Digital Projection Thunder 10000sx User Manual

							THUNDER 10000sx
Super High Brightness Digital Video Projector
User Manual 
						

							E – ii
CAUTION: To turn off the main power, be sure to remove the plug
from power outlet. The power outlet socket should be installed as
near to the equipment as possible, and should be easily accessible.
3. GSGV Acoustic Noise Information Ordinance:
The sound pressure level is less than 70 dB(A) according to ISO 3744
or ISO 7779.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS
UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEP-
TACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE
FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS
THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
AVERTISSEMENT
POUR EVITER UN FEU OU UN RISQUE D’ELECTROCUTION
NE PAS EXPOSER CET ENSEMBLE A LA PLUIE OU A
L’HUMIDITE; DE MEME, NE PAS BRANCHER LA PRISE POLAIRE
AVEC UNE RALLONGE A MOINS QUE LES DENTS DE LA PRE-
MIERE NE S’Y INSERENT PLEINEMENT.
EVITER D’OUVRIR LE COFFRET CAR IL Y A, A L’INTERIEUR,
DES COMPOSANTS SOUMIS A UNE HAUTE-TENSION; POUR
LES REPARATIONS, S’ADRESSER A UN PERSONNEL
QUALIFIE.
* In order to reduce any interference with radio and television reception use a signal cable with ferrite core attached.
Use of signal cables without a ferrite core attached may cause interference with radio and television reception.
*This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to  Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the installation manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CAUTION
RISK OF ELECTRIC SHOCK
 DO NOT OPENRISQUE D’ELECTROCUTION
NE PAS OUVRIR
ATTENTION
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
OPEN COVER. NO USER-SERVICEABLE PARTS IN-
SIDE. REFER SERVICING  TO QUALIFIED SERVICE
PERSONNEL.
This symbol warns the user that uninsulated voltage
within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any
kind of contact with any part inside of this unit.
This symbol alerts the user that important literature
concerning the operation and maintenance of this unit
has been included. Therefore, it should be read carefully
in order to avoid any problems.
DOC compliance Notice
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.ATTENTION:
POUR EVITER LES RISQUES D’ELECTROCUTION, NE
PAS OUVRIR LE COUVERCLE. AUCUN DES ELEMENTS
INTERNES NE DOIT ETRE REPARE PAR L’UTILISATEUR.
NE CONFIER L’ENTRETIEN QU’A UN PERSONNEL
QUALIFIE.
L’éclair fléché dans un triangle équilatéral est destiné à
avertir l’utilisateur de la présence, dans l’appareil, d’une
zone non-isolée soumise à une haute-tension dont
l’intensité est suffisante pour constituer un risque
d’electrocution.
Le point d’exclamation dans un triangle équilatéral est
destiné à attirer l’attention de l’utilisateur sur la présence
d’informations de fonctionnement et d’entretien
importantes dans la brochure dccompagnant l’appareil.
DOC avis de conformation
Cet appareil numérique de la classe A respecte toutes les exigences
du Réglement sur le Matériel D’interférence du Canada.
Precautions: Please read this manual carefully before using your
DIGITAL PROJECTION 10000sx Projector and keep the manual
handy for future reference.
WARNING
This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
CAUTION 
						

							E – iii
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unob-
structed to prevent potentially dangerous concentrations of ozone
and the build-up of heat inside your projector. Allow at least 8 inches
(20cm) of space between your projector and a wall. Allow at least 20
inches (50 cm) of space between the ventilation outlet and object.
2. Prevent foreign objects such as paper clips and bits of paper from
falling into your projector. Do not attempt to retrieve any objects that
might fall into your projector. Do not insert any metal objects such as
a wire or screwdriver into your projector. If something should fall into
your projector, disconnect it immediately and have the object removed
by a qualified your service person.
3. Do not place any liquids on top of your projector.
CAUTION: High Pressure Lamp May Explode if Improperly Handled.
Refer Servicing to Qualified Service Personnel.
