~ 2.4  f=30.5 ~ 45.8 mm
Lamp275 W UHB
Speaker1.0W+
1.0W (Stereo)
Power supplyAC100 ~ 120V, 4.7A / AC220 ~ 240V, 2.0A
Power consumption430W
Temperature range0 ~ 35°C (Operating)
Size380 (W) x 120 (H) x 290 (D) mm (Not including protruding parts)
Weight (mass)5.7 kg
Ports
Optional PartsLamp: DT00531    Air Filter: NJ07081* For others, consult your dealer.
RGB Input Ports
RGB ................................1
BNC (when RGB selected) 
– (R.G.B.H.V) ..................1
DVI ..................................1
VIDEO Input Ports
VIDEO IN ........................1
S-VIDEO IN ....................1
COMPONENT VIDEO 
– (C
R/PR, CB/PB, Y) ........1
BNC
(when COMPONENT selected)– (CR/PR, Y, CB/PB) ........1AUDIO Ports
AUDIO IN 1 ....................1
AUDIO IN 2 ....................1
AUDIO IN (R, L) ..............1
RGB Output Port
RGB OUT........................1
AUDIO Output Port
AUDIO OUT ....................1
CONTROL Ports
CONTROL ......................1
USB ................................1
Other PortsWIRELESS & NETWORK MODULE....1
REMOTE CONTROL ......1 
						

							12
If a problem occurs with the equipment, first refer to the        “WHAT TO DO WHEN YOU
THINK A MACHINE DEFECT HAS OCCURRED” section and run through the suggested
checks. If this does not resolve the problem contact your dealer or service company. They
will tell you what warranty condition is applied.
WARRANTY AND AFTER-SERVICE
8 
						

							1
TECHNICAL TECHNICAL
SIGNAL CONNECTOR PIN ASSIGNMENT
RGB IN [1]/[2]
RGB OUT
D-sub 15-pin Shrink Mini Din 4-pinS-VIDEO
Mini Din 4-pin
Pin NoSignal
1
Color:
0.286Vp-p (NTSC, burst signal),
75Ωterminator
0.3Vp-p (PAL/SECAM, burst signal),
75Ωterminator
2Brightness:
1.0Vp-p, 75Ωterminator
3Ground
4Ground
signalTerminalSpecification
RGB signal
input
RGB
Video: RGB separate, Analog, 0.7Vp-p, 75Ωterminator (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
BNC (RGB)
(R,G,B,H,V)Video: RGB separate, Analog 0.7Vp-p, 75Ωterminator (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
BNC connector x 5
DVITMDS, DC 150-1200 mV/AC 1.56 Vp-p, TTL Level (Positive/Negative)DVI connectorAUDIO IN 1200mVrms, 57Ω(max. 3.0Vp-p)
Stereo mini jackAUDIO IN 2
Video signal
input
VIDEO IN1.0Vp-p, 75Ωterminator, RCA jack
S-VIDEO IN
Brightness signal: 1.0Vp-p, 75Ωterminator
Color signal: 0.286Vp-p (NTSC, burst signal),75Ωterminator
Color signal: 0.300Vp-p (PAL/SECAM, burst signal),75Ωterminator  
Mini DIN 4-pin jack
COMPONENT VIDEO(CR/PR, CB/PB, Y)Y signal: 1.0 Vp-p, 75 Ωterminator 
CR/PRsignal: 0.7 Vp-p, 75 Ωterminator
CB/PBsignal: 0.7 Vp-p, 75 Ωterminator
RCA jack x 3 (BNC connector x 5)BNC (COMPONENT)
(CR/PR, CB/PB, Y)
AUDIO INRL200mVrms, 50 kΩ(max. 3.0Vp-p)
RCA jack
Signal outputRGB OUT
Video: RGB separate, Analog 0.7Vp-p, 75Ω(positive)
Sync.: H,V separate, TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
AUDIO OUT200mV(rms), output impedance 1kΩ(max. 3.0Vp-p)
Stereo mini jack
Control
functionsCONTROLD-sub 15pin shrink plug
USBUSB jack (B type)
Pin NoSignalPin NoSignal
1Video input Red9-
2Video input Green10Ground
3Video input Blue11-
4-
12
RGB IN [1]: SDA (DDC)
5GroundRGB IN [2]:        -
6Ground RedRGB OUT :        -
7Ground Green13H. sync./ Composite sync.
8Ground Blue14Vertical sync
15
RGB IN [1]: SCL (DDC)
RGB IN [2]:        -
RGB OUT :        - 
						

