Dukane Imagepro 8711 Lcd Projector Users Manual

							1
LCD Projector 28A8711
USERS MANUAL  
USERS MANUAL  Vol.2 (Extended)
Thank you for purchasing this projector.
• The information in this manual is subject to change without notice.\
• The manufacturer assumes no responsibility for any errors that may \
appear in this manual  
• The reproduction, transmission or use of this document or contents is no\
t permitted without express written authority.
TRADEMARK ACKNOWLEDGEMENT :
• PS/2, VGA and XGA are registered trademarks of the International Bu\
siness Machines Corporation.
• Apple, Mac and ADB are registered trademarks of Apple Computer, Inc\
.
• VESA and SVGA are trademarks of the Video Electronics Standard Asso\
ciation.
• Windows is a registered trademark of Microsoft Corporation.
• All other trademarks are the property of their respective owners.
NOTE
WARNING• Please read the accompanying manual “SAFETY
INSTRUCTIONS” and this “USERS MANUAL” thoroughly to ensure cor\
rect
usage through understanding. After reading, store this instruction manua\
l in a 
safe place for future reference.
Page
MULTIFUNCTIONAL SETTINGS ........................................................................\
2 
WHAT TO DO WHEN YOU  THINK A MACHINE DEFECT HAS OCCURRED ......8
SPECIFICATIONS ........................................................................\
.....................11 
WARRANTY AND AFTER-SERVICE ................................................................12
........................................................................\
...............
For TECHNICAL see the end of this manual.
CONTENTS 
						

							MAIN Menu
ItemDescription
BRIGHT Adjust Brightness:Light Dark
CONTRASTAdjust Contrast:Strong Weak
ASPECT
Select Aspect Ratio:
At RGB Input or Hi-Vision 1125i(1035i/1080i)/750p of COMPONENT VIDEO
Input:
4:3 
16:9
At VIDEO Input, S-VIDEO Input or 525i/525p/625i of COMPONENT VIDEO Input:4:3 16:9 SMALL
• The SMALL picture may not be displayed correctly with certain input signals.
PICT.POSIT.Select Picture Position (for 16:9/SMALL Picture):
TOP CENTER BOTTOM
GAMMASelect Gamma Mode:
NORMAL CINEMA DYNAMIC
MIRRORSelect Mirror Status:
NORMAL H:INVERT V:INVERT H&V:INVERT
LANGUAGE
Select Menu Language:
ENGLISH 
FRANÇAIS DEUTSCH ESPAÑOL 
ITALIANO NORSK NEDERLANDS 
POTUGUÊS 
MULTIFUNCTIONAL SETTINGS
This device has 8 separate menus: MAIN, PICTURE-1, PICTURE-2, INPUT,
AUTO, SCREEN, OPTION, WIRELESS. Each of these menus is operated using
the same methods. The basic operations of these menus are as follows.
With the MAIN menu, the seven items shown in the Table below can be
performed.
Perform each operation in accordance with the instructions in the Table.
Menu screen display :Press the MENUbutton.
Menu selection :Use the lever switch 
to select a menu name, then press the
or ENTER button.
Item selection :Use the lever switch 
to select an item, then press the  or
ENTER button.
Return menu to last previous screen:Press the  button or the ESC button.
Execution of settings and/or adjustments:Perform the operation using the lever switch.
(For further details, read the explanation for each separate menu.)
Initialization of settings and/or adjustments:During operation, press the RESET button.
(Functions that are executed at the same time
as a selection, including H PHASE, LANGUAGE
selection, and ADJUST, will not be reset.)
End menu operations :Press the MENU button, or do not perform any operation for
several seconds.
MAIN Menu
2
Example : MAIN Menu
(BRIGHT)
MENU
: SELECT
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
WIRELESSBRIGHT
CONTRAST
ASPECT
PICT. POSIT.
GAMMA
MIRROR
LANGUAGE
12 
						

							PICTURE-1 Menu
PICTURE-2 Menu
With the PICTURE-1 menu, the five items shown in the Table
below can be performed.
Perform each operation in accordance with the instructions in the
Table.
With the PICTURE-2 menu, the five items shown in the Table
below can be performed.
Perform each operation in accordance with the instructions in the
Table.