Lamp Caution:  Please read before operation
Due to the lamp being sealed in a pressurized environment, there is
a small risk of explosion, if not operated correctly.  There is minimal
risk involved, if the unit is in proper working order, but if damaged or
operated beyond the recommended 750 hours, the risk of explosion
increases.
Please note that there is a warning system built in, that displays the
following message when you reach 750 hours of operation”  Lamp
Running Time is Over 750 Hours!!”  When you see this message
please contact your DIGITAL PROJECTION Dealer for a replacement.
If the lamp does explode, smoke will be discharged from the vents
located on the side of the unit.  This smoke is comprised of  glass in
particulate form and Xenon gas,  and will not cause harm if kept out
of your eyes.  If your eyes have been exposed to this gas, please
flush your eyes out with water immediately and seek immediate
medical attention.   Do not rub your eyes!  This could cause seri-
ous injury.
WARNING: Do not look into the lens while the projector is on. Seri-
ous damage to your eyes could result.
CAUTION
Do not unplug the power cable from the wall outlet under any one of
the following circumstances. Doing so can cause damage to the
projector:
•While the message Please wait a moment appears. This mes-
sage will be displayed after the projector is turned off.
•Immediately after the power cable is plugged into the wall outlet
(the POWER indicator has not changed to a steady orange glow).
•Immediately after the cooling fan stops working (After the projec-
tor is turned off with the POWER OFF button the cooling fan con-
tinues to work for 3 minutes while the Two Digit INDICATOR --
flashes).
Important Safeguards
These safety instructions are to ensure the long life of your projector
and to prevent fire and shock. Please read them carefully and heed all
warnings.
Installation
1. Place the projector on a flat, level surface and in a dry area free from
dust and moisture.
2. Do not place the projector in direct sunlight, near heaters or heat
radiating appliances.
3. Exposure to direct sunlight, smoke or steam could harm internal com-
ponents.
4.Handle your projector carefully. Dropping or jarring your projector could
damage internal components.
5. Do not place heavy objects on top of the projector.
6. If you wish to have the projector installed on the ceiling:
aDo not attempt to install the projector yourself.
bThe projector must be installed by qualified technicians in order to ensure
proper operation and reduce the risk of bodily injury.
cIn addition, the ceiling must be strong enough to support the projector
and the installation must be in accordance with any local building codes.
dPlease consult your dealer for more information.
eDo not attempt to stack projectors on the ceiling.
To Dealer or Installer:
To prevent the projector from falling, install it in a place and fasten it in a
way with sufficient strength to suppor t the combined weight (107 kg/
236 lb) of the projector (84 kg/185.3 lb), the lens (10 kg/22 lb) and the
ceiling mount(13 kg/28.7 lb) for an extended period of time as well as to
withstand earthquakes.
Power Supply
1. The projector is designed to operate on a power supply of 2.8 KW
AC200-240V 50/60Hz. Ensure that your power supply fits this re-
quirement before attempting to use your projector.
2. Handle the power cable carefully and avoid excessive bending. A
damaged cord can cause electric shock or fire.
3. If the projector will not be used for an extended period of time, dis-
connect the plug from the power outlet.
4. Placing the power cord and the RGB cable closely to each other can
cause beat noise. If this happens, keep the two separated so that
beat noise is not generated.
Cleaning
1. Unplug the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled,
use a mild detergent. Never use strong detergents or solvents such
as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to
scratch or mar the lens. 
						

							E – iv
Précautions contre lincendie ou la décharge
1. Sassurer quil y ait une ventilation suffisante et que les ouvertures
ne soient pas obstruées afin déviter des concentrations
potentiellement dangereuses dozone et laccumulation de chaleur à
lintérieur du projecteur. Laisser au moins 20 cm despace entre le
projecteur et un mur. Veuillez laisser un espace libre d’au moins 50
cm (20 pouces) entre les orifices de ventilation et l’objet.
