Dukane Imagepro 8711 Lcd Projector Users Manual

							13
1Remove the battery cover
Slide back and remove the battery cover in the direction of the
arrow.
Insert the batteries
Align and insert the two AA batteries (that came with the
projector) according to their plus and minus terminals (as
indicated in the remote control).
Close the battery cover
Replace the battery cover in the direction of the arrow and
snap it back into place.
2
3
USING THE REMOTE CONTROL
CAUTIONPrecautions to observe in regards to the batteries
Always handle the batteries with care and use them only as directed. Improper use may result in
battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.
• Keep the battery away from children and pets.
• 
Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.
• When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control).
• When you dispose the battery, you should obey the law in the relative area or country.
Putting batteries into the remote control unit
$1987PM&
y




1.


						

							• The remote control works with both the
projectors front and rear remote sensors.
• The range of the remote sensor on the front is 3
meters with a 60-degree range (30 degrees to the
left and right of the remote sensor), and back is 3
meters with a 40-degree range.
• Since the remote control uses infrared light to send
signals to the projector (Class 1 LED), be sure to use
the remote control in an area free from obstacles
that could block the remote controls output signal to
the projector.
• The wired remote control:
You can use the remote control as a wired remote control, by connecting the REMOTE CONTROL ports of the
main unit and remote control via an audio cable (3.5 dia. stereo mini cable with plugs).
approximately
3 meters30 degrees30 degrees
approximately
3 meters20 degrees20 degrees
Precautions to observe when using the remote control
• Do not disassemble the remote control. 
• Do not drop or otherwise expose the remote control to physical impact.
• 
Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.
• Do not place the remote control near the projector’s lens, fan, or vents.
• Remove the batteries from the remote control and store them in a safe place if you
wont be using the remote control for an extended period. 
• Replace the batteries whenever the remote control starts to malfunction.
• 
When strong light, such as direct sunlight or light from an extremely close range (such as from an
inverter fluorescent lamp), hits the projectors remote sensor, the remote control may cease to function.
Adjust the direction of the projector to keep light from directly hitting the projectors remote sensor.
ATTENTION
14
Operating the remote control
USING THE REMOTE CONTROL (continued)
WARNING• The laser pointer of the remote control transmitter is used in
place of a finger or rod. Never look directly into the laser beam outlet or point
the laser beam at other people. The laser beam can cause vision problems.
CAUTION
• Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
$1987PM&
y




1.


						

							15
1Make sure that the power cord is firmly and
correctly connected to the projector and outlet
2Turn on the projectors power
Set the power switch to [ | ] (ON). The STANDBY/ON
indicator will light to solid orange.
3Press the STANDBY/ON button (control
panel or remote control) 
• The projector begins warming up and the
STANDBY/ON indicator blinks green.
• The STANDBY/ON indicator stops blinking
and lights to solid green once the
projectors power is completely on.
4Remove the lens cap
The picture is projected.
power switch
STANDBY/ON indicator

STANDBY/ONVIDEO
UP
DOWN
BLANK
LASER
INDICATOR
LASER
RGB
FOCUSZOOM PAGE
TURNING ON THE POWER
Precautions 
Connect all devices to be used to the projector prior to turning on the power.™
WARNINGWhen the power is ON, a strong light is emitted. Do not look into the
lens.
Turn the
power on/off in
right order.
• Power on the
projector before the
computer or video
tape recorder.
• Power off the
projector after the
computer or video
tape recorder.
NOTE
Control panel
STANDBY/ONINPUT
KEYSTONE
RESET
MENU
LANP TENPONE TOUCH RGB
BNC
DVI
VIDEO
S-VIDEO
COMPONENTFOCUS ZOOM
STANDBY/ON
$1987PM&
y




1.


						

