Home > Dillon Precision > Firearms > Dillon Precision SL 900 Instruction Manual

Dillon Precision SL 900 Instruction Manual

Here you can view all the pages of manual Dillon Precision SL 900 Instruction Manual. The Dillon Precision manuals for Firearms are available online for free. You can easily download all the documents as PDF.

Page 11

12
Toolhead Assembly
1674116743
1674217351
16748 13896 1714116667167471257713989
17836
A-A
16668
17149
17148
17149
13742 167501675220782
17147
16744
16746
17477
16751Remington
 
 
14008
17899
17909
13895
Seat Plug Guide
16751 (black) Remington only
17836 (silver) A-A and Federal 

Page 12

13
Platform Assembly
16684
16683
13937
13738
14037 16697
17944
13789
16700
16701
1670217812
assembly
10716
138371763914574
13311
16695
16696
16694
16753 (3)
17126 (3)13891
14118
16699 1620914689 1468916692
16691
16693
17472 

Page 13

14
Primer Feed System Assembly & Installation
 
 
 

 
 

 
 

14026
16717 16713
16721
16723
17601
16714
140231713417354
1385617603 (3)
17474 (3)
16340
14026 16710
17472
17472
17472 13773
13773 16711 1480813923
13793
17132
14026
17472 

Page 14

15
Automatic Powder Measure Assembly
13882
Part # Description
13652 Powder Bar Part, Large
13691 Powder Measure Tube Only
13793 Roller
13799 Blue Wing Nut 
13801 Tinnerman Nut 
13845 Collar Sleeve
13848 Bellcrank Bushing
13853 Powder Bar Insert, Large
13858 Rod Compression Spring 
13871 Bellcrank Cube
13882 Powder Measure Lid
13893 Powder Bar Post, Large
13921 Powder Measure Plug
13939 Body Collar Clamp
13940 Connector Body Collar
13943 Powder Bar Bolt
13958 Powder Bar Bolt Washer     
14023 8-32 x 3/4...

Page 15

16
Shot Dispenser Assembly - # 22134, 12 gauge shown
17143
17142
14026
17146
13996
1381716739
16740
13958
16738
16726
16735
16736 16737 16740 14023 1373814808 169041379314041 138481672713871
16733
13989
13801 13799 138581673414041
13943 16725 17476
14013 1370117573 171391720217138 

Page 16

17
Finished Shotshell DimensionsWad Swing Arm Assembly
12 gauge shownHere are some dimensions of a typical 12ga. shotshell.
Always use a quality dial caliper when measuring your
shotshells. Length may vary dependent upon shotshell
manufacturer. Dimensions shown are for maximum,
uncrimped overall length. If you find it necessary to adjust
the collet size die, try to shoot for a middle of the road
measure of the brass base.
Wad Seated Depth
When developing loads for
shotshells be aware of your “wad
seated...

Page 17

Reloading ammunition and handling powder and
primers is inherently dangerous. Just as in shooting,
accidents do happen. These accidents are
nondiscriminatory; they happen to both the novice and
the experienced reloader. 
We have done everything we know how to make
your machine as safe as possible. We cannot, however,
guarantee your complete safety. To minimize your
risk, use common sense when reloading and follow
these basic rules:
Never operate the machine without ear and eye
protection on. Call our...

Page 18

round again so they won’t get stuck in the casefeed
tube (#16705). Returning the roller handle (#22183)
to its full aft position will advance the hull to station
two, where a new primer is inserted into the hull
when you push the roller handle (#22183) aft.
The automatic primer system holds 100 shotshell
primers. Every complete stroke of the roller handle
(#22183) will feed a primer to the hull. 
The automatic powder system is also located at
station two. The hopper holds one half pound of
powder and has...

Page 19

20
2. Lift the machine up and fasten the machine
securely to the forward edge of the bench. Fig. 3
3. Install the casefeed post (#17123) and the shot
post (#17124) to the frame of the machine using the
two long 4 1/2" bolts, 6 clamps (#13613), 2 - 1/4"
washers and 1/4-20 nuts. Fig. 4
4. Locate the shot container and place it on its
post. Fig. 55. Open the casefeeder box. Place the feeder on
your bench and plug it into a 110v AC outlet (220v
for European casefeeders). Place a handful of empty...

Page 20

Be sure to secure the small, but important, screw
located at the rear of the bowl at the base. This little
screw (#13685) secures the entire bowl assembly to
the casefeed post (17123). Fig. 8
7. The powder measure (#20782) is the next item
we’ll be installing on the machine. Familiarize
yourself with its operation – every complete stroke
of the powder bar dispenses one charge of powder.
The dispenser is hull activated. 
Using a 7/16” wrench, rotate the bolt located on
the end of the powder bar –...
Start reading Dillon Precision SL 900 Instruction Manual

Related Manuals for Dillon Precision SL 900 Instruction Manual

All Dillon Precision manuals