Dillon Precision Super 1050 Instruction Manual
Have a look at the manual Dillon Precision Super 1050 Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 7 Dillon Precision manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
case has been flattened out. 2.) High primers: a.) Adjust the primer push rod (#12819). b.) On .223 cases the swage back-up rod (#13332) is down too far, slightly collapsing the primer pocket and not allowing the primer to seat fully. c.) Loose shellplate (#12600*). d.) Erratic handle motion. e.) Do not remove the rubber piece on the primer slide. 3.) Smeared primers - see Station 3: Primer Pocket Swaging - item 1 4.) Locator tab: a.) When adjusting the priming sta- tion locator tab, it should be set as close to the case as possible without touching it. Be sure the cases in the shellplate rotate freely past the tab. Change primer magazine tips every 20,000 rounds. Note: Move the handle down, bringing the toolhead down. Move the locator tab in to the case in the priming station. Station 5. Powder and Case Mouth Belling Problems 1.) Crushing cases: a.) Wrong size or missing locator buttons. 2.) Spilling powder: a.) Slamming or going too fast with the operating handle (#12727). b.) Stick or pencil-lead type pow- ders bridging on the case mouth in the powder funnel (#13005). See conver- sion chart. c.) Check powder bar adjustment. 3.) Erratic belling: a.) Variation in case length. Divide cases by brand. b.) Handle not moving all the way down on each stroke. Note: Try setting a bullet on the case mouth in Station 6. 4.) Erratic powder charges: a.) Powder bar not moving full length of its travel. Turn the powder die down until it does. Station 7: Bullet Seating Problems 1.) Erratic seating depth of the bullet: a.) Build up of lead shaving and/or lube in the seater or crimp dies. b.) Bullets having erratic dimension(length and/or the ogive). c.) Use the proper seating stem for the type of bullet being used. d.) Variations in case types and/or lots – sort brass. e.) Refer to a loading manual for proper loaded length (OAL) and addi- tional information. Station 8: Crimping Problems 1.) Erratic crimping: a.) Length of cartridge cases erratic, probably due to mixed brands of brass. b.) Worn out or improperly made die, use Dillon dies whenever possible. 2.) Loose bullet: a.) Too much taper crimp. Note, this condition also ruins accuracy. b. Wrong expander (#12749*). c.) Thin cases. Maintenance Loctite Loctite should be used following adjustments to or replacement of all threaded screws. Please note that Loctite should be applied to threaded portions only and should be of a non- permanent type. Blue Loctite #242 is recommended. Swage Clean the swage by pulling the oper- ating handle down and use a small brush to clean the tip. Every 10,000 rounds, remove the swage rod (#20314 - large or #20313 - small). and clean, lightly grease and replace. Note: Do not grease the tip of the swage where it contacts the primer pocket. 21
Lubrication Operating circumstances will dictate the frequency of required lubrication. It is highly recommended that the Super 1050 be cleaned and lubed after every 10,000 rounds of operation. Use a high-grade, conventional wheel bearing grease – do not use oil. Lubrication Points: • Casefeed Plunger (#13073*), lube the sides and bottom. • Casefeed Plunger Roller (#13498) and Bolt (#13333) • Tappet (#12995) • Rocker Arm (#13058), cam surfaces and hole. • Pivot Bolt (#13296) • Primer Punch Base (#12849 - large or #13307 - small)• Lube the Indexing Lever Cam sur- face (#20312) and Index Lever Shoulder Bolt (#13276). With the handle in the rest position, you will see