Digital Projection Thunder 10000sx User Manual

E – 5
1. INPUT 3 RGB Connector (Mini D-Sub 15 pin)
Connect your PC or other analog RGB equipment such as a high-defi-
nition document camera.
This connector accepts RGB signals only.
Not compatible with component signals.
2. Option Connector (Mini D-Sub 9 pin)
For system expansion such as PC-control.
IN ................. connect to the external equipment such as PC or Third Party
Control System.
OUT ............. for daisy-chaining multiple projectors and operating them with
the same external equipment....

E – 6
ENTER
CANCEL UNDOAUTOHELP ON
TEST
ABC1DEF2GHI3
JKL4MNO5PQR6
STU7VWX8
0YZ /9 POWER INPUT
OFF
INFO
PIXEL SOUNDOSD
MAGNIFY/
CTL
FOCUS  +
-
ZOOM  +
MENU/ADDRESS
IMAGE/PROJECTOR
POSI/LENS
KEY ST./
ON
OFF
RE-LIST/ PICTURE
ADJUST
WHITE BAL.
BAMP/G
PICT/SHUT
-
MUTE
2
13
28
8
7
6
22
21
15
17
16
3
10
11
262
7
9
23
14
12
19
18
20
5
4
25
24 1
Remote Control
1 POWER ON
Press to turn on the projector. The POWER indicator lights up green.
2 POWER OFF
Press and hold this button for a minimum of two seconds to turn...

E – 7
19 MUTE OSD
Press to turn off the on-screen display. Press again to restore the on-
screen display.
NOTE: You can also turn off the on-screen display by pressing and holding CTL
and then pressing MUTE OSD; doing this again restores it. In this case any
adjustment will still change the projectors memory settings. This mode is avail-
able even when an input is switched to another or the power is turned off using
the POWER OFF button on the remote control.
20 MUTE PICTURE
Press to turn off the picture...

E – 8
2. INSTALLATION
Formulas: Screen Width H (5:4) (m) = Screen Height V x 5/4 x 0.0254
Screen Height V (5:4) (m) = Screen Width H x 4/5 x 0.0254
Screen Diagonal (5:4) (m) = Screen Height V x 6.4/4 x 0.0254
Screen Width H (5:4) (inch) = Screen Height V x 5/4
Screen Height V (5:4) (inch) = Screen Width H x 4/5
Screen Diagonal (5:4) (inch) = Screen Height V x 6.4/4
Width (H)
1.6(63)
1.9(75)
2.3(90)
2.9(112.5)
3.4(135)
4.0(157.5)
4.6(180)
5.1(202.5)
5.7(225)
6.7(262.5)
7.6(300)
8.6(337.5)
9.5(375)Height...

E – 9
Lens Shift Adjustable Range
Lens Shift Adjustable Range for Desktop and Ceiling Mount Application
The diagram below shows the location of the image position in the lens. The lens can be shifted within the shaded area as shown using the normal
projection position as a starting point.
Maximum Possible Range for TL-1ZH, TL-2Z and TL-4Z
Parenthesized values for the ceiling mount application
Up: 0.41 V (0.24 V) Right: 0.28 H (0.19 H)
Down: 0.24 V (0.41 V) Left: 0.19 H (0.28 H)
(H: width of projected...

E – 10
Selecting A Location
The fur ther your projector is from the screen or wall, the larger the im-
age. The minimum size the image can be projected is 80 (2 m) mea-
sured diagonally. The largest the image can be is 500 (12.7 m).
WARNING
•Only use your projector on a solid, level surface. If the projector falls
to the ground, you can be injured and the projector severely dam-
aged.
•Do not use the projector where temperatures vary greatly. The pro-
jector must be used at temperatures between 40...

E – 11
Connecting the Power Cable and Turning on the Projector
Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed.
1. Connect the supplied power cable to the projector.
Plug the supplied power cable into the AC outlet.
3. SETUP
2. Turn On The Projector
The main power switch is on the front panel of the projector.
By pushing up this switch, the projector will go into its standby mode and the POWER
indicator will glow orange. Only...

E – 12
About Startup Screen
(Menu Language Select screen)
When you first turn on the projector, you will get the Startup screen.
This screen gives you the oppor tunity to select one of the seven menu languages: English, German,
French, Italian, Spanish,Swedish and Japanese.
To select a menu language, follow these steps:
1. Use the Select ▲ or ▼ button to select one of the seven languages for the menu.
2. Press the Enter button to execute the selection.
3. The Basic/Custom menu will be displayed in the...

E – 13
Set up the projector
1. Turn on the projector
2. Select your type of projection:
Desktop front, ceiling rear, desktop rear, and ceiling front.
3. Display the test pattern by pressing the TEST button on the re-
mote control or using the menu.
TEST
4. Adjust the image position and the image size.
(1) Press and hold the CTL button and press the POSITION button to display
the Lens Shift adjustment screen.
Use the Select button on the remote control or the LENS SHIFT button on
the projector cabinet to...

E – 14
Keystone
Keystone distortion
Normal
Keystone is the distortion of a projected image that usually creates a
wider top than bottom. Aiming a projector upward on a wall rather than
straight at a wall creates this distortion. Use the 

 or  buttons on the
slide bar to correct this keystone (trapezoidal) distortion.
NOTE: The keystone feature is not available when the test pattern or the bluebackground is displayed.
NOTE: With the projector aimed directly at the screen the maximum keystoneangle that...