ItemDescription
COLOR BAL R Adjust Red Color Balance:Dark Light
COLOR BAL BAdjust Blue Color Balance:Dark Light
SHARPNESSAdjust Sharpness (for VIDEO/S-VIDEO):Clear Soft
COLORAdjust COLOR (for VIDEO/S-VIDEO/COMPONENT VIDEO):
Dark 
Light 
TINTAdjust Tint (for VIDEO/S-VIDEO):Green Red
PICTURE-1 Menu
ItemDescription
V POSITION Adjust Vertical Position (for RGB):Up Down
H POSITIONAdjust Horizontal Position (for RGB):Left Right
H PHASE
Adjust Horizontal Phase (for RGB/COMPONENT VIDEO):
Right 
Left
• Adjust to eliminate flicker.
H SIZEAdjust Horizontal Size (for RGB):Large Small
• If the horizontal size adjustment is excessive, the image may not be displayed
correctly. In such a case, initialize H SIZE with the RESET button.
OVER SCAN
Select Over-scan Ratio (for VIDEO/S-VIDEO/COMPONENT VIDEO):
LARGE 
MIDDLE SMALL
• If you select LARGE, you may note streaking on the top and bottom of the
screen, or flicker. If this is irritating, we suggest you select SMALL.
3 PICTURE-2 Menu
Example : PICTURE1 Menu(COLOR BAL R)
Example : PICTURE2 Menu(V POSITION)
MENU
: SELECT
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
WIRELESSCOLOR BAL R
COLOR BAL B
SHARPNESS
COLOR
TINT
12
MENU
: SELECT
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
WIRELESSV POSITION
H POSITION
H PHASE
H SIZE
OVER SCAN
12 
						

							MULTIFUNCTIONAL SETTINGS (continued)
INPUT Menu
The three Input menu items listed in the table below can be manipulated. For
RGB input, the reception signal’s horizontal and vertical frequency is displayed
on the initial menu screen. Use the table below as a guide for operation.
4
Example : INPUT Menu
(BNC)
MENU
: SELECT
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
WIRELESSBNC
VIDEO
HDTV
SYNC ON G
P. IN P. INPUT
P. IN P. POSITRGBCOMPONENT
ItemDescription
BNC
BNC Pin (R/CR/PR, G/Y, B/CB/PB, H, V) function selection:
BNC (RGB) 
BNC (COMPONENT)
(R) (G) (B) (H) (V)           (C
R/PR) (Y) (CB/PB) ( - ) ( - )
(Pins for RGB)                (Pins for COMPONENT)
Selecting BNC (RGB) allows the 5 RGB2 pins (R/CR/PR, G/Y, B/CB/PB, H, V) to be
used as RGB signal BNC input as-is.
Selecting BNC (COMPONENT) allows the 3 leftmost RGB2 pins (R/C
R/PR, G/Y,
B/C
B/PB) to be used as the COMPONENT VIDEO input CR/PR, Y, and CB/PBpins.
VIDEO
Select Mode of Signal Type (for VIDEO/S-VIDEO):
AUTO 
NTSC PAL SECAM NTSC4.43 
M-PAL N-PAL
When AUTO is selected, the video/ S-video input function under ADJUST (       are enabled, and is
executed simultaneously so that the optimum signal mode is selected from among the modes listed above.
Use this function if the image becomes unstable with VIDEO/S-VIDEO. (e.g. The image becomes irregular, or lacks color.)
• AUTO mode may not function correctly with a PAL60 signal and certain other signals.
• The AUTO mode operation requires approximately 10 seconds.
• For COMPONENT VIDEO, the signal type is identified automatically even if
this function is inactive. For a HDTV signal, refer to the item HDTV below.
HDTVSelect HDTV Signal Mode: 1080i 1035i
• 
If the selected HDTV mode is incompatible with the input signal, the picture may be distorted.
SYNC ON G
On/Off SYNC ON G Mode: TURN ON TURN OFF
Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode
allows reception of SYNC on G.
• In the SYNC ON G mode, the picture may be distorted with certain input
signals. In such a case, remove the signal connector so that no signal is
received and turn SYNC ON G off, and then reconnect the signal.
P. IN P. INPUTP. IN P. screen (*) input signal selection:VIDEO S-VIDEO
Selects the signal displayed on the P. IN P. subscreen.
