Digital Projection Projector WQXGA User Manual

www.digitalprojection.com
english
21
1 Basic setup
1.1  Lens
1.1.1  Lens and lens mount
A range of fixed and zoom lenses is available to cover most applicatio\
ns, both front and rear. 
The lenses are powered and fitted with a bayonet mount for ease of installation.
IMPORTANT! Switch off all equipment before setting-up for proper function. 
When mounting and changing lenses, be aware that the optical system is exposed to dust 
and foreign particles as long as the lens is not attached to the system. Do...

english
22
WQXGA User’s Guide – 
Basic setup
1.2 Adjusting on screen image size and position
Adjusting the placement of the image on screen can be done using the:
1.  Adjustable feet (E in Figure 5-1).
2.  Lens shift mechanism controlled from the keypad, the remote control, RS-232 or LAN (A 
in Figure 9).
3.  Zoom (for lenses with zoom) in the lens controlled from the keypad, the remote control, 
RS-232 or LAN (B in Figure 5-1).
After the correct image size and position is found, please adjust the image...

www.digitalprojection.com
english
23
1.3 Lamp operation
The projector is fitted with two individual projection lamps that can be run in various modes. 
In addition, lamps can be replaced as needed separately. This ensures an optimized cost of 
ownership. Individual lamp timers are maintained for each lamp.
Lamp operation mode is controlled in the INSTALLATION > LAMPS sub menu.
1.4 Ceiling mount
The projector can be ceiling mounted using an approved UL tested/ listed ceiling mount 
fixture, with a...

english
24
WQXGA User’s Guide –  Basic setup
1.4.1 
Ceiling mount cover
The supplied auxiliary cable cover can be mounted on the projector to conceal the interface 
cables and power cord when the unit is ceiling mounted. Connect all cables and fix them in\
 
place before the cable cover is attached to the projector. Figure 5-3 shows the ceiling mount 
cover.
Figure 1-3. The ceiling mount cover
1.4.2 Attaching the ceiling cover
To attach the ceiling mount cover, please follow this procedure:
A  Attach the...

www.digitalprojection.com
english
25
1.5 Connecting and cables
NOTE! Before setting up, switch off all equipment and disconnect the power co\
rd.
1.5.1   Setting up a video source
For best quality video, connect a digital video source using the HDMI 1.3a interface (A) in Fig-
ure 5-4. Both HDMI inputs are HDCP copy protection compliant. Depending on cable quality, 
the projector is supporting the use cables with lengths up 20 meters (65 feet\
). 
Figure 1-4.  Connecting a video source
1.5.2   Setting up...

english
26
WQXGA User’s Guide – 
Basic setup
1.6 Image alignment
For easier alignment of the projector, test images are built into the system.
To enable test images, go to the menu entry INSTALLATION > TEST IMAGE. Cycle the vari-
ous test images using the arrow keys. When a test image matching the aspect ratio of your 
screen has been found, use the zoom, focus, lens shift and physical projector alignment to 
match the screen.
1.7 Setting image orientation
In relation to the screen, the projector...

www.digitalprojection.com
english
27
1.11 Changing the language of the menu system
The projector menu system has a total of 11 user-selectable languages embedded for easier 
use all over the world. The default language is English.
The available languages are:
•	 English
•	 French
•	 German
•	 Spanish
•	 Russian
•	 Norwegian
•	 Swedish
•	 Korean
•	 Japanese
•	 Chinese	Simplified
•	 Chinese	Traditional
•	 Portuguese
•	 Italian
The change the language of the menu system, just select “LANGUAGE”\
 from the...

english
28
WQXGA User’s Guide – 
Basic setupThis page intentionally left blank.   

www.digitalprojection.com
english
29This page intentionally left blank.   

english
30
WQXGA User’s Guide – 
Advanced setup
1 Advanced setup
1.1  Controlling multiple projectors with remote control ID (RCID)
The remote control can be operated either in ‘broadcast mode’, or ‘individual mode’. When 
several projectors are in use in an installation, individual control may be convenient. Individual 
control is available either by wired remote control, using the data-jack, or by using an individ-
ual number code. For individual control, first set the individual RC ID code using the...