2. Empêcher tous objets étrangers tels que des attaches trombones ou
des morceaux de papier de tomber à lintérieur du projecteur. Ne pas
essayer de récupérer des objets qui seraient tombés dans le
projecteur. Ne pas introduire dobjets métalliques tels quun fil ou un
tournevis dans le projecteur. Si quelque-chose doit tomber dans le
projecteur, le débrancher immédiatement et faire enlever lobjet par
un technicien agréé DIGITAL PROJECTION.
3. Ne pas poser de liquides sur le dessus du projecteur.
ATTENTION: La lampe à haute pression peut exploser si elle est
manipulée incorrectement. Confier lentretien à du personnel
dentretien qualifié.
Précautions avec la lampe : lire avant lutilisation
La lampe a été scellée dans un environnement sous pression, et il y
a donc un petit risque dexplosion, si elle nest pas utilisée
correctement. Le risque est minime si lappareil est en bon ordre de
marche, mais sil est endommagé ou utilisé au-delà des 750 heures
recommandées, le risque dexplosion augmente alors.
Il est à noter lexistence dun système davertissement intégré, lequel
affiche le message Lamp Running Time is Over 750 Hours!! (Le
temps de fonctionnement de la lampe a dépassé 750 heures !!)
lorsque les 750 heures de fonctionnement sont atteintes. Lorsque
ce message apparaît, prière de contacter son revendeur DIGITAL
PROJECTION pour un remplacement.
Si la lampe explose, de la fumée peut être produite par les fentes
daération situées sur le côté de lappareil. Cette fumée est composée
de verre sous forme de particules et de gaz de Xenon, et nest pas
nuisible si elle est maintenue à distance des yeux. Si les yeux sont
exposés à ce gaz, les rincer immédiatement à leau courante et con-
sulter tout de suite un médecin. Ne pas frotter les yeux ! Cela
pourrait provoquer une grave blessure.
AVERTISSEMENT:
Ne pas regarder dans lobjectif lorsque le projecteur est allumé. De
sérieux dommages aux yeux pourraient en résulter.
Recommandations importantes
Ces instructions de sécurité ont pour but dassurer une longue vie à
votre projecteur et déviter un incendie ou une décharge électrique. Prière
de les lire avec attention et de tenir compte de tous les avertissements.
Installation
1. Placer le projecteur sur une surface plate et de niveau, et dans un
endroit sec et à labri des poussières et de lhumidité.
2. Ne pas exposer le projecteur aux rayons directs du soleil, ni le placer
près dun chauffage ou de dispositifs de radiation de chaleur.
3. Lexposition aux rayons directs du soleil, à la fumée ou à la vapeur
pourrait endommager des composants internes.
4. Manipuler le projecteur avec précautions. Laisser tomber le projecteur
ou lui donner des chocs pourrait endommager des composants in-
ternes.
5. Ne pas poser dobjets lourds sur le dessus du projecteur.
6. Si vous voulez installer le projecteur au plafond:
a. N’essayez pas d’installer le projecteur vous-même.
b. Le projecteur doit être installé par un technicien qualifié pour garantir une
installation réussie et réduire le risque d’éventuelles blessures corporelles.
c.De plus le plafond doit être suffisamment solide pour supporter le projecteur
et l’installation doit être conforme aux réglementations locales de con-
struction.
d. Veuillez consulter votre revendeur pour de plus amples informations.
e. Ne pas superposer les projecteurs accrochés au plafond.
A l’attention du revendeur ou de l’installateur:
Afin d’empêcher une chute éventuelle du projecteur, veuillez prendre
en compte lors de son placement et de sa fixation de la force nécessaire
pour suppor ter le poids total (107 kg), celui du projecteur (84 kg), de
l’objectif (10 kg) et de l’ensemble de fixation au plafond (13 kg), pour de
longues périodes et de façon à lui permettre de résister aux
tremblements de terre.
Alimentation
1.Le projecteur est conçu pour fonctionner sous une tension
dalimentation de 2,8 KW CA 200-240 V 50/60 Hz. Sassurer que la
tension du secteur soit conforme à ces caractéristiques avant dutiliser
le projecteur.