							6Use the ZOOM  /  buttons to adjust
the screen size
7Use the FOCUS  /  buttons to adjust
the focus
5
If selecting RGB input
Press the RGB button
Press this button to toggle between the devices
connected to RGB IN 1 and 2. As illustrated
below, each time you press the RGB button, the
projector switches between RGB IN 1 and 2.
Select the signal you wish to project.
If selecting video input
Press the VIDEO button
Press this button to toggle between the
devices connected to VIDEO IN, S-VIDEO
IN and COMPONENT VIDEO. As
illustrated below, each time you press the
VIDEO button, the projector switches between
VIDEO IN, S-VIDEO IN and COMPONENT VIDEO.
Select the signal you wish to project.
Using the remote control
Turn the INPUT dial
Turning the dial cycles
through the inputs as
shown below. Select the
terminal to which the signal
you want to project is input.
Using the projectors control panel
INPUTGB
Selecting an Input Signal
16
TURNING ON THE POWER (continued)
RGB
VIDEO
VIDEO IN S-VIDEO IN COMPONENT VIDEO
VIDEO IN S-VIDEO IN COMPONENT VIDEO
BNC(COMPONENT)
RGB BNC(RGB) DVI
RGB DVI
• When BNC (RGB) is selected:• When BNC (RGB) is selected:
• When BNC (COMPONENT) is selected:
• When BNC (RGB) is selected:
• When BNC (COMPONENT) is selected:
RGB BNC(RGB) DVI
S-VIDEO VIDE
OCOMPONENT VIDEO
RGB BNC(COMPONENT) DVI
S-VIDEO VIDE
OCOMPONENT VIDEO
• When BNC (COMPONENT) is selected:
ZOOM
ZOOM
(Remote control) (Control panel)
(Remote control) (Control panel)
FOCUS
FOCUS
Turn the INPUT dial and set it at the
click point, otherwise input signal
selection may be incorrect.
NOTE
$1987PM&
y




1.


						

							17
1Press the STANDBY/ON button (control
panel or remote control)
The message Power off? will appear on the screen for
approximately 5 seconds. 
3Check that the STANDBY/ON indicator
stops blinking and lights to
solid orange.
Switch the power switch to
[O] (OFF).
4Confirm that the STANDBY/ON indicator has
gone off and then attach the lens cap.
When the projector has completed powering down, the
STANDBY/ON indicator will go off.
TURNING OFF THE POWER
2Press the STANDBY/ON button again
(control panel or remote control)
Press the STANDBY/ON button again while the Power off?
message is visible. The projector lamp goes off and starts cooling
down. While cooling, the STANDBY/ON indicator flashes orange.
When in this state, pressing the STANDBY/ON button has no
effect. 
When lamp cooling is complete, the STANDBY/ON indicator stops
flashing, and turning solid orange.
• Except in cases of
emergency, do not turn off
the power switch while the
STANDBY/ON indicator is
solid or flashing green.
Doing so could shorten
the lamp lifetime.
NOTE
Control panel
STANDBY/ONINPUT
KEYSTONE
RESET
MENU
LANP TENPONE TOUCH RGB
BNC
DVI
VIDEO
S-VIDEO
COMPONENTFOCUS ZOOM
STANDBY/ON indicator
STANDBY/ON
STANDBY/ON
STANDBY/ONVIDEO
UP
DOWN
BLANK
ASPECT
PUSHLASER
INDICATOR
LASER
RGB
FOCUS
ENTER
ON
OFF ESC MENU RESET
POSITION
MAGNIFY VOLUME
MUTE
WIRELESS KEYSTONE
FREEZE
ONE TOUCH
AUTOPinP ZOOM
PA G E
power switch
$1987PM&
y




1.


						

							1Press the VOLUME button
As illustrated on the right, a dialog will
appear on the screen to aid you in adjusting
the volume.
1Press the MUTE button
As illustrated on the right, a dialog will appear on the
screen indicating that you have muted the sound.  Press
the VOLUME button to close the dialog.  (Even if you dont
do anything, the dialog will automatically disappear after
a few seconds.)
Press the MUTE button again to restore the sound.
2Use the lever switch  /  to adjust the
volume
Press the VOLUME button again to close the dialog and
complete this operation.  (Even if you dont do anything, the
dialog will automatically disappear after a few seconds.)
Press this to increase the volume
Press this to decrease the volume
16
VOLUME
16
VOLUME
16
VOLUME
ADJUSTING THE VOLUME
TEMPORARILY MUTING THE SOUND
18
STANDBY/ONVIDEO
UP
DOWN
BLANK
ASPECT
PUSHLASER
INDICATOR
LASER
RGB
FOCUS
ENTER
ON
OFF ESC MENU RESET
POSITION
MAGNIFY VOLUME
MUTE
WIRELESS KEYSTONE
FREEZE
ONE TOUCH
AUTOPinP ZOOM
PA G EVOLUME
MUTE
DOWN
BLANK
ASPECT
PUSH
LASER
ENTER
ON
OFF ESC MENU RESET
POSITION
MAGNIFY VOLUME
MUTE
WIRELESS KEYSTONE
FREEZE
ONE TOUCH
AUTOPinP
$1987PM&
y




1.


