Digital Projection Projector HIGHlite 740 Series User Manual

							page 32
Operating Guide
USING THE MENUS
Editing fields
Some features require a text or numeric field to be edited.
1. To edit a field, first select it using the LEFT and RIGHT arrow buttons, then press OK.
2. Use the LEFT and RIGHT arrow buttons to move the green highlight to the digit or character whi\
ch is to be changed, then use 
UP and DOWN to adjust it.
3. Use the LEFT and RIGHT arrow buttons to select the next digit or character.
4. Press OK to accept the new value, or press EXIT to exit without changing.
.
Notes
 Some menu items may not be 
available due to settings in other 
menus. These will be grayed out on 
the actual menu.
The highlighted digit is being edited
   
Digital Projection HIGHlite 740 Series 
Rev I Februar y 2015  
						

							page 33
Operating Guide
USING THE PROJECTOR
Using The Projector
Main menu
• Input Selection 
Select an input source from the drop-down list.
• Test Pattern 
Set Input Selection to Test pattern and then select a test pattern from the drop-down list.
• Lens, Image, Color and Geometry 
Open these sub-menus to access various picture and screen settings.
• Edge Blend / PIP 
PIP and Edge Blend are mutually exclusive modes of operation. When the projector is in Edg\
e 
Blend mode (as shown in the picture), PIP is not available, and vice versa. 
• Lamps 
Select lamp configuration and adjust lamp power.
• Setup 
Adjust Input Configuration, Network, On Screen Display and System settings.
• Information 
View your current configuration
Notes
Main Menu
 You can also select an input source 
by pressing the following buttons on 
the remote control: 
1 for VGA  
2 for HDMI 1 
3 for DVI 1 
4 for 3G-SDI 
5 for CVBS 1 
6 for S-Video  
7 for Component  
8 for CVBS 2
  Test patterns are subject to image 
controls, so brightness, contrast 
etc. will affect their appearance on 
screen.
 Do not use the provided test 
patterns for ColorMax.
 You can upload custom test patterns 
using a network connection - see 
Virtual OSD in the Protocol Guide.
 See also Using The Menus earlier 
in this guide and  Appendix D: 
Menu Map in the Reference Guide.
   
Digital Projection HIGHlite 740 Series 
Rev I Februar y 2015  
						

							page 34
Operating Guide
USING THE PROJECTOR
Lens menu
Zoom
To move the lens in or out:
1. Select Zoom In or Zoom Out, then press OK.
2. When the image is the desired size, select Zoom Stop and then press OK.
Focus
To adjust the focus:
1. Select Focus Near or Focus Far, then press OK.
2. When the image is correctly focused, select Focus Stop and then press OK.
Center Lens
To center the lens, select Center Lens and press OK.
Nudge
To position the image correctly on the screen, use the Nudge controls.
Notes
Main MenuLens
 You can also move the lens, focus 
and zoom using the keypad or the 
remote:
• Press SHIFT followed by an 
arrow button to shift the lens up, 
down, left and right.
• Press FOCUS followed by the 
UP and DOWN arrow buttons to 
adjust the focus.
• Press ZOOM followed by the 
UP and DOWN arrow buttons to 
zoom in and out.
Main Menu Lens Nudge
   
Digital Projection HIGHlite 740 Series 
Rev I Februar y 2015  
						

							page 35
Operating Guide
USING THE PROJECTOR
Image menu
• Brightness, Contrast, Gamma, Hue and Saturation
Set the slider or select from the drop-down list as required, to improve\
 the quality of the image.
• Black Level Offset
Set this to 0 IRE or 7.5 IRE as required.
• Use V Position and H Position to adjust the position manually.
Video Filters
Set the sliders or select from the drop-down list as required, to improv\
e the quality of the image:
• Sharpness - a peaking filter to increase high frequency/luminance information.
• Detail - a filter which removes low frequency image components.
• Luma Sharpness - a filter which enhances luminance sharpness.
• Chroma Sharpness - a filter which enhances the color sharpness of the chrominance signal by 
increasing the steepness of color edges.
• Recursive NR - a noise reduction filter which reduces spatial & temporal noise (only applicable to 
standard definition video signals).
• Mosquito NR - a noise reduction filter which reduces block artifacts (only applicable to standard 
definition video signals).
• Cross Color Suppression - a filter which reduces luminance  to chrominance crosstalk on 
Composite Video signals. The crosstalk appears as a rainbow pattern in regions of fine detail.
VGA Setup
Use Auto Setup to allow the projector to detect the appropriate settings automatically\
.
If you require manual adjustment:
• Set the Phase slider to correct for shimmering or poor quality definition on, for example, fine text.
• Set the Total H Samples slider to match the resolution of the incoming video signal.
Notes
Main MenuImage
 You can also press BRI, CON or 
GAMMA on the remote control.
 Hue applies only to NTSC signals.
 When a new input mode is detected 
(e.g. NTSC, HDTV 1080p, SVGA 
etc.), all the 
Input Settings are 
saved so that they can be recalled 
next time that input mode is 
displayed.
Main Menu Image Video Filters
Main Menu Image VGA Setup
 VGA Setup is not available unless 
a VGA signal is present.
   
