Digital Projection Titan Hd-500, Hd-250 User Manual

Rev B  02/2007 Page 2.19
Digital Projection TITAN HD-500, HD-250 User Manual  2. Installation
Notes
  For more information about pin 
connections and control codes 
see section 7. Appendix.
  For more information about 
using a browser to control the 
projector see section 4. Using 
the menus.
ComputerNull-modem  
cableTITAN
Control connection examples
LAN connection
All of the projector’s features can be controlled via a LAN connection, using a 
standard internet browser package such as Internet...

Page 2.20 Rev B  02/2007
2. Installation  Digital Projection TITAN HD-500, HD-250 User Manual
Notes
  Use only the power cable 
provided.
  Ensure that the power 
outlet includes a Ground 
connection, as this 
equipment MUST be earthed.
  Handle the power cable 
carefully and avoid sharp 
bends. Do not use a damaged 
power cable.
Power connection
When mains power is fi rst applied, the projector will perform a self-test, then go into 
Standby mode.
The Power indicator on the control panel will show amber...

Rev B  02/2007  Page 3.1
3. Getting Started
Contents
Switching the projector on ............................................................................................................... 3.2
Selecting an input or test pattern ................................................................................................... 3.2
Input ................................................................................................................................................ 3.2
Test pattern...

Page 3.2 Rev B  02/2007
3. Getting Started  Digital Projection TITAN HD-500, HD-250 User Manual
Selecting an input or test pattern
Input
Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI
4. (not used in this projector)
5. Composite Video
6. S-Video
7. Component
Or press the numbered keys 1–7 to change directly to the input:
Test pattern
 If you have no video source connected to the projector, then you can display a test 
pattern as follows:
Press 
 on the...

Rev B  02/2007 Page 3.3
Digital Projection TITAN HD-500, HD-250 User Manual  3. Getting Started
Notes
  For more detailed information 
about:
  - using the control keys on the 
remote control or keypad,
  - using the menus,
  see the next section: 
Controlling the projector.
  When any of the three Lens 
adjustment keys is pressed, the 
blue Transmit indicator on the 
remote control will light for 10 
seconds:
  - after 10 seconds, if no 
adjustment has been made, 
the indicator will go out and 
the Lens...

Page 3.4 Rev B  02/2007
3. Getting Started  Digital Projection TITAN HD-500, HD-250 User Manual
Adjusting the projected image
Picture settings
Press a  key, followed by  and   to adjust these picture settings:
 Brightness   
 BRI
Contrast  
 CON
Saturation  
 SAT
Phase  
 PHASE
Aspect ratio   
 ASPECT
Geometry settings
Press Keystone  KEYST
followed by 
 and  to adjust the keystone correction.
Press Position  
 POS  (for all inputs except DVI)
followed by 
, ,  and  to adjust the picture position, for...

Rev B  02/2007  Page 4.1
4. Controlling the projector
Contents
Overview ............................................................................................................................................... 4.4
Controlling the projector..................................................................................................................... 4.4
Input modes and settings ......................................................................................................................

Page 4.2 Rev B  02/2007
4. Controlling the projector  Digital Projection TITAN HD-500, HD-250 User Manual
Using the menus ............................................................................................................................... 4.15
Navigating menus and submenus ..................................................................................................... 4.15
Menu controls...

Rev B  02/2007 Page 4.3
Digital Projection TITAN HD-500, HD-250 User Manual  4. Controlling the projector
Setup menu ........................................................................................................................................ 4.30
Projector ........................................................................................................................................ 4.31
Orientation...

Page 4.4 Rev B  02/2007
4. Controlling the projector  Digital Projection TITAN HD-500, HD-250 User Manual
Overview
Controlling the projector
The projector can be controlled from:
the remote control
the keypad
the RS232 input
the Ethernet input
For more information about controlling the projector using the RS232 and 
Ethernet inputs, see Remote communications protocol in section 7. 
Appendix.
For information about how to connect the projector, see Connecting the 
projector in section 2. Installation, and...