							2
Resolution 
H × ×
VfH (kHz)fV (Hz)RatingSignal modeDisplay mode
CP-X880CP-X885
720 ×40037.985.0VESATEXTZoom inZoom in
640 ×48031.559.9VESAVGA (60Hz)Zoom inZoom in
640 ×48035.066.7Mac13modeZoom inZoom in
640 ×48037.972.8VESAVGA (72Hz)Zoom inZoom in
640 ×48037.575.0VESAVGA (75Hz)Zoom inZoom in
640 ×48043.385.0VESAVGA (85Hz)Zoom inZoom in
800 ×60035.256.3VESASVGA (56Hz)Zoom in
800 ×60037.960.3VESASVGA (60Hz)Zoom in
800 ×60048.172.2VESASVGA (72Hz)Zoom in
800 ×60046.975.0VESASVGA (75Hz)Zoom in
800 ×60053.785.1VESASVGA (85Hz)Zoom in
832 ×62449.774.5Mac16modeZoom outZoom in
1024 ×76848.460.0VESAXGA (60Hz)Zoom out
1024 ×76856.570.1VESAXGA (70Hz)Zoom out
1024 ×76860.075.0VESAXGA (75Hz)Zoom out
1024 ×76868.785.0VESAXGA (85Hz)Zoom out
1152 ×86467.575.0VESASXGA (75Hz)Zoom outZoom out
1280 ×96060.060.0VESASXGA (60Hz)Zoom outZoom out
1280 ×102464.060.0VESASXGA (60Hz)Zoom outZoom out
1280 ×102480.075.0VESASXGA (75Hz)Zoom outZoom out
1280 ×102491.285.0VESASXGA (85Hz)Zoom outZoom out
1600 ×120075.060.0VESAUXGA (60Hz)Zoom outZoom out
EXAMPLE OF COMPUTER SIGNAL
•Some computers may have multiple display screen modes. Use of some
of these modes will not be possible with this projector.
• Be sure to check jack type, signal level, timing and resolution before connecting this
projector to a computer.
• Depending on the input signal, full-size display may not be possible in some cases.
Refer to the number of display pixels above.
• Although the projector can display signals (except DVI input) with resolution up to
UXGA (1,600 x 1,200), the signal will be converted to the projector’s panel resolution
before being displayed. The best display performance will be achieved if the
resolutions of the input signal and projector panel are identical.
• The image may not be displayed correctly when the input sync. signal is “Composite
Sync.” or “Sync. on G”.
• UXGA (1,600 x 1,200) signals cannot be displayed with DVI input.NOTE 
						

