Digital Projection Titan 1080p 500/250, Sx+-500, Hd 500/250, Xg 500 User Manual

							
Rev B    01/2007    page 1
TITAN 1080p 500/250, sx+-500, HD 500/250, XG 500
105-924B
page 3Super High Brightness Digital Video Projector
Important Information
seite 10 Super High Brightness Digit aler Videoprojektor
Wichtige Informationen
page 17 Vidéo projecteur numérique à forte luminosité
Informations import antes
página 24 Vídeo-proyector digital de alta luminosidad
Información import ante
pagina 31 Proiettore video digitale ad alta luminosità
Informazioni import anti
sid. 38 Digital videoprojektor Super High Brightness
Viktig information 
						

							
Rev B    01/2007    page 2
EnglishDigital Projection  TITAN 1080p 500/250, sx+-500, HD 500/250, XG 500
Digital Projection
Digital Projection Limited,
Greenside Way,  Middleton, Manchester M24 1XX, UK.
Registered in England No. 2207264, Registered Office: as above
Tel +44 (0) 161 947 3300
Fax +44 (0) 161 684 7674
Email enquiries@digit alprojection.co.uk, service@digit alprojection.co.uk
Web Site www.digitalprojection.co.uk
Digital Projection Inc.
55 Chastain Road, Suite 115,  Kennesaw, GA 30144. USA
Tel (USA) 770 420 1350
Fax (USA) 770 420 1360
Email   [email protected]
Web Site www.digitalprojection.com 
						

							
Rev B    01/2007    page 3
EnglishDigital Projection  TITAN 1080p 500/250, sx+-500, HD 500/250, XG 500
This information booklet contains the following extracts from the User M\
anual:
Contents
Symbols used in the  User Manual........................................................................\
........... 2
Declaration of Conformity ........................................................................\
........................ 3
General precautions ........................................................................\
................................. 4
Installation precautions ........................................................................\
............................ 5
Operation and configuration  precautions ...................................................................... 6
Compliance with international standards ....................................................................... 6
Noise ........................................................................\
.................................................. ...................... 6
RF Interference ........................................................................\
........................................ ............... 6
Specifications ........................................................................\
......................................... ... 7Part numbers........................................................................\
........................................... ............... 7
Optical ........................................................................\
................................................ ..................... 7
Electrical ........................................................................\
............................................. .................... 8
Physical ........................................................................\
............................................... .................... 8
Full information about operating, connecting and setting up the projecto\
r can be found in the
User Manual, located on the CD.
Symbols used in the User Manual
ELECTRICAL W ARNING: this symbol indicates that there is a danger of electrical shock\
unless the instructions are closely followed.
WARNING: this symbol indicates that there is a danger of physical injury \
to yourself
and/or damage to the equipment unless the instructions are closely follo\
wed.
NOTE: this symbol indicates that there is some important information tha\
t you should read. 
						

							
Rev B    01/2007    page 4
Digital Projection TITAN 1080p 500/250, sx+-500, HD 500/250, XG 500 English
Declaration of Conformity
Directives covered by this Declaration89/336/EEC Electromagnetic Compatibility Directive, amended by 92/31/EEC\
 and 93/68/EEC.
73/23/EEC Low Volt age Equipment Directive, amended by 93/68/EEC.
Products covered by this Declaration
Large screen video projector type The CE mark was first applied in:
TITAN sx+-500 June 2006
TITAN HD 500 July 2006
TITAN HD 250 July 2006
TITAN XG 500 July 2006
TITAN 1080p 500 April 2007
TITAN 1080p 250 April 2007
Basis on which Conformity is being declaredThe products identified above comply with the protection requirement s of the above EU directives, and
the manufacturer has applied the following standards.
EN 55022:1998 - Limits and Methods  of Measurement of Radio Disturbance Characteristics of
Information Technology Equipment.
EN 55024:1998 - Limits and Methods  of Measurement of Immunity Characteristics of Information
Technology Equipment.
EN 55103:1997 - Product family  Standard for Audio, Video, Audio-V isual and Entert ainment
Lighting Control apparatus for Professional Use.
EN 60950:2000- S pecification for Safety of Information  Technology Equipment, including Electrical
Business equipment.
The technical documentation required to demonstrate that the products meet the requirements of the
Low Volt age directive  has been compiled by the signatory below and is available for inspection\
 by the
relevant enforcement authorities.
Signed:
Authority: D.J. Quinn,  Product Development Director
Date: 28 July 2006
Attention!The attention of the specifier, purchaser, installer, or user is drawn to special measures and limit ations
to use which must be observed when these products  are taken into service to  maintain compliance
with the above directives. Details of these special measures are availab\
le on request, and are also
contained in the product manuals. 
						