P. IN P. POSIT
P. IN P. screen (*) display position selection:
Selects the position at which the P. IN P. subscreen is displayed.
INPUT Menu
(*) The P. IN P. (picture-in-picture) function displays the video signal image in a subscreen (P. IN P. screen) on
top of the screen on which the RGB signal image is being displayed. (See “Displaying Child Window” Vol.1
.)
5
24 
						

							5
AUTO Menu
With the AUTO menu, the four items shown in the Table below can
be performed.
Please perform each operation in accordance with the instructions
in the Table.
ItemDescription
ADJUST
Auto Adjust (for RGB):Automatically adjusts H POSITION, V POSITION, H
PHASE, and H SIZE. Use this function with the maximum window size.
Auto Adjust (for VIDEO/S-VIDEO):This function automatically selects the
appropriate signal mode depending on input signals. This is only performed if
AUTO is selected on the VIDEO menu item (       ) of the INPUT menu.
• This function may not be available with a PAL60 signal and certain other
signals.
• The AUTO mode operation requires approximately 10 seconds.
• 
For COMPONENT VIDEO, the signal type is identified automatically even if this
function is inactive. For more information on HDTV signals, see HDTV. (       )
KEYSTONE 
Automatic keystone distortion correction:
You can automatically correct vertical keystone distortion corresponding to the
angle (forward/backward tilt) at which the unit is set up.
• If the projection screen is inclined, or if the projector is angled downwards, it
may not be possible to make the correct adjustment when V: INVERT or H&V:
INVERT is selected under the MIRROR item of the MAIN menu.
• When the zoom adjustment is set to the TELE side, automatic correction may
be excessive. The automatic correction function should be used with zoom
set to WIDE whenever possible.
POWER OFF
Adjust POWER OFF Time: 
Long (MAX. 99 min.) Short (Min. 1 min.) (DISABLE: 0 min.)
If the time set here passes without valid signal input (there is no signal input, or
signal input is out of specifications), the standby mode is set (see TURNING
ON THE POWER Vol.1        ). This function is inactive when DISABLE (0 min.) is
selected.
ONE TOUCH 
Enabling/disabling the KEYSTONE  function using the ONE TOUCH 
button:
TURN ON 
TURN OFF
Pressing the ONE TOUCH button will automatically retrieve pictures and
automatically adjust the screen (see “ADJUSTING SCREEN WITH ONE-
TOUCH” 
Vol.1), and you can also set the function to execute KEYSTONE
(see above in this table) simultaneously when pressed. KEYSTONE will be
executed if TURN ON is selected.
Example : AUTO Menu
(ADJUST)
AUTO Menu
MENU
: SELECT
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
WIRELESSADJUST
KEYSTONE
POWER OFF
ONE TOUCHEXECUTE
4
4
15
23 
						

							MULTIFUNCTIONAL SETTINGS (continued)
6
SCREEN Menu
With the SCREEN menu, the five items shown in the Table below can be performed.
Please perform each operation in accordance with the instructions in the Table.
SCREEN Menu
ItemDescription
BLANK
Selection of BLANK Screen:MyScreen ORIGINAL .. . . ..The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen
has been erased (i.e., made to vanish) by manipulating the BLANK button (please refer to the
“Temporarily Blanking the Screen” section of the separate booklet, Vol. 1 (Basic)). 
MyScreen:Using the MyScreen category (see this Table, below), one can register a desired screen
(or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen.
ORIGINAL:Existing standard screens. Please make confirmation using the actual screen(s).Option screens:Various colored non-patterned (plain) screens displayed within the Menus.•The MyScreen and the ORIGINAL Screen will each change to a non-patterned (plain) black color
screen several minutes after being displayed.
START UP
Selection of START UP Screen:MyScreen ORIGINAL TURN OFFThe START UP Screen may be voluntarily selected. The START UP Screen is displayed when
no signal has been inputted, or when spec signals are being inputted.
MyScreen:Using the MyScreen category (see this Table, below), one can register a desired screen
(or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen.
ORIGINAL:Existing standard screens. Please make confirmation using the actual screen(s).TURN OFF:A non-patterned (plain) blue color screen.•The MyScreen and ORIGINAL screens will switch to the BLANK screen (see above in this
table) a few minutes after being displayed. If the BLANK screen is the MyScreen or
ORIGINAL screen, it will turn immediately to a solid black screen.
