Digital Projection Showlite 5000sx+ Lcd Projector Users Manual

8-27
8. Using On-Screen Menu
Enabling Sleep Timer
1. Select your desired time between 30 minutes and 16 hours: Off, 0:30,
1:00, 2:00, 4:00, 8:00, 12:00, 16:00.
2. Select “Set” and press the ENTER button on the remote control.
3. The remaining time starts counting down.
4. The projector will turn off after the countdown is complete.
NOTE:
•To cancel the preset time, set Off for the preset time or turn off the power.
•When the remaining time reaches 3 minutes before the projector is turned off,
the...

8-28
8. Using On-Screen Menu
Type
Standard lamp
Extended life lampNormal
2000HEco
3000HModel
001-715
001-716 4500HLamp life (H) Page 2
Signal Type, Video Type, Sync Type, Interlace, Direct Key
Projector Information
Displays the information for your projector such as lamp usage,
filter usage, version number and others. This dialog box has three
pages.
Page 1
Remaining Lamp 1 Time, Remaining Lamp 2 Time, Lamp 1 Hour
Meter, Lamp 2 Hour Meter
NOTE: The progress indicator shows the percentage of remaining...

9
Maintenance
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
z Replacing the Lamp .................................................. 9-2
x Replacing or Cleaning the Filter ............................... 9-3
c Cleaning the Cabinet and the Lens .......................... 9-4 

9-2
This chapter describes the simple maintenance procedures you
should follow to replace the lamp and the filter, and to clean the
filter and the cabinet.
z Replacing the Lamp
The projector has two lamps. The lamp replacement procedure
applies to both lamps. After your lamp 1 and 2 has been operat-
ing for 2000 hours (Normal mode on the standard life lamp) or
longer, the Lamp indicator in the cabinet will blink red and the
message will appear. Even though the lamp may still be working,
replace it as...

9-3
x Replacing or Cleaning the Filter
To replace the filter:
•Replace both filters at the same time.
•Before replacing the filters, remove dust and dirt from the pro-
jector cabinet.
•The projector contains high-precision parts. Keep out dust and
dirt during filter replacement.
•Do not wash the filter with water. Water will damage the filter
membrane.
•Reattach the filter cover correctly. Failure to do so may cause
projector malfunction.
Preparation: Replace the lamp before replacing the filters.
1....

9-4
1. Turn off the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong detergents or solvents such as alcohol
or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.
c Cleaning the Cabinet and the Lens
3
D
 R
E
F
O
R
M3D
A
SELECT
LENS SHIFTFOCUS
ZOOMDOWN LEFT
RIGHT UPZSTATUSPC CARD 2
PC CARD 1LAMP 1
LAMP 2
POWER
ON/STAND BYAUTO ADJUSTMENUENTERCANCEL
F
USB...

10
Appendix
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
z USB Memory Device or USB Memory Card Reader Support ....10-2
x Troubleshooting ...................................................... 10-3
c Specifications ......................................................... 10-5
v Cabinet Dimensions ............................................... 10-7
b Pin Assignments of D-Sub RGB Input Connector .. 10-7
n Compatible Input Signal List ................................... 10-8
m REMOTE 1 Connector...

10-2
10. Appendix
z USB Memory Device or USB Memory Card
Reader Support
The projector is compatible with either a USB memory device or
USB memory card reader which supports the viewer and secu-
rity features.
•To use a USB memory device or USB memory card reader,
connect the device to the USB port (type A).
•Select one of the Drive icons in the Viewer toolbar, Capture
toolbar and PC Card File setting screen. Up to four drives can
be accepted.
•To use a USB memory device as a Protect key for Security...

10-3
x Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Power Indicator
Indicator Condition
Projector Condition Note
Off
Blinking light
Steady lightGreen blinking
Orange blinking0.5 sec ON,
0.5 sec OFF
2.5 sec ON,
0.5 sec OFF
0.5 sec ON,
0.5 sec OFF
2.5 sec ON,
0.5 sec OFFThe main power is off
The projector is getting ready to turn on.
Off Timer or Sleep Timer is active.
The projector is cooling down.
On Timer is active.
The projector is...

10-4
Does not turn on
No picture
Image isn’t square to the
screen
Picture is blurred
Image is scrolling verti-
cally, horizontally or
both
Remote control does
not work
Indicator is lit or blink-
ing
Cross color in RGB
mode
USB mouse does not
work
No on-screen menu•Check that the power cable is plugged in and that the main power switch on the projector is on. See pages 1-
9 and 2-11.
•Ensure that the lens hood or the lamp cover is installed correctly. See pages 1-4 and 9-2.
•Check to see if the projector...