Dukane Imagepro 8711 Lcd Projector Users Manual

13
1Remove the battery cover
Slide back and remove the battery cover in the direction of the
arrow.
Insert the batteries
Align and insert the two AA batteries (that came with the
projector) according to their plus and minus terminals (as
indicated in the remote control).
Close the battery cover
Replace the battery cover in the direction of the arrow and
snap it back into place.
2
3
USING THE REMOTE CONTROL
CAUTIONPrecautions to observe in regards to the batteries
Always handle the batteries with care and...

• The remote control works with both the
projectors front and rear remote sensors.
• The range of the remote sensor on the front is 3
meters with a 60-degree range (30 degrees to the
left and right of the remote sensor), and back is 3
meters with a 40-degree range.
• Since the remote control uses infrared light to send
signals to the projector (Class 1 LED), be sure to use
the remote control in an area free from obstacles
that could block the remote controls output signal to
the projector.
• The wired...

15
1Make sure that the power cord is firmly and
correctly connected to the projector and outlet
2Turn on the projectors power
Set the power switch to [ | ] (ON). The STANDBY/ON
indicator will light to solid orange.
3Press the STANDBY/ON button (control
panel or remote control) 
• The projector begins warming up and the
STANDBY/ON indicator blinks green.
• The STANDBY/ON indicator stops blinking
and lights to solid green once the
projectors power is completely on.
4Remove the lens cap
The picture is...

6Use the ZOOM  /  buttons to adjust
the screen size
7Use the FOCUS  /  buttons to adjust
the focus
5
If selecting RGB input
Press the RGB button
Press this button to toggle between the devices
connected to RGB IN 1 and 2. As illustrated
below, each time you press the RGB button, the
projector switches between RGB IN 1 and 2.
Select the signal you wish to project.
If selecting video input
Press the VIDEO button
Press this button to toggle between the
devices connected to VIDEO IN, S-VIDEO
IN and COMPONENT...

17
1Press the STANDBY/ON button (control
panel or remote control)
The message Power off? will appear on the screen for
approximately 5 seconds. 
3Check that the STANDBY/ON indicator
stops blinking and lights to
solid orange.
Switch the power switch to
[O] (OFF).
4Confirm that the STANDBY/ON indicator has
gone off and then attach the lens cap.
When the projector has completed powering down, the
STANDBY/ON indicator will go off.
TURNING OFF THE POWER
2Press the STANDBY/ON button again
(control panel or...

1Press the VOLUME button
As illustrated on the right, a dialog will
appear on the screen to aid you in adjusting
the volume.
1Press the MUTE button
As illustrated on the right, a dialog will appear on the
screen indicating that you have muted the sound.  Press
the VOLUME button to close the dialog.  (Even if you dont
do anything, the dialog will automatically disappear after
a few seconds.)
Press the MUTE button again to restore the sound.
2Use the lever switch  /  to adjust the
volume
Press the VOLUME...

19
1Press the POSITION button
As illustrated on the right, a dialog will appear on the screen to
aid you in adjusting the position.
2Use the , , , buttons to adjust the
position
When you want to initialize the position, press the RESET
button during adjustment.
Press the POSITION button again to close the dialog and
complete this operation.  (Even if you dont do anything, the
dialog will automatically disappear after a few seconds.)
This function is only available for RGB/BNC (RGB) input.
ADJUSTING THE...

The automatic adjustment operation requires approximately 10 seconds. Also, please
note that it may not function correctly with some input signals.
NOTE
1
USING THE AUTOMATIC ADJUSTMENT FEATURE
Press the AUTO button
Horizontal position (H. POSIT), vertical position (V.
POSIT), clock phase (H. PHASE) and horizontal size (H.
SIZE) are automatically adjusted.
Make sure that the application window is set to its
maximum size prior to attempting to use this feature.
Dark pictures may still be incorrectly...

21
• This function may not be work well with some types of input signals.
• The adjustable range for correcting keystone distortions will vary with the type of
input signal.
NOTE
CORRECTING KEYSTONE DISTORTIONS
1Press the KEYSTONE button
As illustrated on the right, a dialog will appear
on the screen to aid you in correcting the
distortion. 
2Use the , buttons to select the
direction of distortion to correct ( / )
3Use the lever switch/ to correct
distortion
Press the KEYSTONE button again to close the...

The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,
AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signals state.
NOTE
•The projector will automatically exit from FREEZE mode if either the POSITION, VOLUME, MUTE, AUTO,
BLANK ON/OFF or MENU ON/OFF feature is used, or, if there is a change in the input signals state.
•If the projector continues projecting the same image for a long time (i.e. you forget to exit FREEZE mode),
the image might...