MyScreen
Registration of MyScreen: When this item is executed, the MyScreen Menu for registration of MyScreen for the BLANK Screen
and the START UP Screen is displayed. When operations are performed in accordance with this Menu,
one can “cut” and register desired screens from among the received images within the display.
1. 
After the “Do you start capturing this picture?” message has been displayed, pressing the ESC (or
RESET) button interrupts execution of the MyScreen. When the ENTER button is pressed, the picture
becomes static (no longer moves), and a frame for picture cutting, as well as the message that follows
below, appear. Please press the button when the screen you want to register is currently being displayed.
2. When the “Move the capture area as you want.” message has been displayed, pressing the ESC (or RESET)
button will eliminate the static state of the picture, and operations can be performed again from operation 1.
The frame can be moved using the buttons. After designating the screen you
want to register, pressing the ENTER button will initiate screen registration. The registration
process takes approximately 1 minute to complete.
3. When the registration has been completed, the screen of the registered MyScreen, plus the
message, “MyScreen registration is finished,” will be displayed for several seconds, after which
the operation is terminated.
MyScreen SizeSelection of MyScreen display size:  x1 FULL
MyScreen LockInvalidation of MyScreen registration function:  TURN ON TURN OFF
When TURN ON is selected, the MyScreen category (see this Table, above) cannot be executed; in
this way, one can prohibit rewrites (“writeovers”) of the MyScreen.
Example : SCREEN Menu(BLANK)
MENU
: SELECT
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
WIRELESSBLANK
START UP
MyScreen
MyScreen Size
MyScreen LockMyScreenORIGINAL 
						

							7
OPTION Menu
With the OPTION menu, the five items shown in the Table below can
be performed.
Please perform each operation in accordance with the instructions in
the Table.
WIRELESS Menu
The WIRELESS menu is only enabled if the wireless function is enabled. Using the
wireless function requires a Wireless & Network Module Terminal (sold separately). See
the Wireless & Network Module Terminal user’s manual for more information about the
WIRELESS menu. Contact your local dealer for more information about the wireless
function and Wireless & Network Module Terminal.
MENU
: SELECT
MAIN
PICTURE-1
PICTURE-2
INPUT
AUTO
SCREEN
OPTION
WIRELESSVOLUME
WHISPER
IR REMOTE
LAMP TIME
FILTER TIME
12
ItemDescription
VOLUMEAdjust Volume:High Low
WHISPER
Select WHISPER Mode: 
NORMAL WHISPER
When WHISPER is selected  the WHISPER mode is activated. In the WHISPER
mode, acoustic noise and screen brightness are reduced. 
IR REMOTE
Selecting the remote control receiver: 
The unit has 3 remote control receivers, as shown in the figure
to the right (1, 2, and 3). You can select which of them to
activate (“v” in the figure), and which to disable.
• The ambient lighting and other factors may prevent the
remote control operation from functioning properly. If this
happens, use this function to disable receivers being
impacted by unneeded light.
LAMP TIME
Refer to LAMP TIME: When set, this function displays the total time the
projector lamp has been used since new.
Reset LAMP TIME  [Use this function only when the lamp has been replaced!]:Depress the RESET button for at least 3 seconds while lamp time is being
displayed. The reset menu will then appear. After you replace the lamp with a
new lamp, select RESET on the menu with the  button.
• Do not reset the lamp time unless you have replaced the lamp. And, always
reset the lamp time when replacing the lamp. The message functions will not
operate properly if the lamp time is not reset correctly.
•
Before replacing the lamp, carefully read the descriptions headed THE LAMP.
FILTER TIME
Refer to FILTER TIME:This function displays the total time the air-filter has
been used since new.
Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]:Depress the RESET button for at least 3 seconds while lamp time is being
displayed. The reset menu will then appear. After you replace the filter, select
RESET on the menu with the  button.
RESET 
CANCEL
• Do not reset the filter time unless you have cleaned or replaced the filter. And,
always reset the filter time when cleaning or replacing the filter. The message
functions will not operate properly if the filter time is not reset correctly.
•
Before cleaning or replacing the filter, carefully read the descriptions headed THE AIR FILTER.