							3
The following signals are used for the initial settings.
The signal timing of some computer models may be different. In such case, refer to
adjust the V.POSIT and H.POSIT of the menu.
DATA
HSYNCDATA
VSYNCDisplay interval c
Back porch b
Sync aFront porch d
Display interval c
Back porch b
Sync aFront porch d
Computer /
SignalHorizontal signal timing (µs)
abcd
TEXT2.03.020.31.0
VGA (60Hz)3.81.925.40.6
Mac 13mode2.13.221.22.1
VGA (72Hz)1.33.820.31.0
VGA (75Hz)2.03.820.30.5
VGA (85Hz)1.62.217.81.6
SVGA (56Hz)2.03.622.20.7
SVGA (60Hz)3.22.220.01.0
SVGA (72Hz)2.41.316.01.1
SVGA (75Hz)1.63.216.20.3
SVGA (85Hz)1.12.714.20.6
Mac 16mode1.13.914.50.6
XGA (60Hz)2.12.515.80.4
XGA (70Hz)1.81.913.70.3
XGA (75Hz)1.22.213.00.2
XGA (85Hz)1.02.210.80.5
1152×864 (75Hz)1.22.410.70.6
1280×960 (60Hz)1.02.911.90.9
1280×1024 (60Hz)1.02.311.90.4
1280×1024 (75Hz)1.11.89.50.2
1280×1024 (85Hz)1.01.48.10.4
1600×1200 (60Hz)1.21.99.90.4
Computer /
SignalVertical signal timimg (lines)
abcd
TEXT3424001
VGA (60Hz)23348010
Mac 13mode3394803
VGA (72Hz)3284809
VGA (75Hz)3164801
VGA (85Hz)3254801
SVGA (56Hz)2226001
SVGA (60Hz)4236001
SVGA (72Hz)62360037
SVGA (75Hz)3216001
SVGA (85Hz)3276001
Mac 16mode3396241
XGA (60Hz)6297683
XGA (70Hz)6297683
XGA (75Hz)3287681
XGA (85Hz)3367681
1152×864 (75Hz)3328641
1280×960 (60Hz)3369601
1280×1024 (60Hz)33810241
1280×1024 (75Hz)33710242
1280×1024 (85Hz)34410241
1600×1200 (60Hz)34612001
INITIAL SET SIGNALS 
						

							4
123
4
5
6
78
910
11 12
13
14
15
CONNECTION TO THE MOUSE CONTROL
1
2
3
4
1
2
3
4
+5V
—
DATA
+DATA
GND
+5V
—
DATA
+DATA
GND1
234
2
1
3
4
USB jack 
(B type)
USB jack 
(A type)Projector
USB cable
Computer
ADB Mouse
21
43
65
21
43
87
109
1211
1413
15
RTS
GND+5VADB
GND+5V (
POWER ON)
D ATA
2143
Mouse jack 
Mini DIN 4-pin Projector
Computer
CONTROL Terminal
D-sub 15-pin shrink jack
Serial Mouse
21
43
65
21
43
65
87
10987
9
1211
1413
15
RICD
RD
TD
DTR
GND
DSR
CTS
RTS RTS
GND SEL0
TD
2143
6
5
897
Mouse jack 
D-sub 9-pin Projector
Computer
123
4
5
6
78
910
11 12 13
14
15
CONTROL Terminal
D-sub 15-pin shrink jack
USB Mouse
PS/2 Mouse
21
43
65
21
43
65
87
109
1211
1413
15
CLK
D ATA
SEL0
RTS
GND+5VD ATA
GND
+5V
CLK
214365
Mouse jack 
Mini DIN 6-pin Projector
Computer
123
4
5
6
78
910
11 12 13
14
15
CONTROL Terminal
D-sub 15-pin shrink jack 
						

							5
(1) Turn off the projector and computer power supplies, and connect with the RS-232C
adapter via the RS-232C cable.
(2) Turn on the computer power supply and after the computer has started up, turn on the
projector power supply.
Control jack
D-sub 15-pin shrink jack123456789101112131415
RD
TD GND SELO
RTS
123456789
CD
RD
TD
DTR
GND
DSR
RTS
DTS
RI
12345
67
89
RS-232C jack 
D-sub 9-pin Projector Computer
Communications setting
19200bps,  8N1
1 Protocol
Consist of header (7 bytes) + command data (6 bytes).
2 Header
BE + EF + 03 + 06 + 00 + CRC_low + CRC_high
CRC_low : Lower byte of CRC flag for command data.
CRC_high : Upper byte of CRC flag for command data.
3 Command data
byte_0byte_1byte_2byte_3byte_4byte_5
ActionTypeSetting code
lowhighlowhighlowhigh
Command data chart
Action (byte_0 - 1)
ActionClassificationContent
1SETChange setting to desired value.
2GETRead projector internal setup value.
4INCREMENTIncrement setup value by 1.
5DECREMENTDecrement setup value by 1.
6EXECUTERun a command.
RS-232C COMMUNICATION
RS-232C adapter 
						