						

							19
1Press the POSITION button
As illustrated on the right, a dialog will appear on the screen to
aid you in adjusting the position.
2Use the , , , buttons to adjust the
position
When you want to initialize the position, press the RESET
button during adjustment.
Press the POSITION button again to close the dialog and
complete this operation.  (Even if you dont do anything, the
dialog will automatically disappear after a few seconds.)
This function is only available for RGB/BNC (RGB) input.
ADJUSTING THE POSITION
POSITION
STANDBY/ONVIDEO
UP
DOWN
BLANK
ASPECT
PUSHLASER
INDICATOR
LASER
RGB
FOCUS
ENTER
ON
OFF ESC MENU RESET
POSITION
MAGNIFY VOLUME
MUTE
WIRELESS KEYSTONE
FREEZE
ONE TOUCH
AUTOPinP ZOOM
PA G E
POSITION
$1987PM&
y




1.


						

							The automatic adjustment operation requires approximately 10 seconds. Also, please
note that it may not function correctly with some input signals.
NOTE
1
USING THE AUTOMATIC ADJUSTMENT FEATURE
Press the AUTO button
Horizontal position (H. POSIT), vertical position (V.
POSIT), clock phase (H. PHASE) and horizontal size (H.
SIZE) are automatically adjusted.
Make sure that the application window is set to its
maximum size prior to attempting to use this feature.
Dark pictures may still be incorrectly adjusted. Use a
bright screen when adjusting.
The signal type best suited for the respective input
signal is selected automatically.
This feature is available only if VIDEO is set to AUTO in
the INPUT menu.
Automatic Adjustment for RGB Input
Automatic Adjustment for Video Input
20
BLANK
ASPECT
PUSH
LASER
ENTER
ON
OFF ESC MENU RESET
POSITION
MAGNIFY VOLUME
MUTE
WIRELESS KEYSTONE
FREEZE
ONE TOUCH
AUTOPinP
AUTO
$1987PM&
y




1.


						

							21
• This function may not be work well with some types of input signals.
• The adjustable range for correcting keystone distortions will vary with the type of
input signal.
NOTE
CORRECTING KEYSTONE DISTORTIONS
1Press the KEYSTONE button
As illustrated on the right, a dialog will appear
on the screen to aid you in correcting the
distortion. 
2Use the , buttons to select the
direction of distortion to correct ( / )
3Use the lever switch/ to correct
distortion
Press the KEYSTONE button again to close the dialog and
complete this operation.  (Even if you dont do anything, the
dialog will automatically disappear after a few seconds.)
16
KEYSTONE
ASPECT
PUSHENTER
ON
OFF ESC MENU RESET
POSITION
MAGNIFY VOLUME
MUTE
WIRELESS KEYSTONE
FREEZE
ONE TOUCH
AUTOPinP
KEYSTONE
$1987PM&
y




1.


						

							The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,
AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signals state.
NOTE
•The projector will automatically exit from FREEZE mode if either the POSITION, VOLUME, MUTE, AUTO,
BLANK ON/OFF or MENU ON/OFF feature is used, or, if there is a change in the input signals state.
•If the projector continues projecting the same image for a long time (i.e. you forget to exit FREEZE mode),
the image might possibly remain as an afterimage. Do not leave the projector in FREEZE mode for too long.
NOTE
USING THE MAGNIFY FEATURE
FREEZING THE SCREEN
1Press the MAGNIFY (ON) button
The projector enters MAGNIFY mode.
2Press the POSITION button, then use the lever switch
/  ,  /  to select the area to zoom. Press the
POSITION button again to finalize the zoom area.
3Use the lever switch  /  to adjust the
zoom level
Press the MAGNIFY (OFF) button to exit MAGNIFY mode
and restore the screen to normal. (The projector will also
automatically exit MAGNIFY mode if there is a change in the
input signals state.)
1Press the FREEZE button
The [II] icon appears and the screen will freeze at
the current image. Press the FREEZE button again
and the [  ] appears as the projector exits FREEZE
mode.
Û
22
DOWN
BLANK
ASPECT
PUSH
LASER
ENTER
ON
OFF ESC MENU RESET
POSITION
MAGNIFY VOLUME
MUTE
WIRELESS KEYSTONE
FREEZE
ONE TOUCH
AUTOPinP
ONMAGNIFY
POSITIONPOSITION
PUSHENTER
ON
OFF ESC MENU RESET
POSITION
MAGNIFY VOLUME
MUTE
WIRELESS KEYSTONE
FREEZE
ONE TOUCH
AUTOPinP
FREEZE
$1987PM&
y




1.