the Index Roller (#10996) come into contact with the Lever Cam sur- face. The Index Roller (#10996) also requires periodic lubrication. • Alignment Pins (#12972 & #13515 located under the toolhead) • Cam Guide Bolt (#12486) and its mated slot • Toolhead Bore (#20420 - lightly to avoid rusting and/or freezing up) • Mainshaft Lubrication – Use only 30 weight motor oil. DO NOT use a penetrating lubricant such as WD- 40, Breakfree, etc…• Swage Connecting Rod (#13417) and Clevis Pin (#13522) • Shellplate lock ring (#20311), bottom surface to shellplate face. • Shellplate center hole. It’s easiest to lubricate the shellplate center hole when changing from one caliber to another. We recommend that you use a droplet of Blue Loctite on the threads of the following bolts prior to reinstalling: #13333, #13296, and #13276 (see photos and schematics). 22 casefeed plunger (caliber specific) 13498 13333 12995 13296 13058 12849 large or 13307 small 12486 alignment pin Super 1050 mainshaft 10999 toolhead bore alignment pincasefeed cam 13417 13522 13276 20312 operating handle shown in down position 20311
23 10999 11000 11008 10994 11008 13685 11010 10996 11002 11009 Lube Points for the Super 1050 Crank Assembly With the handle in the rest position, on the left side of the machine, use a grease syringe to lube the bearing pin (#11009) located in the link arm (#11002). Then, cycle the handle down to the bottom stop. Again, using the grease syringe, lube the mainshaft pivot pin (#10994) on the left side of the machine via the access hole located 1.2" above the car- rier cap (#11010). Use 30 weight motor oil on the main- shaft (#10999).Towards the back of the machine, lube the indexing lever cam surface (#20312) and index lever shoulder bolt (#13276). When it is time to lube the roller bearings (#11008) in the frame and crankshaft, first remove the swage rod assembly, swage connecting rod, and operating handle. On the left side of the machine, use a 5/32" Allen wrench to remove the screw (#13685). Slide the carrier cap (#11010) out of its bore and lube the left-hand side roller bearing (#11008) and carrier cap. Next, slide the crankshaft (#11000) out of the framefrom the right side of the machine BUT NO MORE THAN 3/4". Using a grease syringe, dispense some grease onto the right-hand side roller bearing (#11008). Next, lube the crankshaft surface (#11000). Then, reinsert the crankshaft fully into the frame. Reinstall the carrier cap (#11010). Blue Loctite must be used on the threads before installation, tight- en. Finally, reassemble the swage com- ponent and operating handle back onto the frame. Lube the swage connecting rod (#13417) and clevis pin (#13522).
24 RL 1050 - Caliber Conversion Chart 20477 – .38/.357 Conversion 12704 #2 Shellplate 14062 #2 Locator Buttons (6) 13137 .38/.357 cal. Expander – D 13802 Adapter – Orange 13098 Casefeed Plunger – Medium 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13005 Powder Activator – Pistol 20478 – .41 Mag Conversion 11856 #6 Shellplate 13930 #1 Locator Buttons (6) 12882 .41 cal. Expander – H 13654 Adapter – Yellow 13073 Casefeed Plunger – Large 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13005 Powder Activator – Pistol 20479 – .44 Spl/Mag Conversion 12600 #4 Shellplate 14047 #4 Locator Buttons (6) 12628 .44 cal. Expander – G 13654 Adapter – Yellow 13073 Casefeed Plunger – Large 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13005 Powder Activator – Pistol 20480 – .45 ACP Conversion 12999 #1 Shellplate 13930 #1 Locator Buttons (6) 12749 .45 cal. Expander – E 13872 Adapter – Red 13073 Casefeed Plunger – Large 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13005 