Example : OPTION Menu(VOLUME)OPTION Menu
11
22
3
12 3
12 3
12 3
12 3
12 3
12 33 
						

							MessageDescription
CHANGE THE LAMP
AFTER REPLACING LAMP, 
RESET THE LAMP TIMER.
(Note 1)Lamp usage time is approaching 2,000 hours. (Note 2)
Preparation of a new lamp, and an early lamp change, is
recommended. After you have changed the lamp, please be
sure to reset the lamp timer.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER 
hr.(Note 1)
Lamp usage time is approaching 2,000 hours. A lamp change
within hours is recommended. (Note 2)
When lamp usage reaches 2,000 hours, the power will
automatically be turned OFF. Please change the lamp by
referring to “THE LAMP” (Vol.1       ). After you have
changed the lamp, please be sure to reset the lamp
timer.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER 0 hr.As lamp use has reached 2,000 hours, the power will soon be
automatically turned OFF. (Note 2)
Please immediately turn the power OFF, and follow the
instructions in the “THE LAMP”(Vol.1       ).
After you have changed the lamp, please be sure to reset the
lamp timer. (        )
CLEAN THE AIR FILTER
AFTER CLEANING AIR FILTER,
RESET THE FILTER TIMER.A note of precaution when cleaning the air filter.
After cleaning the filter, operate FILTER TIME of the OPTION
Menu (       ), and perform reset of the filter timer.
NO INPUT IS DETECTED
ON  There is no input signal.
Please confirm the signal input connection, and the status of the
signal source.
SYNC IS OUT OF RANGE
ON kHzHz
The horizontal or vertical wavelength of the inputted signal is
outside of the response parameters of this unit. Please confirm
the specs for this unit or the signal source specs.
CHECK THE AIR FLOW
The internal portion temperature is rising. Please turn the power
OFF, and allow the unit to cool down for approximately 20
minutes. After having confirmed the following items, then please
resent the power to ON.
•Is there blockage of the air passage aperture?•Is the air filter dirty?•Does the peripheral temperature exceed 35°C?
8
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED 
Related Messages
When the units power is ON, messages such as those shown below may be displayed. When
any such message is displayed on the screen, please respond as described below.
Note 1: Although this message will be automatically disappeared after around 3 minutes, it will be
reappeared every time the power is turned ON.
Note 2: Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of
usage, a lamp will no longer light up, or the lamp will break or burst, etc. This unit is equipped
with an automatic shut-down function, such that the power will automatically be turned OFF
when lamp usage time has reached 2,000 hours. Please be aware, however, that among lamp
types, there are major differences in product lifetimes; a lamp may thus fail to light even prior
to the functioning of the automatic shut-down function of this unit.
NOTES
fHfV
27
27
7
7 
						

							9
Regarding the Indicator Lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the
TEMP indicator have the meanings as described in the Table below.
Please respond in accordance with the instructions within the Table.
POWER
indicatorLAMP
indicatorTEMP
indicatorDescription
The orange
lamp is lightedTurned OFF
(Not lighted)Turned OFF
(Not lighted)The STANDBY mode is set
Flashing of the green lampTurned OFFTurned OFFThe unit is warming up. Please wait.
The green lamp is lightedTurned OFFTurned OFFThe unit is in an ON state. Ordinary operations may be performed.
Flashing of the orange lampTurned OFFTurned OFFThe unit is cooling down. Please wait.
Blinking of the
red lamp--
The unit is cooling down. Please wait.
A certain error has been detected. Wait until the POWER indicator lamp has finished
flashing, and then perform the proper response measure using the item descriptions
below as reference.
The red lamp
is lighted, or
blinksThe red lamp
is lightedTurned
OFF
The lamp does not light.
There is a possibility that the interior portion has become heated. Turn the power OFF and wait
approximately 20 minutes. After the main unit has cooled down, please confirm whether or not
there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or
not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,
turn the power ON again; if the same display is displayed, then please change the lamp.
The red lamp
is lighted, or
blinksBlinking of the
red lampTurned
OFF
Either there is no lamp and/or lamp cover, or either of these has not been properly fixed
(attached). Turn the power OFF and wait approximately 45 minutes. After the main unit has
sufficiently cooled down, please make confirmation of the attachment state of the lamp and
lamp cover. After performing any needed maintenance, turn the power ON again; if the same
display is displayed, then please contact a sales store or a service company.