							6Requesting projector status (Get command)
(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)
+‘00H’+‘00H’) from the computer to the projector.
(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
Changing the projector settings (Set command)
(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) +
setting code (2 bytes)) from the computer to the projector.
(2) The projector changes the setting based on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Using the projector default settings (Reset Command)
(1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+
type (2 bytes) +‘00H’+‘00H’) to the projector.
(2) The projector changes the specified setting to the default value.
(3) The projector returns the response code ‘06H’ to the computer.
Increasing the projector setting value (Increment command)
(1) The computer sends the increment code  Header + Command data (‘04H’+‘00H’+
type (2 bytes) +‘00H’+‘00H’) to the projector.
(2) The projector in creases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Decreasing the projector setting value (Decrement command)
(1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+
type (2 bytes) +‘00H’ + ‘00H’) to the projector.
(2) The projector decreases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
When a command sent by the projector cannot be understood by the computer
When the command sent by the projector cannot be understood, the error command ‘15H’ is
returned by the computer. Some times, the projector ignores RS-232C commands during
other works. If the error command ‘15H’ is returned, please send the same command again.
When data sent by the projector cannot be practice
When the command sent by the projector cannot be practiced, the the error code ‘1cH’
+‘xxxxH’ is returned.
When the data length is greater than indicated by the data length code, the projector will
ignore the excess data code.
Conversely, when the data length is shorter than indicated by the data length code, an
error code will be returned to the projector.
RS-232C COMMUNICATION (continued)
•Operation cannot be guaranteed when the projector receives an
undefined command or data.
• 
Provide an interval of at least 40ms between the response code and any other code.
• The projector outputs test data when the power supply is switched ON, and when the
lamp is lit. Ignore this data.
• Commands are not accepted during warm-up.
NOTE 
						

							7
Command data chart
NamesOperation typeHeaderCommand data
CRCActionTypeSetting code
Blank ColorSet
BlueBE  EF0306  00CB  D301  0000  3003  00
WhiteBE  EF0306  006B  D001  0000  3005  00
BlackBE  EF0306  009B  D001  0000  3006  00
MyScreenBE  EF0306  00FB  CA01  0000  3020  00
ORIGNALBE  EF0306  00FB  E201  0000  3040  00
GetBE  EF0306  0008  D302  0000  3000  00
MirrorSet
NormalBE  EF0306  00C7  D201  0001  3000  00
H InverseBE  EF0306  0057  D301  0001  3001  00
V lnverseBE  EF0306  00A7  D301  0001  3002  00
H&V InverseBE  EF0306  0037  D201  0001  3003  00
GetBE  EF0306  00F4  D202  0001  3000  00
FreezeSetNormalBE  EF0306  0083  D201  0002  3000  00
FreezeBE  EF0306  0013  D301  0002  3001  00
GetBE  EF0306  00B0  D202  0002  3000  00
StartupSet
ORIGNALBE  EF0306  000B  D201  0004  3000  00
OFFBE  EF0306  009B  D301  0004  3001  00
MyScreenBE  EF0306  00CB  CB01  0004  3020  00
GetBE  EF0306  0038  D202  0004  3000  00
LanguageSet
EnglishBE  EF0306  00F7  D301  0005  3000  00
FrançaisBE  EF0306  0067  D201  0005  3001  00
DeutschBE  EF0306  0097  D201  0005  3002  00
EspañolBE  EF0306  0007  D301  0005  3003  00
ItalianoBE  EF0306  0037  D101  0005  3004  00
NorskBE  EF0306  00A7  D001  0005  3005  00
NederlandsBE  EF0306  0057  D001  0005  3006  00
PortuguêsBE  EF0306  00C7  D101  0005  3007  00
BE  EF0306  0037  D401  0005  3008  00
BE  EF0306  00A7  D501  0005  3009  00
BE  EF0306  0057  D501  0005  300A  00
GetBE  EF0306  00C4  D302  0005  3000  00
Magnify
GetBE  EF0306  007C  D202  0007  3000  00
IncrementBE  EF0306  001A  D204  0007  3000  00
DecrementBE  EF0306  00CB  D305  0007  3000  00
Auto off
GetBE  EF0306  0008  8602  0010  3100  00
IncrementBE  EF0306  006E  8604  0010  3100  00
DecrementBE  EF0306  00BF  8705  0010  3100  00
Brightness ResetExecuteBE  EF0306  0058  D306  0000  7000  00
Contrast ResetExecuteBE  EF0306  00A4  D206  0001  7000  00
V.Position ResetExecuteBE  EF0306  00E0  D206  0002  7000  00 
						