Powder Activator – Pistol 20481 – .45 LC Conversion 11235 #C Shellplate 14047 #4 Locator Buttons (6) 12749 .45 cal. Expander – E 13654 Adapter – Yellow 13073 Casefeed Plunger – Large 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13005 Powder Activator – Pistol 20482 – 9mm Conversion 12938 #5 Shellplate 14060 #3 Locator Buttons (6) 12833 9mm cal. Expander – F 13878 Adapter – Green 13306 Casefeed Plunger – Small 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13005 Powder Activator – Pistol 20483 – .380 Auto Conversion 12441 #3 Shellplate 14060 #3 Locator Buttons (6) 13285 .380 cal. Expander – F 13810 Adapter – White 12964 Casefeed Plunger – Small .380 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13419 1/4–28 Jam Nut 13017 Swage Back-up Rod – Large 12184 Swage Die 13483 9/16-18 Lock Nut 13005 Powder Activator – Pistol 20484 – .38 Super Conversion 12938 #5 Shellplate 14060 #3 Locator Buttons (6) 12833 9mm cal. Expander – F 13878 Adapter – Green 13306 Casefeed Plunger – Small 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13005 Powder Activator – Pistol 20788 – 10mm Auto Conversion 12940 #W Shellplate 14062 #2 Locator Buttons (6) 12912 10mm cal. Expander – W 13872 Adapter – Red 13098 Casefeed Plunger – Medium 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13005 Powder Activator – Pistol 20485 – .223 Conversion 12441 #3 Shellplate 14060 #3 Locator Buttons (6) 13332 Back-up/Expander .223 13426 Powder Funnel – A 12146 Adapter (pinned) – White, Long 13306 Casefeed Plunger – Small 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 12184 Swage Die 13483 9/16-18 Lock Nut 20626 – .30 Carbine Conversion 12655 #8 Shellplate 14048 #8 Locator Buttons (6) 12748 .30M1 cal. Expander – C 13564 Powder Funnel C 12641 Adapter – White, Slotted 13306 Casefeed Plunger – Small 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 20631 – 7.62x39 Conversion 11925 #A Shellplate 14062 #2 Locator Buttons (6) 13348 Back-up/Expander 7.62x39 13015 Powder Funnel AK 12943 Adapter 13098 Casefeed Plunger – Medium 13703 Casefeed Spacer 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 12184 Swage Die 13483 9/16-18 Lock Nut 14067 Die Lock Ring 20634 – .32 S&W Long/H&R Magnum Conversion 12107 #D Shellplate 14060 #3 Locator Buttons (6) 12780 .32 cal. Expander – S 12845 Powder Funnel – S 13878 Adapter – Green 13306 Casefeed Plunger – Small 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 21525 – 9x25 Dillon Conversion 12940 #W Shellplate 14062 #2 Locator Buttons (6) 12833 9mm cal. Expander – F 13872 Adapter – Red 13098 Casefeed Plunger – Medium 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13005 Powder Activator – Pistol 20545 – .40 S&W Conversion 12940 #W Shellplate 14062 #2 Locator Buttons (6) 12912 10mm cal. Expander – W 13878 Adapter – Green 13098 Casefeed Plunger – Medium 17384 Blue Locator Tab – Short (1) 13569 Blue Locator Tab (5) 14067 Die Lock Ring 13005 Powder Activator – Pistol
25 #21049 – .308 Conversion 11005 Super 1050 Adapter - .308 Win 12074 Back-up Expander - .308 12184 Swage Die Body - part 12999 #1 Shellplate 13073 Casefeed Plunger - large 13483 Old Style Jam Nut 9/16x18 13569 Blue Locator Tab (5) 13587 Powder Funnel - B, rifle 13930 Locator Pin - #1 (6) 14067 Die Lock Ring 17384 Blue Locator Tab, Short #21050 – .30-06 Conversion (only conversion kit that includes dies) 10840 .30-06 Die Set 11004 Super 1050 Adapter - .30-06 Win 12073 Back-up Expander - .30-06 12184 Swage Die Body - part 12999 #1 Shellplate 13073 Casefeed Plunger - large 13483 Old Style Jam Nut 9/16x18 13569 Blue Locator Tab (5) 13587 Powder Funnel - B, rifle 13930 Locator Pin - #1 (6) 14067 Die Lock Ring 17384 Blue Locator Tab, Short #21051 – .303 Conversion 12184 Swage Die Body - part 13073 Casefeed Plunger - large 13348 Back-up Expander - 762x39 13483 Old Style Jam Nut 9/16x18 13569 Blue Locator Tab (5) 13587 Powder Funnel - B, rifle 13654 Super 1050 Adapter - .41 Mag., .44, .45 LC 14047 Locator Pin - #4 (6) 14067 Die Lock Ring 16153 #N Shellplate 17384 Blue Locator Tab, Short #21052 – .30-30 Conversion 11005 Super 1050 Adapter - .308 Win 12068 1000/1050 .30-30 Expander 12075 #7 Shellplate 12184 Swage Die Body - part 13073 Casefeed Plunger - large 13483 Old Style Jam Nut 9/16x18 13569 Blue Locator Tab (5) 13587 Powder Funnel - B, rifle 14047 Locator Pin - #4 (6) 14067 Die Lock Ring 17384 Blue Locator Tab, Short #21053 – .270 Conversion 11004 Super 1050 Adapter - .30-06 Win 12069 1000/1050 .270 Expander 12184 Swage Die Body - part 12999 #1 Shellplate 13073 Casefeed Plunger - large 13456 Powder Funnel - J, rifle 13483 Old Style Jam Nut 9/16x18 13569 Blue Locator Tab (5) 13930 Locator Pin - #1 (6) 14067 Die Lock Ring 17384 Blue Locator Tab, Short #21054 – .243 Conversion 11005 Super 1050 Adapter - .308 Win 12070 1000/1050 .243 Expander 12184 Swage Die Body - part 12999 #1 Shellplate 13073 Casefeed Plunger - large 13305 Powder Funnel - I, rifle 13483 Old Style Jam Nut 9/16x18 13569 Blue Locator Tab (5) 13930 Locator Pin - #1 (6) 14067 Die Lock Ring 17384 Blue Locator Tab, Short #21055 – .22-250 Conversion 11005 Super 1050 Adapter - .308 Win 12071 1000/1050 .22-250 Expander 12184 Swage Die Body - part 12999 #1 Shellplate 13073 Casefeed Plunger - large 13426 Powder Funnel - A, rifle 13483 Old Style Jam Nut 9/16x18 13569 Blue Locator Tab (5) 13930 Locator Pin - #1 (6) 14067 Die Lock Ring 17384 Blue Locator Tab, Short #21056 – .45-70 Conversion 11007 Super 1050 Adapter - .45-70 12072 1000/1050 .45-70 Expander 12184 Swage Die Body - part 12705 1050 Custom Shellplate, #G 13072 Casefeed Plunger - .45-70 13407 Powder Funnel - T, pistol 13436 Locator Pin - #7 (6) 13483 Old Style Jam Nut 9/16x18 13569 Blue Locator Tab (5) 14067 Die Lock Ring 17384 Blue Locator Tab, Short Super 1050 - Caliber Conversion Chart The Super 1050 loads all of the calibers listed for the RL 1050 as well as the calibers listed below.
26 Super 1050 Parts Listing Part # Description 10991 Bin Support Bracket 10992 Inside Frame Stop 10993 Spent Primer Cup Bracket 10994 .560 dia. Mainshaft Pin 10995 Index Lever 10996 Index Roller 10997 Super 1050 Frame 10999 Mainshaft 11000 Crank Shaft 11001 Crank Arm 11002 Link Arm 11003 Lever Arm 11006 Super 1050 Modified Casefeed Housing 11008 BH-1610 Roller Bearing 11009 1.00 dia. Pin 11010 Carrier Cap 11011 Super 1050 Manual 12144 Bullet Bin Bracket 12184 Swage Die Body – Part 12260 1050 Box For Shipping 12486 Cam Guide Bolt 1/4x20 12572 Toolhead Spring 12819 Primer System Push Rod 12930 Primer Station Retain Tab 12972 Toolhead Alignment Rod 12995 Primer System Tappet 13001 New Lever Arm Bracket 13058 Primer System Rocker Arm 13064 Swage Cover 1050 13073 Casefeed Plunger – Large 13089 Return Rod Eye Bolt 13091 Alignment Bushing – New 13098 Casefeed Plunger – Medium 13108 Primer Slide Stop “B” 13161 Casefeed Cam1050 13189 1050 Ejector Tab 13205 Post Bolts 13226 Rocker Arm Set Screw 13238 Bin Bracket 13244 Crank Retaining Pin (2) 13245 Primer Swage Adjustment Bolt 13262 7/32” Hex Wrench (Short) 13271 Post Stud 13276 Index Lever Shoulder Bolt 13296 Primer System Rocker Bolt 13306 Casefeed Plunger – Small 13333 Locator Tab Bolt 13335 Spring Bushing 13342 Toolhead Bolt 13363 Primer Magazine Socket Bolt 13377 Bin Bracket Mount Screw 13417 Swage Connecting Rod 13419 Swage Rod Lock