2. Manipuler le cordon dalimentation avec précautions et éviter des
flexions excessives. Un cordon endommagé peut occasionner une
décharge électrique ou un incendie.
3. Si le projecteur ne doit pas être utilisé pendant une longue période,
débrancher la fiche de la prise de courant.
4. Placer le cordon dalimentation et le câble RGB tout près lun de
lautre peut occasionner un bruit de battement. Si cela se produit, les
maintenir séparés jusquà ce que le bruit de battement disparaisse.
Nettoyage
1. Débrancher le projecteur avant de le nettoyer.
2. Nettoyer régulièrement le boîtier extérieur avec un chiffon humide.
Sil est très sale, utiliser un détergent doux. Ne jamais utiliser de
détergent forts ou de solvants tels que de lalcool ou du diluant.
3. Utiliser un souffleur ou du papier pour objectif pour nettoyer lobjectif,
et faire attention de ne pas griffer ou endommager lobjectif.
ATTENTION
Ne pas débrancher le câble d’alimentation de la prise du secteur
dans les circonstances suivantes car cela risque d’endommager le
projecteur:
•Lorsque le message “Veuillez patientez un instant“ apparaît. Ce
message sera affiché après que le projecteur soit éteint.
•Immédiatement après que le cordon dalimentation électrique ait
été branché sur la prise du mur (lindicateur POWER nest pas
encore devenu orange).
•Immédiatement après que le ventilateur de refroidissement de
soit arrêté de fonctionner. (Après que le projecteur ait été mis
hors tension à l’aide du bouton POWER OFF, le ventilateur
d’aération continue à tourner durant 3 minutes tandis que le
INDICATOR à deux chiffres -- clignote). 
						

							E – v
Declaration of Conformity
Directives covered by this Declaration
89/336/EEC Electromagnetic Compatibility Directive, amended by 92/31/EEC & 93/68/EEC.
73/23/EEC Low Voltage Equipment Directive, amended by 93/68/EEC.
Products covered by this Directive
Large Screen Projector type THUNDER 10000sx Chassis EURO
THUNDER 10000sx Chassis USA
Basis on which Conformity is being declared
The products identified above comply with the protection requirements of the above EU
directives, and the manufacturer has applied the following standards:-
EN55022:1998 - Limits and Methods of Measurements of Radio Disturbance Characteristics
Information Technology  Equipment.
EN 55024:1998 - Limits and Methods of Immunity Characteristics of Information
Technology Equipment.
EN 61000-3-2:1998 - Harmonic Current Emissions.
EN 61000-3-3:1995 - Immunity to  Voltage Fluctuations and Flicker.
The technical documentation required to demonstrate that the products meet the requirements
of the Low Voltage directive has been compiled by the signatory below and is available for
inspection by the relevant enforcement authorities. The CE mark was first applied in April 2002.
Signed:
Authority: D.J. Quinn, Director - Product Development
Date:17th April 2002
Attention!
The attention of the specifier, purchaser, installer, or user is drawn to special measures and limitations
 to use which must be observed when these products are taken into service to maintain compliance
with the above directives. Details of these special measures are available on request, and are also
contained in the product manuals. 
