Digital Projection Titan Hd-500, Hd-250 User Manual

Rev B  02/2007 Page 4.35
Digital Projection TITAN HD-500, HD-250 User Manual  4. Controlling the projector
Lamp
Press  and   to select Lamp.
 Press 
 to open the Lamp submenu.
The middle row shows the current lamp setting.
Change Lamp Setting
Press  and   to select Change Lamp Setting.
Press 
 to open the Lamp Setting control box. •
•
Notes
Setup Menu
 Lamp Setup menu, continued
continued 

Page 4.36 Rev B  02/2007
4. Controlling the projector  Digital Projection TITAN HD-500, HD-250 User Manual
Notes
  In single lamp modes:
  - if the running lamp fails, the 
other lamp will automatically be 
switched on.
 The Lamp 2 and Alternate 
settings apply only to the HD-
500. The HD-250 has only one 
lamp.
  The selected lamp mode:
  - will not be applied until OK is 
selected
  - will be applied gradually over a 
period of 30 seconds
  - will not be applied until the end 
of any warm-up or...

Rev B  02/2007 Page 4.37
Digital Projection TITAN HD-500, HD-250 User Manual  4. Controlling the projector
Notes
Setup Menu
  On Screen Display
 The On Screen Display will 
move to the centre of the DMD 
when Blanking is turned On.
 (see Geometry menu, earlier in 
this section).
  If a menu is opened, and no 
other key is pressed within the 
period set in the OSD Timeout 
menu, then the menus will 
disappear. When the  
 key 
is pressed again, the menus will 
reopen at the same point they 
were last...

Page 4.38 Rev B  02/2007
4. Controlling the projector  Digital Projection TITAN HD-500, HD-250 User Manual
Password
Entry to the password protected area is available to authorised service personel 
only.
Press 
 and   to select Password.
 Press 
 to open the Password control box.
Press 
 and   to select each digit in turn.
 Press 
 and   to adjust the digit from:
0 to 9
 then move to the next digit.
 Use 
 and   to select from
OK
 Press   
 to enter the password controlled area.
or Cancel
Press  
 or...

Rev B  02/2007 Page 4.39
Digital Projection TITAN HD-500, HD-250 User Manual  4. Controlling the projector
Notes
Setup Menu
 Comunication
  When fresh batteries are 
inserted in the remote control, 
it will default to address 00. 
Remote control 00 is a master 
control,  able to control all 
projectors.
  FIf two or more projectors are 
set to the same address, they 
can be controlled from one 
remote control, provided they 
are connected by cable or in 
range of the infra red.
Communication
Press  and...

Page 4.40 Rev B  02/2007
4. Controlling the projector  Digital Projection TITAN HD-500, HD-250 User Manual
Notes
Setup Menu
 Network
  Some items may be greyed out 
or not editable, due to the effect 
of other settings made in the 
Network submenu.
  For example, if a Wired 
Connection is selected:
 Wifi , Channel and SSID will be 
unavailable.
Setup menu continued
Network
Press  and   to select Network.
 Press 
 to open the Network submenu.
LAN MAC Address
Projector’s unique ID  - for information only -...

Rev B  02/2007 Page 4.41
Digital Projection TITAN HD-500, HD-250 User Manual  4. Controlling the projector
Notes
 LAN IP Address cannot be 
changed if DHCP is set to ON.
  DHCP will set the the address, 
which will be displayed for 
information only.
Setup menu, Network continued
DHCP
Press  and   to select DHCP
 Press 
 to open the DHCP control box.
 Press 
 and   to select from:
On
Off
 Press   
 to apply the new DHCP setting.
LAN IP Address
Press  and   to select LAN IP Address
 Press 
 to open the...

Page 4.42 Rev B  02/2007
4. Controlling the projector  Digital Projection TITAN HD-500, HD-250 User Manual
Notes
 LAN IP Subnet cannot be 
changed if DHCP is set to ON.
  DHCP will set the the subnet 
mask, which will be displayed 
for information only.
LAN Subnet Mask
Press  and   to select LAN Subnet
 Press 
 to open the LAN Subnet control box.
 Press 
 and   to select from:
Automatic
or one of the following:
Class C Masks
255.255.255.254
255.255.255.252
255.255.255.248
255.255.255.240
255.255.255.224...

Rev B  02/2007 Page 4.43
Digital Projection TITAN HD-500, HD-250 User Manual  4. Controlling the projector
LAN Gateway Mask
Press  and   to select LAN Gateway
Press 
 to open the LAN IP Address control box.
Use 
 and   to select each number in turn.
Use 
 and   to adjust the number
then move to the next number.
Use 
 and   to select from
Apply
Cancel
Press  
 to apply the new LAN Gateway Mask, or to exit without making the 
change. •
Setup menu, Network continued
Notes
 LAN IP Gateway cannot be 
changed...

Page 4.44 Rev B  02/2007
4. Controlling the projector  Digital Projection TITAN HD-500, HD-250 User Manual
Channel
Press  and   to select Channel.
 Press 
 to open the Channel control box.
 Press 
 and   to select the channel number.
 Use 
 and   to adjust the channel number from:
0 to 14
 Use 
 and   to select from
 Apply
 Press   
 to apply the new Channel number.
or Cancel
Press  
 or   to exit without making the change.
SSID
Projector’s ID  - for information only. •
•
Setup menu, Network continued...