							8
Command data chart (continued)
NamesOperation typeHeaderCommand data
CRCActionTypeSetting code
H.Position ResetExecuteBE  EF0306  00IC  D306  0003  7000  00
H.Size ResetExecuteBE  EF0306  0068  D206  0004  7000  00
Color Balance 
R ResetExecuteBE  EF0306  0094  D306  0005  7000  00
Color Balance 
B ResetExecuteBE  EF0306  00D0  D306  0006  7000  00
Sharpness ResetExecuteBE  EF0306  00C4  D006  0009  7000  00
Color ResetExecuteBE  EF0306  0080  D006  000A  7000  00
Tint ResetExecuteBE  EF0306  007C  D106  000B  7000  00
Keystone_V ResetExecuteBE  EF0306  0008  D006  000C  7000  00
Keystone_H ResetExecuteBE  EF0306  0098  D806  0020  7000  00
Auto AdjustExecuteBE  EF0306  0091  D006  000A  2000  00Auto Keystone_VExecuteBE  EF0306  00E5  D106  000D  2000  00Lamp Time ResetExecuteBE  EF0306  0058  DC06  0030  7000  00Filter Time ResetExecuteBE  EF0306  0098  C606  0040  7000  00
Blank on/offSetoffBE  EF0306  00FB  D801  0020  3000  00onBE  EF0306  006B  D901  0020  3001  00GetBE  EF0306  00C8  D802  0020  3000  00
Error StatusGet
BE  EF0306  00D9  D802  0020  6000  00
(Example of Return)
00  00         01  00                 02  00             03  00
(Normal)     (Cover-error)      (Fan-error)      (Lamp-error)
04  00          05  00              06  00                  07  00          08  00
(Temp-error)   (Air flow-error)     (Lamp-Time-over)     (Cool-error)     (Filter-Error)
PowerSetOFFBE  EF0306  002A  D301  0000  6000  00
ONBE  EF0306  00BA  D201  0000  6001  00
GetBE  EF0306  0019  D302  0000  6000  00
Input SourceSet
RGBBE  EF0306  00FE  D201  0000  2000  00
RGB)BE  EF0306  003E  D001  0000  2004  00VideoBE  EF0306  006E  D301  0000  2001  00S-VideoBE  EF0306  009E  D301  0000  2002  00ComponentBE  EF0306  00AE  D101  0000  2005  00
DVIBE  EF0306  000E  D201  0000  2003  00
BNC (Component)BE  EF0306  005E  D101  0000  2006  00
GetBE  EF0306  00CD  D202  0000  2000  00
VolumeGetBE  EF0306  0031  D302  0001  2000  00
IncrementBE  EF0306  0057  D304  0001  2000  00DecrementBE  EF0306  0086  D205  0001  2000  00
MuteSetNormalBE  EF0306  0046  D301  0002  2000  00MuteBE  EF0306  00D6  D201  0002  2001  00GetBE  EF0306  0075  D302  0002  2000  00
BrightnessGetBE  EF0306  0089  D202  0003  2000  00IncrementBE  EF0306  00EF  D204  0003  2000  00DecrementBE  EF0306  003E  D305  0003  2000  00
Contrast
GetBE  EF0306  00FD  D302  0004  2000  00IncrementBE  EF0306  009B  D304  0004  2000  00
DecrementBE  EF0306  004A  D205  0004  2000  00
Color Balance R
GetBE  EF0306  0001  D202  0005  2000  00
IncrementBE  EF0306  0067  D204  0005  2000  00
DecrementBE  EF0306  00B6  D305  0005  2000  00