The red lamp
is lighted, or
blinksTurned
OFFBlinking of the
red lampThe cooling fan is not operating. Turn the power OFF and wait approximately 20 minutes. After the
main unit has cooled down, please make confirmation that no foreign matter has become caught in
the fan, etc. After performing any needed maintenance, turn the power ON again; if the same display
is displayed, then please contact a sales store or a service company.
The red lamp is
lighted, or
blinksTurned
OFFThe red lamp is
lighted
There is a possibility that the interior portion has become heated. Turn the power OFF and wait
approximately 20 minutes. After the main unit has cooled down, please confirm whether or not
there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or
not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,
turn the power ON again; if the same display is displayed, then please contact a sales store or a
service company.
The green lamp
is lightedAlternative blinking
with the red lampThere is a possibility that the interior portion has become overcooled. Please use the unit within
the usage temperature parameters (0°C to 35°C). After performing any needed maintenance,
turn the power ON again; if the same display is displayed, then please contact a sales store or a
service company.
The green
lamp is lightedSimultaneous blinking
with the red lampThis is a notification that it is time to clean the filter.
After cleaning the filter, operate the FILTER TIME portion of the OPTION Menu, and perform
reset of the FILTER TIME.
When the interior portion has become overheated, for safety purposes, the power source is automatically turned OFF,
and the indicator lamps may also be turned OFF. Press the “
” (power OFF) side of the main power switch, and wait
for approximately 20 minutes. Please then use the unit only after having first confirmed that the unit has sufficiently
cooled down.
NOTE
9 
						

							10
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued)
Phenomena That May Easily Be Mistaken for Machine Defects
Before requesting repair, check in accordance with the following chart.
If the situation cannot be corrected, then contact your dealer.
Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and
such do not constitute or imply a machine defect. 
NOTE
PhenomenonCases not involving a machine defectItems to be confirmedReference
Page(s)
Power does not
come ON
The main power source is not ON.Turn on the main power.Vol.1-3, 15The electrical power cord is not plugged in.Correctly connect the power cord.
The main power source has been
interrupted during operation, such as by
a power outage (blackout), etc.Be sure to press the “O” (power OFF) side
of the main power switch, and leave this OFF
for approximately 20 minutes. After the unit
has sufficiently cooled down, turn ON the
power source.
Vol.1-15
No sound or
pictures are
outputtedThe input changeover settings
are mismatched.Select the input signal, and
correct the settings.Vol.1-16
No signal is being inputted.Correctly connect the connection cord.Vol.1-8-12
Pictures are
displayed, but no
sounds are heard
The electrical wiring to this unit
is not correctly connected.Correctly connect the connection cord.Vol.1-8-12
The volume setting has been set at (or
adjusted to) an extremely low level.Adjust the VOLUME setting to a higher level.Vol.1-18
The MUTE mode is the current setting.Press the MUTE button to release
(change) the MUTE mode setting.Vol.1-18
Sounds are
heard, but no
pictures are
displayed
The electrical wiring to this unit
is not correctly connected.Correctly connect the connection cord.Vol.1-8-12
The brightness setting has been set at
(or adjusted to) an extremely low level.Adjust the BRIGHT setting to a
brighter level.Vol.2-2
The lens cap has not been removed.Remove the lens cap.Vol.1-15
Colors have a faded-
out appearance
Color tone is poorColor depth setting or color tone settingPerform picture adjustments by changing the
COLOR BAL R, the COLOR BAL B, and/or the
TINT settings, etc.
Vol.2-3
Pictures appear
dark
The brightness setting and/or contrast
setting has not been properly adjusted.Perform picture adjustments by changing the
BRIGHT and/or CONTRAST settings, etc.Vol.2-2
The WHISPER mode is the current
setting.Change (by releasing) from the
WHISPER mode.Vol.2-7
Lamp is approaching the end of its
product lifetime.Exchange the old lamp with a new
lamp.Vol.1-27, 28
Pictures appear
blurryEither the FOCUS setting or the H
PHASE is not properly adjusted.Adjust the FOCUS and H PHASE settings.Vol.1-16
Vol.2-3 
Input signal changes
with no-operation.INPUT dial is set between the click
points.Turn the INPUT dial and set it at the
click point.Vol.1-16