						

							E – vi
TABLE OF CONTENTS
Video Adj........................................................................E-33
Noise Reduction......................................................E-33
Color Matrix .............................................................E-34
Y/C Delay.................................................................E-34
Telecine...................................................................E-34
Motion Select...........................................................E-34
Motion Level............................................................E-34
YTR Adjustment......................................................E-34
CTR Adjustment......................................................E-34
Option Adj......................................................................E-34
Clamp Timing...........................................................E-34
Sync Protection.......................................................E-34
VD Delay..................................................................E-34
Lens Memory.................................................................E-35
Signal Type.....................................................................E-35
Switcher.........................................................................E-35
Gain.........................................................................E-35
Volume.....................................................................E-35
Ref Adj..................................................................................E-35
Keystone........................................................................E-35
Lamp..............................................................................E-36
Lamp Mode..............................................................E-36
Reference White Balance..............................................E-36
Factory Default.....................................................................E-36
Projector Options.................................................................E-36
Timer..............................................................................E-36
On/Off Timer............................................................E-36
Sleep Timer.............................................................E-37
Menu..............................................................................E-37
Menu Mode/Language/Menu Display Time/
  Display Select/Date Format/Date, Time Preset....E-37
Setup..............................................................................E-38
Page 1:
Orientation/Background/S-Video Mode Select . E-38
Page 2:
Signal Select(RGB1/2) /Sync Termination
(RGB 1/2)..........................................................E-38
Page 3:
Signal Select (Video 1/2, S-Video 1/2 and Switcher)E-38
Page 4:
Auto Adjust (RGB Only)....................................E-38
Power Management/Power Off Confirmation ... E-39
Keystone Save/Doubler/Last Memory/
Seamless/Lens Memory/User Name................E-39
Page 5:
  Communication Speed/Projector ID /
  Default Source Select...........................................E-39
Link Mode......................................................................E-39
Switcher Control............................................................E-39
Help......................................................................................E-40
Contents.........................................................................E-40
Source Information........................................................E-40
Projector Information.....................................................E-40
Test Pattern..........................................................................E-40
Selecting a new signal that is close to one of the listed
signals in horizontal and vertical frequency........................E-41
6. SPECIFICATIONS ............................................. E-42
7. Optional Accessories ...................................... E-44
XT SDI BOARD/SX HDSDI BOARD....................................E-44
REMOTE 3 (XLR) Pin Assignments and Signals................E-44
8. Compatible Input Signal List ........................... E-45
9. List of Menu Items Available in Link Mode ...... E-46
Appendix ............................................................. E-47
Dimensions...........................................................................E-47
Tips on Adjusting Focus for Lens Memory Function...........E-48
INTRODUCTIONIntroduction to the SX10000 Projector..................................E-1
Getting Started.......................................................................E-1
Whats in the Box? .................................................................E-1
1. PART NAMES AND FUNCTIONSProjector................................................................................. E-2
Controls............................................................................ E-3
Terminal Panel.................................................................E-4
Remote Control......................................................................E-6
Remote Control Features................................................E-6
Remote Control Precautions...........................................E-7
Remote Control Battery Installation................................E-7
2. INSTALLATIONSetting up Your Projector.......................................................E-8
Screen Size and Projection Distance....................................E-8
Table of Throw Distance and Image Sizes
   for Optional Lenses.............................................................E-8
Lens Shift Adjustable Range.................................................E-9
Moving the Projector............................................................E-10
Selecting a Location.............................................................E-10
3. SETUPConnecting the Power Cable and Turning on the Projector.....E-11
About Star tup Screen..........................................................E-12
Setting up the Projector.......................................................E-13
Keystone...............................................................................E-14
Setting up for Double Stacking in Link Mode......................E-14
Projector Orientation............................................................E-16
4. CONNECTIONSWhen Used in Standalone Operation..................................E-17
When Used with One Switcher (ISS-6020/ISS-6020G)......E-18
When Used with Two or More Switchers (100 Inputs)........E-19
REMOTE 1 Connector.........................................................E-21
Operating Multiple Projectors with the Remote Control......E-23
Using the RGB DIGITAL Connectors...................................E-24
5. OPERATIONGeneral Controls..................................................................E-25
Using the Menus ..................................................................E-25
Shutter Mechanism..............................................................E-25
Customizing Basic/Custom Menu........................................E-26
A List of Direct Key Combinations.......................................E-27
Menu Tree.............................................................................E-28
Menu Elements....................................................................E-30
Menu Descriptions & Functions...........................................E-31
Source Select.......................................................................E-31
Switcher.........................................................................E-31
Entry List........................................................................E-31
Entry Edit Command...............................................E-31
Adjust (Source)....................................................................E-32
Picture............................................................................E-32
Brightness................................................................E-32
Contrast...................................................................E-32
Saturation................................................................E-32
Color........................................................................E-32
Hue..........................................................................E-32
Sharpness...............................................................E-32
V-Aperture...............................................................E-32
Gamma Correction..................................................E-32
White Balance................................................................E-32
Color Temperature...................................................E-32
Brightness................................................................E-32
Contrast...................................................................E-32
Signal Level.............................................................E-32
Image.............................................................................E-32
Pixel Adjust..............................................................E-32
  Clock/Phase..........................................................E-32
Horizontal/Vertical Position.....................................E-33
Aspect Ratio............................................................E-33
Resolution................................................................E-33
Overscan.................................................................E-33
Video Filter..............................................................E-33
Blanking...................................................................E-33 
						

							E – 1
Getting Started
The fastest way to get started is to take your time and do everything
right the first time. Taking a few minutes now to review the manual may
save you hours later on. At the beginning of each section of the manual
youll find an overview. If the section doesnt apply, you can skip it.