Nut 13426 Powder Funnel A – Rifle 13432 Crank Handle Lock Screw 13435 1/4” Hex WrenchPart # Description 13449 Toolhead Washer 13475 Journal Key 1050 13483 Old Style Jam Nut 9/16x18 13484 1050 Cartridge Bin 13495 Lower Cord Clamp 13498 Plunger Roller 1050 13502 Clamp Retaining Screw 13508 Index Ball 1050 13515 Slide Alignment Pin 13522 Clevis Pin 13525 Index Ball Spring 1050 13534 Casefeed Adapter Housing 13561 Lock Ring Insert 13567 Casefeed Plunger Spring 13581 Grease Zerts 13593 5/32” Hex Wrench 13607 Rocker Bolt Lock Washer 13611 Casefeed Post Warning Label 13624 Index Pawl Spring 13644 Small Powder Bar Spacer 13650 Spent Primer Cup 13655 5/16 Washer 13664 5/16-18 Nut 13682 Swage Lock Nut 1050 13685 1/4-20x1/2 Bracket Bolt 13696 3 Packing Foam Pieces 13701 Index Pawl Pin 3/8 13705 1050 Index Pawl 13728 1/8” Hex Wrench 13738 #10 Washer for Roller 13746 Actuating Lever Cotter Pin 13756 1050 Bullet Bin 13761 Casefeed Tube 1050 13793 Collar Roller 13799 Strip Nut 13801 Tinnerman Insert 13813 Clutch Spring Washer 13815 Adapter Housing Screw 13818 Powder Bar Insert – Small 13827 3/16” Hex Wrench 13840 Hair Pin Cotter 13844 Short Lever Spring 13845 Body Collar Sleeve 13848 Bellcrank Bushing 13853 Powder Bar Insert – Large 13858 Primer Punch Spring 1050 13859 Casefeed Tube Clip 13871 Bellcrank Cube 13882 Powder Measure Lid 13886 3/32” Hex Wrench 13888 E-Clip 13893 Powder Bar Post – Large 13895 10-24 x 3/8” BH Screw (6) 13896 1/4-20 3/8 BH – Ejector Tab Screw 13904 Bellcrank Bolt 13921 Powder Bar Spacer Plug 13929 Return Rod ClipPart # Description 13939 Body Collar Clamp – Part 13943 Powder Bar Adjustment Screw 13944 Indexer Return Spring 13951 Powder Bar Post – Small 13955 Lower Plate Screw 13957 Magazine Shield Cap 1050 13958 Powder Bar Bolt Washer 13960 Powder Bar Return Rod – Part 13964 10-24x1/4 BHCS for Index Roller 13972 3/16 Roll Pin 14003 Magazine Orifice – Large – Red 14023 10-24 5/8 Buttonhead Screw 14024 Magazine Orifice – Small – Blue 14033 Return Rod Spring 14036 Old Powder Bar Return Spring 14037 10-24x3/4 SHCS – Collar Clamp Screw (2) 14067 Die Lock ring 14202 Powder Measure Tube Screw 14517 Swage Station Bushing 14808 Collar Roller Bushing 14990 Slide Roll Pin Sleeve 16699 Spent Primer Cup 17069 Snap Ring 17141 1/4” Hardened Washer 17604 Bracket Pivot Pin 17808 Casefeed Bowl Insert 20062 Small Powder Bar Assembly 20063 Large Powder Bar Assembly 20311 1050 Lock Ring Assembly 20312 1050 Index Lever Assembly 20313 Swage Rod 1050 – Small 20314 Swage Rod 1050 – Large 20317 1050 Primer Slide – Small 20318 1050 Primer Slide – Large 20320 Powder Die 20322 Casefeed Assembly 1050 – Large Pistol 20324 Casefeed Assembly 1050 – Small Rifle 20341 1050 Bushing Driver 20419 1050 Primer System – Small 20420 1050 Toolhead Assembly 20421 Auto Powder System 20476 1050 Primer System – Large 20488 1050 Primer Arm/Cam – Assembly 20635 Ratchet Detent Assembly 20641 Casefeed Mounting Post – Assembly 20773 Primer Feed Body/Shield 20785 Powder Measure Body 21072 Casefeed Plate – Large Pistol 21073 Casefeed Plate – Small Pistol 21074 Casefeed Plate – Small Rifle 21079 Casefeed Assembly 1050 – Small Pistol 21275 Body Collar – Complete 21530 Floating Decap Assembly
27 Super 1050 Upper Machine Assembly #17071 – Handle Assembly 17918 12727 11000 13432 17069 11000 #20420 – Toolhead Assembly 13342 13449 2042013957 20773 13955 13108 13276 1394412930 13895 13650 13896 10993 13896 131891352513508 1322613089 13425 2063513335 12572 13895 13561 *20637 See page 29 for more detail. 13342 1281913005 - 13015refer to the caliber conversion chart 20320 14067 Seating Die Sizing Die 14067 10999 13161138961714112486 2042013449 Crimp Die 20312 assembly 20311 assembly Shellplate – caliber specific, refer to the caliber conver- sion chart20317 – small 20318 – large Expander – refer to the caliber conversion chart
