Digital Projection Projector M-Vision Cine 3D Series User Manual

							
Digital Projection M-Vision Cine 3D series  2. A TOUR OF THE MENUS  Operating Guide
Page 9Rev A  August 2011
Advanced Menu
Color Space
Set.this.to.Auto,.except.when.the.projector.has.problems.selecting.between.YPbPr,.YCbCr.and.RGB.
Gamma, Color Temperature and Color Gamut
Set.this.to.suit.the.specification.of.the.input.source,.or.to.improve.the.appearance.of.the.projected.image.
Brilliant Color® and Adaptive Contrast
Set.these.to.suit.your.brightness.and.contrast.requirements.
Fine Sync
Adjust.these.settings.to.suit.the.configuration.of.the.input.signal.
RGB Adjust
Adjust.the.RGB.offset.and.gain.settings.to.improve.the.colour.balance.of.the.projected.image.
•
•
•
•
•
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 Brilliant Color® allows for 
increased projector brightness 
and improved color saturation by 
enabling the yellow segments on the 
colour wheel.
 Adaptive Contrast expands 
the light and dark portions of 
the contrast curve of the image, 
depending on the mean luminance 
of the image.
  Setting either of these two 
parameters to On will affect any 
image quality settings made in other 
menus.
Advanced MenuFine Sync
 Fine Sync and RGB Adjust affect 
only RGB input sources. 
						

							
Digital Projection M-Vision Cine 3D series  2. A TOUR OF THE MENUS  Operating Guide
Page 10Rev A  August 2011
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
System Menu
Language
This.product.is.available.only.in.English.at.present.
Menu Position
Set.this.to.determine.the.position.of.the.menus.on.the.screen.
Blank Screen
Set.this.to.determine.what.appears.on.screen.when.the.projector.is.searching.for.a.valid.input.source.
Auto Power Off
Set.this.to.On,.if.you.want.the.projector.to.go.into.Standby mode.when.no.input.source.is.detected.for.20.minutes.
Auto Power On
Set.this.to.On,.if.you.want.the.projector.to.start.up.imediately.when.the.mains.is.connected.
Set.this.to.Off,.if.you.want.the.projector.to.go.into.Standby mode.when.the.mains.is.connected..In.this.case,.the.projector.will.not.start.up.
until.the.POWER.button.is.pressed.on.the.control.panel.or.the.remote.control.
•
•
•
•
•
• 
						

							
Digital Projection M-Vision Cine 3D series  2. A TOUR OF THE MENUS  Operating Guide
Page 11Rev A  August 2011
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
System Menucontinued
Rear Projection
Set.this.to.On.to.reverse.the.image.from.left.to.right,.for.use.in.Rear.Projection.Mode.
Ceiling Mode
Set.this.to.On.to.reverse.the.image.from.top.to.bottom,.for.use.in.Ceiling.Mode.
Lamp Power
Set.this.to.Economy.to.run.the.lamp.at.reduced.power.
•
•
• 
						

							
Digital Projection M-Vision Cine 3D series  2. A TOUR OF THE MENUS  Operating Guide
Page 12Rev A  August 2011
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
 The Trigger outputs can be 
used to automatically control the 
screen or screen shuttering. See 
the Connection Guide for more 
information.
 To set what a ‘blank’ screen looks 
like, use the Blank Screen setting 
in the System menu.
Control Menu
Keys 1 to 5
The..to...keys.on.the.remote.control.can.each.be.programmed.to.switch.to.one.of.the.input.sources.
Trigger 1 and 2
Choose.from.Screen,.Aspect Ratio.or.RS232,.to.determine.what.will.cause.each.Trigger output.to.activate.
Auto-Source
When.this.is.set.to.On,.the.projector.will.search.for.an.alternative.input.source.when.the.current.input.source.is.disconnected
When.this.is.set.to.Off,.the.projector.will.show.a.‘blank’ .screen.when.the.current.input.source.is.disconnected.
•
•
•
• 
						