Whats In The Box?
Make sure your box contains everything listed. If any pieces are miss-
ing, contact your dealer. Please save the original box and packing ma-
terials if you ever need to ship the projector.
•THUNDER 10000sx Projector
•Remote Control with Remote Cable (wireless/wired)
•DVI-D Cable
•Ferrite clamp core for DVI-D cable
•RGB signal cable (15-pin D-Sub)
•Power Cable (single phase)
•Two AA Batteries
•User Manual
•CompactFlash Memory Card (8MB) with Adapter
INTRODUCTION
This section introduces you to your new THUNDER 10000sx Projector,
provides a list of materials that comes with your projector and describes
the features and controls.
Introduction to the THUNDER 10000sx Projector
The THUNDER 10000sx is one of the finest, most technically advanced
projectors available today. The THUNDER 10000sx enables you to project
exceptionally bright, precise images up to 500 inches across (measured
diagonally) from your PC or Macintosh computer (desktop or notebook),
VCR, document camera, laser disc player, DVD player and even an HD
VCR or HD laser disc player.
You can use the projector on a tabletop or cart, you can permanently
mount it on a ceiling*, or you can use the projector to project images
from behind the screen. The remote control can be used in a wired or
wireless configuration.
Features youll enjoy :
•A high-performance 2.0 KW Xenon lamp that delivers 9000 ANSI
lumens with a lamp life of 750 hours.
•DIGITAL PROJECTION’s unique DLP
TM based light engine offers true
color reproduction.
•The THUNDER 10000sx can accommodate any picture size from 80
to 500 inches (measured diagonally).
•The THUNDER 10000sx projects images with uniform brightness while
colors remain true to their original source.
•The projector can be double stacked without an external frame, pro-
ducing bright images of 18,000 ANSI lumens. In addition, double stack-
ing offers built-in redundancy.
•An image can be projected from in front or behind a screen, and the
projector can even be installed on the ceiling*.
•Supports RGB digital, HDTV and DVD signals as well as most IBM
VGA, S-VGA, XGA, SXGA, UXGA (scaling), Macintosh or any other
RGB signals within a horizontal frequency range or 15 to 107 kHz
and a vertical frequency range of 24 to 105 Hz. This includes
NTSC3.58, PAL, PAL60, SECAM, NTSC4.43, Y/C and 1080p, 1080i,
720p and 480p HDTV standard video signals.
•Built-in telecine detection enables 3:2 pull-down correction with no
external processing necessary, eliminating jitter and artifacts to allow
for original film source motion quality.
•A newly designed menu system provides for easy setup and opera-
tion of the projector.
•The remote control can be used wired or wireless.
*Installing the projector on the ceiling must be done by authorized
DIGITAL PROJECTION technicians.
Consult your DIGITAL PROJECTION dealer for more information.
Digital Light Processing and DLP are trademarks of Texas Instruments.
Digital Projection Limited,
Greenside Way, Middleton, Manchester M24 1XX, UK.