							
Rev B    01/2007    page 5
EnglishDigital Projection  TITAN 1080p 500/250, sx+-500, HD 500/250, XG 500
General precautions
Do not open the cabinet. There are no user serviceable parts inside.
Use only the power cable provided.
Ensure that the power outlet includes a Ground connection, as this equip\
ment MUST be
earthed.
Take care to prevent small objects such as  paper or wire from falling into the projector.
If this does happen, switch off immediately, and have the object s removed by authorised
service personnel.
Do not expose the projector to rain or moisture, and do not place any li\
quids on top of
the projector.
Unplug before cleaning, and use a damp, not wet, cloth.
Do not touch the power plug with wet hands.
Do not touch the power plug during a thunder storm.
Handle the power cable carefully and avoid sharp bends. Do not use a dam\
aged power
cable.
There are no user-serviceable parts inside the lamp module. The whole module should
be replaced.
Take care when removing the lamp module.
NEVER touch the lamp or reflector.
Take care not to touch the glass surface of the lamp module. If you do ac\
cident ally
touch the glass, it should be cleaned before use. (see section 5. Maint\
enance.)
Do not use the lamp for more than 1500 hours, as this may cause serious \
lamp failure,
damage the lamp module and cause extra cost on replacement.
HID lamps  produce high intensity light. Do not look directly at the light coming f\
rom the
lamp housing, or the lens, or allow items such as magnifying lenses to b\
e placed in the
light path. This could result in serious eye damage.
Do not touch the ventilation outlets, as they will become hot in use.
Do not cover or obstruct the ventilation outlets or inlets.
Do not cover the lens whilst the projector is switched on. This could ca\
use a fire
Always allow the projector to cool for 5 minutes before disconnecting th\
e power,
moving the projector or changing the lamp.
Never use strong detergents or solvents  such as alcohol or thinners to clean the
projector and lens. 
						

							
Rev B    01/2007    page 6
Digital Projection TITAN 1080p 500/250, sx+-500, HD 500/250, XG 500 English
Installation precautions
Connect the LAN cable only to a computer LAN connection. Other similar c\
onnectors
may have a dangerously high voltage source.
The projector must be installed only by suitably qualified personnel, in\
 accordance with
local building codes.
The projector should be installed as close to the power outlet as possib\
le.
The power connection should be easily accessible, so that it can be disc\
onnected in an
emergency.
Ensure that there is at least 30cm (12in) of space between the ventila\
tion outlets and
any wall, and 10cm (4in) on all other sides.
Do not install the  projector close to anything that might  be affected by it s operational
heat, for instance, polystyrene ceiling tiles, curtains etc.
The projector weighs approximately 27 kg (50 lbs). Use safe handling t\
echniques when
lifting the projector.
When stacking projectors, the stack MUST be vertical, to ensure that the\
 stresses are
distributed to all frame couplings.
Before inst allation, make sure that the surface, ceiling or rigging that is to supp\
ort the
projector is capable of supporting the combined  weight of the projector and lens (see
specification for exact weights).
Separate backup safety chains or wires should always be used for each proje\
ctor.
Do not place heavy objects on top of the projector chassis. Only the cha\
ssis corners
and the rigging frame are capable of withstanding the weight of another \
projector.
Do not st ack more than 3 projectors.
Do not drop or jarr the projector.
1080p, sx+500: The lens release lever should always be set to the locked\
 position to
prevent the lens from falling out.
Place the projector in a dry area away from sources of dust, moisture, s\
team, smoke,
sunlight or heat.
Do not tilt the projector more than  ±12° from side to side when i\
n use, as this may
cause serious lamp failure, damage the lamp
module and cause extra cost on replacement.
The projector my be tilted forwards and
backwards as necessary.
±12° 360° 
						