							
Digital Projection M-Vision Cine 3D series  2. A TOUR OF THE MENUS  Operating Guide
Page 1Rev A  August 2011
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Ser vice MenuInformation
Ser vice MenuFactor y Reset
 Do NOT do this unless you are 
sure that you want to restore ALL 
the current settings to their factory 
defaults.
Ser vice Menu
Information
Press.ENTER/SELECT.to.view.information.about.the.projector,.eg:
Factor y Reset
Press.ENTER/SELECT.to.restore.all.settings.to.their.factory.defaults.
When.the.warning.message.appears,.use..or.to.select.YES.or.NO,.then.press.ENTER/SELECT.to.confirm.your.selection.
•
•
• 
						

							
Digital Projection M-Vision Cine 3D series  2. A TOUR OF THE MENUS  Operating Guide
Page 1Rev A  August 2011
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Ser vice Menucontinued
Blue Only
Set.this.to.On.to.display.only.the.blue.component.of.the.input.signal,.for.calibration.or.test.purposes.
Test Patterns
Use..or.to.select.from.a.range.of.test.patterns.
Press.MENU.to.return.to.the.menu,.or..ENTER/SELECT.to.return.to.the.currently.selected.input.signal.
Altitude
When.this. is.set. to.Auto,.the. internal.fan. will.operate.at.Low.speed,.and.rise.to.High.speed.automatically.if. the.internal.temperature.rises.
When.this.is.set.to.High,.the.fan.will.operate.at.High.speed.continuously,.for.use.at.high.altitude.locations.
•
•
•
•
• 
						

							
Digital Projection M-Vision Cine 3D series  3. MENU MAP  Operating Guide
Page 1Rev A  August 2011
Menu Map
Menu Sub Menus and Controls
MAIN
Aspect Ratio  1:9, Theaterscope, :, : Narrow, Native
Presets
Recall..A, B, C, D, Default
Save..A, B, C, D
Brightness
Contrast
Saturation
Hue
Sharpness
Noise Reduction
Overscan  Off, Crop, Zoom
Input Select  all available inputs
Resync  Projector will re-synchronise with the current input signal
3D Settings
3D.Enable..Off, On
3D.Type..SBS Dual, L-R Dual
DLP .Link..Off, On
L-R.Swap..Normal, Swap
ADVANCED
Color Space   Auto, YPbPr, YCbCr, RGB PC, RGB Video
Gamma  Film, Video, Punch, Graphics, CRT
Color Temperature  00K, 00K, 00K, 900K, Native
Color Gamut  Auto, REC09, SMPTE-C, EBU, Native
BrilliantColor  On, Off
Adaptive Contrast  On, Off
Fine Sync  V Position, H Position, Phase, Tracking, Sync Level
RGB Adjust  RGB Offset and Gain
Notes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
shaded green on the actual menu.
 Where it would be helpful, some 
menu options are described in more 
detail earlier in this operating guide. 
						

							
Digital Projection M-Vision Cine 3D series  3. MENU MAP  Operating Guide
Page 1Rev A  August 2011
SYSTEM
Language  English only
Menu Position  Top Left, Top Right, Bottom Left, Bottom Right, Centre
Blank Screen  Logo, Black, Blue, White
Auto Power Off   On, Off
Auto Power On   On, Off
Rear Projection   Off, On
Ceiling Mode   Off, On
Lamp Power   Standard, Economy
CONTROL
1 Key   all available inputs
2 Key   all available inputs
3 Key   all available inputs
4 Key   all available inputs
5 Key   all available inputs
Trigger 1   Screen, 1:9, Theaterscope, :, : Narrow, RS22
Trigger 2   Screen, 1:9, Theaterscope, :, : Narrow, RS22
Auto Source   On, Off
SERVICE
Information   Model Name, Serial Number, Software Version, Active Source, Signal Format, Pixel Clock, 
H⁄V Refresh Rate, Lamp Hours
Factory Reset  Projector will ask for confirmation before restoring all settings to fac\
tory defaults
Blue Only   Off, On
Test Patterns   Off, White, Black, Red, Green, Blue, Cyan, Magenta, Yellow, Chequer Grid
Altitude   Auto, High
Menu Sub Menus and ControlsNotes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
shaded green on the actual menu.
 Where it would be helpful, some 
menu options are described in more 
detail earlier in this operating guide.