Registered in England No. 2207264, Registered Office: As Above
Tel: +44 (0) 161 947 3300
Fax:+44 (0) 161 684 7674
E-Mail:[email protected], [email protected]
Web Site:www.digitalprojection.co.uk
Digital Projection Inc.
55 Chastain Road, Suite 115, Kennesaw, GA 30144. USA
Tel: (USA) 770 420 1350
Fax: (USA) 770 420 1360
E-Mail: [email protected]
Web Site: www.digitalprojection.com 
						

							E – 2
1. Part Names and Functions
PC Card Slot
*To turn on the main power to the projector, press the switch to the ON
position (I) and the POWER indicator on the rear panel will turn or-
ange in color.
Press to the OFF position (0) to turn the main power off.
NOTE: When turning off the main power, first return the projector to the standby
condition by pressing the POWER OFF button on the remote control or the POWER
button on the rear panel and then turn off the main POWER switch. These pro-
cedures are necessary to protect your projector and the connected equipment.
Stacking Pad (4 pcs)
Ventilation (out)
Carrying HandleFoot
Input Terminal Panel Remote Sensor
Lens (Optional)
Insert a PC memory card
here to upgrade the
projector system software
or copy data. To access
the slot, loosen the screw.
Connect the supplied power
cable here (AC 200-240V).
AC INPUT
Controls
Carrying Handle Power Switch (Main power)*
Projector 
						

							E – 3
LENS SHIFT
ZOOM MENU SELECT
-+
ENTER
ONINDICATOR POWER
STATUS
ON/OFF
OFF
CANCEL FOCUS
11 10 9 8 7 5 4 2
1 3 6
1. Power Button
Press to turn the projector on when the projector is in the standby con-
dition (Main Power switch must be on and the POWER indicator lit or-
ange). Press and hold for 2 seconds to turn off the projector.
2. Power Indicator
When this indicator is green, the projector is on; when the indicator is
orange, it is in standby mode.
NOTE: After the projector is turned off, the indicator -- flashes for three min-
utes to show that the cooling fan is working.
Do not turn off the main power during that time. After -- stops flashing, the
POWER indicator will change to a steady orange glow and the projector will be
in the stand-by mode.
3. Status Indicator
When the On Timer is set and the projector is in the standby mode, the
Status indicator flashes green to show that the On Timer program is
active.
4. Two Digit Display
During normal operation the current projector ID (address) is shown in
this two digit display. In the event of an error, a projector error code will
be displayed. The display can be turned off using the ON/OFF Switch to
the left of the display.
5. Enter Button
Executes your menu selection and activates items selected from the
menu. When the slidebar or dialog box is displayed:
Pressing this button confirms adjustments/setting and returns to the
previous menu display.6. Cancel Button
Press this button to exit the menu. Press this button to return the adjust-
ments to the last condition while you are in the adjustment or setting
menu.
7. Select (Up/Down/Left/Right) Button
Up/Down: Use these buttons to select the menu of the item you wish to
adjust.
Left/Right: Use these buttons to change the level of a selected menu
item.
8. Menu Button
Displays the main menu for operation.
9. Zoom Button
Zoom the lens in and out.
10. Focus Button
Adjust the lens focus.
11. Lens Shift Button
Adjust the lens offset by shifting the projected image position horizon-
tally and vertically.Remote sensor
Controls 
						

							E – 4
OUTPUT
INPUT3
OPTION
REMOTE1RGB
OUTIN
REMOTE2
REMOTE3INPUT7
INPUT8 INPUT5 INPUT6
OUT
LED
ON
OFF IN
INY
C S-VIDEO1
S-VIDEO2 VIDEO1 VIDEO2 R/Cr
B/CbCb
H/HV
V VH/HV B/CbG/Y G/YR/CrCr
SDI Y
INPUT2 INPUT1 INPUT4
OUTPUT
INPUT0
RGB DIGITALINPUT9
OUT
5
1
2
3
4
1312 11 10 9 8 7 6
Terminal Panel
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Space to install the optional SD-SDI or SX HD-SDI board.