							
Rev B    01/2007    page 7
EnglishDigital Projection  TITAN 1080p 500/250, sx+-500, HD 500/250, XG 500
Operation and configuration precautions
Do not make changes to the networking configuration unless you understan\
d what you
are doing, or have taken advice from your Network Manager. If you make a\
 mistake, it is
possible that you will lose contact  with the projector. Always double-check your
settings before pressing the  APPLY button.  Always keep a written note of the original
settings, and any changes you have made.
Software update  should NOT be carried out except by, or with the supervision of, Digital
Projection Service personnel.
Compliance with international  standards
NoiseGSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 70 dB (A) according to ISO 3744 \
or ISO 7779.
RF Interference
FCC
The Federal Communications Commission does not allow any modifications o\
r changes to the unit
EXCEPT those specified by Digit al Projection in this manual. Failure to comply with this government
regulation could void your right to operate this equipment.
This equipment has been tested and found to comply with the limits for a\
 Class B digital device,
pursuant to Part 15 of the  FCC Rules. These limits are  designed to provide reasonable protection
against harmful interference in a residential inst allation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accorda\
nce with the instructions, may
cause harmful interference to radio communications. However, there is no\
 guarantee that interference
will not occur in a particular installation. If this equipment does caus\
e harmful interference to radio or
television reception, which can be determined by turning the equipment o\
ff and on, the user is
encouraged to try to correct the interference by one of the following me\
asures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject\
 to the following two
conditions: (1)  This device  may not cause harmful interference, and (2) this device must accept an\
y
interference received, including interference that may cause undesired o\
peration.
This equipment contains an FCC approved RF transmitter module with FCC I\
D: R68WIPORT.
European Waste  Electrical and Electronic Equipment (WEEE) DirectiveDigital Projection Ltd is fully committed to minimising Waste Electrical and Electronic
Equipment. Our products are designed with reuse, recycling and recovery of all components
in mind. To this end, at end of life, your projector may be returned to Digital Pr\
ojection Ltd or
its agent so that the environmental imp act can be minimised. 
						

							
Rev B    01/2007    page 8
Digital Projection TITAN 1080p 500/250, sx+-500, HD 500/250, XG 500 English
Specifications
Part numbers
Projector1080p 250: 106-242,  sx+ 500: 105-925,   HD 500: 105-948,
XG 500:  106-239,   1080p 500:  106-241,  HD-250: 106-240
Power cable 10A, Europe 102-163United Kingdom 102-180
Power cable 13A,  North America 102-165 Rigging frame104-923
Remote control 105-023 4x AAA batteries105-922
Remote cable 5m 102-162
User manual on CD 105-923C Important Information 105-924B
Replacement parts
Lamp module 001-742 Air filter102-064
Lenses sx+ 500
0.73 : 1  fixed lens 105-607
1.2 : 1 fixed lens  (3 - 15m) 105-608
1.2 : 1 fixed lens  (1.2 - 2.0m) 105-609
1.5 - 2.02 :  1 zoom lens 105-610
2.02 - 2.77 : 1 zoom lens 105-611
2.77 - 4.51 :  1 zoom lens 105-612
4.51 - 7.53 :  1 zoom lens 105-613
Lenses XG 500
0.8 : 1  fixed lens 001-734
1.2 : 1  fixed lens 001-735
1.5 - 1.8 :  1 zoom lens 001-736
1.8 - 2.25 :  1 zoom lens 001-737
2.25 - 3.0 :  1 zoom lens 001-738
3.0 - 4.5 :  1 zoom lens 001-739
4.5 - 7.0 :  1 zoom lens 001-740
Lenses HD 500/250 High  BrightnessHigh Contrast
0.63 : 1 fixed  lens 001-734 102-373
0.96 : 1 fixed  lens 001-735 102-835
1.2 - 1.44 : 1 zoom lens 001-736 102-374
1.44 - 1.8 : 1 zoom lens 001-737 102-375
1.8 - 2.4 : 1  zoom lens 001-738 102-376
2.4 - 3.6 : 1  zoom lens 001-739 102-377
3.6 - 5.6 : 1  zoom lens 001-740 102-378 Lenses 1080p 500/250
0.67 : 1 
fixed lens 105-607
1.12 : 1 fixed lens  (3 - 15m) 105-608
1.12 : 1 zoom lens  (1.2 - 2m) 105-609
1.39 - 1.87 :  1 zoom lens 105-610
1.87 - 2.56 : 1 zoom lens 105-611
2.56 - 4.16 :  1 zoom lens 105-612
4.16 - 6.96 :  1 zoom lens 105-613
Optical
Digital Light Processor 1080p 500/250: 3 x 0.95” Texas Instruments  DMD™,
resolution 1920 x 1080 pixels
sx+ 500:  3 x 0.94”  Texas Instruments  DMD™,
resolution 1400 x 1050 pixels
HD 500/250:  3 x 0.8” Texas Instrument s DMD™,
resolution 1280  x 720 pixels
XG 500:  3 x 0.7” T exas Instrument s DMD™,
resolution 1024 x 768 pixels 
						