Digital Projection HIGHlite 740 Series 
Rev I Februar y 2015  
						

							page 36
Operating Guide
USING THE PROJECTOR
Color menu
Gamut
Peak gives you the brightest possible image.
Choose HDTV for high definition standards and SDTV for standard definition standards.
A value between 3200K and 9000K selects the relevant color temperature.
You can upload your own gamut using the Projector Manager software, and t\
hen select it from 
the User 1 and User 2 settings.
Black Level and Gain sliders
Set the sliders as required.
Notes
Main MenuColor
   
Digital Projection HIGHlite 740 Series 
Rev I Februar y 2015  
						

							page 37
Operating Guide
USING THE PROJECTOR
Geometr y menu
Aspect Ratio
Choose between Source, Fill Display, Fill & Crop, Anamorphic and TheaterScope.
Some devices (e.g. certain DVD players) pack a 16:9 image into a 4:3 a\
spect ratio. In such cases to 
display the image correctly, choose the Anamorphic aspect ratio.
Overscan
Set this slider to compensate for noisy or badly defined image edges.
Image with noisy edgesOverscanned image
Notes
Main Menu
Geometr y
An anamorphic lens (optional accessory) is used with the 
TheaterScope setting, to ensure 
that for a 2.35:1 image, the 
maximum area of the DMD is used, 
giving maximum image brightness.
For examples of how the different aspect ratios affect screen 
dimensions, see  Aspect Ratios 
Explained in the Reference Guide.
  Items on this page may be 
unavailable depending on the 
Geometr y Engine setting.
   
Digital Projection HIGHlite 740 Series 
Rev I Februar y 2015  
						

							page 38
Operating Guide
USING THE PROJECTOR
Size & Position
• Set Enable to On or Off.
• Use Setting to choose:
Global, in which case these settings will be applied to all signals on all inp\
uts.
or Per Mode, in which case these settings will be applied only to the current input\
 signal.
• Set the H Position and V Position sliders as required.
• Set H Size and V Size. When Aspect Lock is set to On, the V Size slider is disabled.
• Select Reset and press OK to reset all the sliders.
Notes
Main MenuGeometr y Size & Position
   
Digital Projection HIGHlite 740 Series 
Rev I Februar y 2015  
						

							page 39
Operating Guide
USING THE PROJECTOR
Geometr y Engine
Choose from Keystone, Cornerstone, Rotation, War p or Off.
• If Geometr y Engine is set to Keystone, set the H Keystone and V Keystone sliders to correct 
for any distortion caused by the projector being in a different horizontal or vertical plane to the 
screen.
1 The projector is positioned at an angle
2 The resulting image is distorted
3 The image is corrected when Keystone is applied
Notes
Main Menu
Geometr y
 Some items on this menu may 
be unavailable depending on the 
Geometr y Engine setting.
 If possible, position the projector 
facing the screen at a right angle to 
avoid geometry corrections.
123
   
Digital Projection HIGHlite 740 Series 
Rev I Februar y 2015  
						

							page 40
Operating Guide
USING THE PROJECTOR
Geometr y Engine (continued)
Keystone settings
1 Projector to the left
The projector is positioned 
to the left of the screen.
To correct, apply a positive 
H Keystone value using 
the RIGHT arrow button.
2 Projector to the right
The projector is positioned 
to the right of the screen.
To correct, apply a negative 
H Keystone value using 
the LEFT arrow button.
3 Projector high
The projector is positioned 
above the screen at a 
downward angle.
To correct, apply a negative 
V Keystone value using 
the LEFT arrow button.
4 Projector low
The projector is positioned 
below the screen at an 
upward angle.
To correct, apply a positive 
V Keystone value using 
the RIGHT arrow button.
5 Projector straight
The projector is directly 
opposite the screen at a 
right angle both horizontally 
and vertically.
No correction is needed.
Notes
Main Menu
Geometr y
 If possible, position the projector 
facing the screen at a right angle to 
avoid geometry corrections.
Horizontal and vertical keystone corrections
1
4
2
53
   
Digital Projection HIGHlite 740 Series 
Rev I Februar y 2015  
						

							page 41
Operating Guide
USING THE PROJECTOR
Geometr y Engine (continued)
• Pincushion / Barrel is enabled if Geometr y Engine is set to Keystone or Rotation.
Set the slider to correct for any distortion caused by the screen being \
concave or convex.
Notes
Main MenuGeometr y
 Some items on this menu may 
be unavailable depending on the 
Geometr y Engine setting.
 If possible, position the projector 
facing the screen at a right angle to 
avoid geometry corrections.
PincushionBarrel
   
Digital Projection HIGHlite 740 Series 
Rev I Februar y 2015