28 10999 11000 13475 11008 11001 11008 13244 11009 10994 13244 11002 11008 13685 11010 13895 13738 10996 14517 20313 - small assembly 20314 - large assembly 13064 13896 13682 13245 13417 1358113840 13522 See page 31 – Casefeed Frame Assembly See Item A above Super 1050 Lower Machine Assembly Item A – Swage Rod AssemblyLower Machine AssemblyPart # Description 10994 Mainshaft Pivot Pin - .560” dia. 10996 Index Roller 10999 Super 1050 Mainshaft 11000 Crankshaft 11001 Crankarm 11002 Link Arm 11008 BH-1610 Roller Bearing (3) 11009 Pin - 1” dia. 11010 Carrier Cap 13244 Crank Retaining Ring (2) 13475 Journal Key 13685 1/4-20x5/8 BHCS 13738 #10 Washer 13895 10-24x3/8 BHCS Item A – Swage Rod Assembly Part # Description 13064 Swage Cover 1050 13417 Swage Connecting Rod 13522 Clevis Pin 13581 Grease Zerts 13840 Hair Pin Cotter 13896 1/4-20 3/8 BH Ejector Tab Screw 14517 Swage Station Bushing 20313 Swage Rod Assembly – Small: 13127 Swage Rod (1050) – Small 13245 Primer Swage Adjustment Bolt 13682 Swage Lock Nut 1050 20314 Swage Rod Assembly – Large: 13245 Primer Swage Adjustment Bolt 13364 Swage Rod (1050) – Large 13682 Swage Lock Nut 1050
29 Primer System Assembly - #20488 Upper Lower 1395713840 14037 13001 20488 1100317604 13844 13936 13746 20773 13363 13363 1299513130 - large 13222 - small 13423 14990 13858 13058 1360713296 12849 - large 13307 - small 20317 - small 20318 - large 22030 - small 22031 - large Upper Assembly Stock Description 13957 Magazine Shield Cap 20773 Primer Feed Body/Shield 22030 Primer Magazine Tube – Small 22031 Primer Magazine Tube – Large 20488 Primer Arm/Cam Assembly 11003 Slide Actuating Lever 13001 New Lever Arm Bracket 13746 Actuating Lever Cotter Pin 13840 Hair Pin Cotter 13844 Short Lever Spring 13936 Tab/Spring Arm Spring 14037 Clutch/Motor Bolt 17604 Bracket Pivot Pin Lower Assembly Stock Description 12849 1050 Primer Punch – Large 12995 Primer System Tappet 13058 Primer System Rocker Arm 13130 Primer Punch Bushing – Large 13222 Primer Punch Bushing – Small 13296 Primer System Rocker Bolt 13307 1050 Primer Punch – Small 13363 Primer Magazine Socket Bolt 13607 Rocker Bolt Lock Washer 13858 Primer Punch Spring 1050 20317 Primer Slide Assembly – Small 13423 Roll Pin – 1/8x5/8 14990 Slide Roll Pin Sleeve 20318 Primer Slide Assembly – Large 13423 Roll Pin – 1/8x5/8 14990 Slide Roll Pin Sleeve
30 Super 1050 Casefeeder Assembly HIGH OFF LO 13400 17808 13494 13859 13812 13540 1376113756 20641 13539 13205 1348413377 13685 12144 1365513238 See Page 31 Item A 13271 13655 13495 Stock # Description 12144 Bullet Bin Bracket 13205 Post Bolts 13238 Bin Bracket 13271 Post Stud 13377 Bin Bracket Mount Screw 13400 Casefeed Bowl 1050 13473 Casefeed Motor – 4 RPM (Not Shown) 13484 1050 Cartridge Bin 13494 Casefeed Funnel 13495 Lower Cord Clamp 13502 Clamp Retaining Screw 13539 Casefeed Cord Set 13540 Casefeed Motor Cover 13655 5/16 Washer 13688 Casefeed Funnel Baffle (9mm/.380/.38 Sup. Not Shown) 13756 Bullet Bin 13761 Casefeed Tube 1050 13779 Micro-Switch (Not Shown) 13812 Lighted Power Switch 13859 Casefeed Tube Clip 13895 10-24 BH Screw (Not Shown) 13954 Micro-Switch Mount Screw (Not Shown) 14022 Casefeed Motor Roll Pin (Not Shown) 14023 10-24 5/8 Buttonhead Screw (Not Shown) 14026 8-32x1/2 Bowl/Motor Screw (Not Shown) 17808 Casefeed Bowl Insert 20322 Casefeed Assembly 1050 (Large Pistol) 20324 Casefeed Assembly 1050 (Small Rifle) 20641 Casefeed Mounting Post Assembly 21079 Casefeed Assembly 1050 (Small Pistol)