							
Rev B    01/2007    page 9
EnglishDigital Projection  TITAN 1080p 500/250, sx+-500, HD 500/250, XG 500
Contrast Ratio 1080p 500: >2000:1 250: >5000:1 full field (±10%)
sx+ 500:  >1600:1 full field (±10%)
HD 500:  >1200:1 full field (±10%) (High Brightness lens)
HD 250:  >4000:1 full field (±10%) (High Contrast lens)
XG 500:  >1200:1 full field (±10%)
Pixel fill factor 87%
Lamp power 500: 2 x 250W,   250: 1 x 250W
Lamp life (typical) 1500 hours  in dual lamp mode (500 only),
3000 in single lamp mode
Brightness 1080p 500: 6000 ANSI lumens (±10%)  in dual lamp mode
1080p 250:  2000 ANSI  lumens (±10%)
sx+ 500:  5500 ANSI lumens (±10%)  in dual lamp mode
HD 500:  4500 ANSI lumens dual lamp (High Brightness lens)
HD 250:  1600 ANSI lumens (±10%) (High Contrast lens)
XG 500:   4500 ANSI lumens (±10%) in dual lamp mode
Colour temperature Native: 7500°K (±1000°K), White balance adjustment: 3000°K - 10000°K
ElectricalInputs RGB1,  RGB2, DVI, Composite Video, S-Video, Component
1080p 500, 1080p 250, sx+ 500:  and SDI
Pixel clock up to 165MHz
Control input s 1 x LAN 1 x wifi LAN (FCC ID: R68WIPORT )
1 x RS232 serial: 19200 baud, 8 bits, 1 stop bit, no parity
1 x remote control
Mains voltage 100-230 VAC ±10%, 48-62Hz (single phase)
Power consumption 500: 750 W,   250: 500W
International Regulations Meets FCC Class B  requirements
Meets  EMC Directives (EN 50081-1, EN 50082-1, EN 55022)
Meets  Low Volt age Directive (EN60950)
Indicators Power,  Shutter, Error, IR, Lamp 1, Lamp 2 (500 only)
PhysicalOperating T emperature 0  to 40°C
Storage Temperature -10 to 50°C
Thermal Dissip ation 500: 2600 BTU/hr,   250: 1733 BTU/hr
Operating Humidity 20%  to 80% non-condensing
W eight approximately 27 kg (60 lbs)
FCC WIFI ID,  R68WIPORT 
						

							
Rev B    01/2007    page 10
Digital Projection TITAN 1080p 500/250, sx+-500, HD 500/250, XG 500 Deutsche
Dieses Informationsheft enthält die  folgenden Auszüge aus dem Benutzerhandbuch:
Inhalt
Symbol in diesem Leitfaden ........................................................................\
..................... 9
Konformitätserklärung ........................................................................\
........................... 10
Allgemeine Vorsichtsmaßnahmen ........................................................................\
......... 11
Vorsichtsmaßnahmen bei der  Installation.................................................................... 12
Vorsichtsmaßnahmen bei Betrieb und Konfiguration ................................................. 13
Übereinstimmung mit internationalen Standards ........................................................ 13
Lärm ........................................................................\
....................................................... ................ 13
Funkstörung ........................................................................\
............................................ .............. 13
Technische Daten........................................................................\
.................................... 14Teilenummern........................................................................\
........................................... ............ 14
Optisch ........................................................................\
................................................ .................. 14
Elektrisch ........................................................................\
............................................. ................. 15
Physisch ........................................................................\
............................................... ................. 15
Vollständige Informationen über den Betrieb, den Anschluss und die Einstellungen des
Projektors finden Sie im Benutzerhandbuch auf der CD.
Symbol in diesem  Leitfaden
ELEKTRISCHE  WARNUNG: Dieses Symbol  weist darauf hin, dass Stromschlaggefahr
besteht, wenn die Anweisungen nicht strikt befolgt werden.
WARNUNG: Dieses Symbol weist darauf hin, dass die Gefahr von Körper- u\
nd
Sachschäden besteht, wenn die Anweisungen nicht strikt befolgt werden.
HINWEIS: Dieses Symbol weist auf wichtige Informationen hin, die Sie les\
en sollten.