Digital Projection Projector E-Vision 8000 Series User Manual

							Digital Projection E-Vision 8000 Series  INTRODUCTION Remote Communications Guide
55
Introduction
The projector can be controlled by using an external control system or a\
 PC via a LAN or RS232 serial interface, using a terminal-emulation 
program, such as HyperTerminal.
Operation commands
Operation commands simulate menu operations and determine the settings o\
f the projector, and use the following format:
• All commands consist of ASCII text strings starting with the letters ‘op’, and ending with\
 an ASCII Carriage Return character:
op   [CR]
• The  string can take one of the following formats:
Description
Set= Makes the setting take that value.
Get?Asks what the current value is.
The value is returned as an ASCII text string.
Increment+Adds 1 to the current value.
Decrement–Subtracts 1 from the current value.
Execute(none)Performs an action.
Examples
op input.sel = 1 [CR] sets the input signal to DVI
op input.sel ? [CR] asks what is the input signal
op brightness + [CR] increments the brightness setting
op contrast – [CR] decrements the contrast setting
op auto.img [CR]   commands the projector to attempt to re-synchronise to the current input\
 source
Key commands
Key commands duplicate remote control key presses and use the following \
format:
ky [CR]
Examples
ky testpattern[CR] brings up the list of available test patterns (identical to pressing th\
e TEST PATTERN key on the remote)
ky input[CR]   brings up the list of available input sources (identical to pressing th\
e INPUT key on the remote)
ky power.off[CR]   switches the projector off (identical to pressing the POWER OFF key on the remote)
Notes
 Details of how to connect to the 
projector, using the serial control 
or LAN inputs, can be found in the 
Connections Guide.
 Spaces in the commands are 
necessary.
  eg  op input.sel = 1 
NOT opinput.sel=1
 The TCP Port number is 7000.
 The Serial Port settings are:
 ●Baud rate - 38,400 bps
 ●Data length - 8 bits
 ●Stop bits - one
 ●Parity - none
 ●Flow control - none 
Rev F July 2014  
						

							Digital Projection E-Vision 8000 Series  THE OPERATION COMMANDS Remote Communications Guide
56
The Operation Commands
Notes
INPUT menu
input.sel= ?0 = HDMI
1 = DVI
2 = VGA
3 = Component / BNC
4 = Composite
5 = S-Video
6 = 3G-SDI
Not applicable when Picture Mute is On.
pip= ?0 = Off
1 = On
pip.sel= ?1 = HDMI
2 = DVI
3 = VGA
4 = Component / BNC
5 = Composite
6 = S-Video
7 = 3G-SDI
Cannot be set to 0.
pip.swap(execute)Swap main and PIP sourceNot applicable without signal locked.
pip.pos= ?0 = Top left
1 = Top right
2 = Bottom left
3 = Bottom right
4 = Split L-R
Not applicable when PIP is Off.
continued on next page...
Notes 
Rev F July 2014  
						

							Digital Projection E-Vision 8000 Series  THE OPERATION COMMANDS Remote Communications Guide
57
...continued from previous page
Notes
pattern= ?0 = Color Bar
1 = Cross Hatch
2 = Burst
3 = Red
4 = Green
5 = Blue
6 = White
7 = Black
8 = Cross Mark
9 = Cross Hatch + Mark
10 = Red (TI)
11 = Green (TI)
12 = Blue (TI)
13 = HRamp (TI)
14 = Off
color.space= ?0  = Auto
1 = YCbCr
2 = YPbPr
3 = RGB-PC (0-255)
4 = RGB-Video (16-235)
Not applicable without signal locked.
input.lock= ?0  = Auto
1 = 48 Hz
2 = 50 Hz
3 = 60 Hz
Not applicable without signal locked.
no.signal= ?0 = Logo
1 = Blue
2 = Black
3 = White
vid.std= ?0  = Auto
1 = PAL
2 = SECAM
3 = NTSC
Not applicable without signal locked.
Only valid when the input is Composite or 
S-Video.
auto.imgadj= ?0 = Off
1  = Auto
2  = Always
Not applicable without signal locked.
continued on next page...
Notes 
Rev F July 2014  
						

							Digital Projection E-Vision 8000 Series  THE OPERATION COMMANDS Remote Communications Guide
58
...continued from previous page
Notes
PICTURE menu
pic.mode= ?0 = High Bright
1 = Presentation
2 = Video
contrast= ? + -0 ~ 200Not applicable without signal locked.
dyna.cont= ?0 = Off
1 = On
Not applicable without signal locked.
bright= ? + -0 ~ 200Not applicable without signal locked.
saturat= ? + -0 ~ 200Not applicable without signal locked.
Only valid when the input is Composite or 
S-Video.
tint= ? + -0 ~ 200Hue
Not applicable without signal locked.
Only valid when the input is Composite or 
S-Video.
gamma= ?0 = Film
1 = Graphics
2 = Video
3 = Linear
Not applicable without signal locked.
color.temp
(pic.mode is 
“High Bright”)
?5 = NativeNot applicable without signal locked.
Not applicable when Color Space is set to 
Custom.
Not applicable when edge blending is on.
color.temp
(pic.mode is 
“Presentation”)
= ?2 = 6500K
5 = Native
Not applicable without signal locked.
Not applicable when Color Space is set to 
Custom.
Not applicable when edge blending is on.
color.temp
(pic.mode is 
“Video”)
= ?0 = 5000K
2 = 6500K
3 = 7800K
4 = 9300K
5 = Native
Not applicable without signal locked.
Not applicable when Color Space is set to 
Custom.
Not applicable when edge blending is on.
red.offset= ? + -0 ~ 200Not applicable without signal locked.
green.offset= ? + -0 ~ 200Not applicable without signal locked.
continued on next page...
Notes 
Rev F July 2014  
						

							Digital Projection E-Vision 8000 Series  THE OPERATION COMMANDS Remote Communications Guide
59
...continued from previous page
Notes
blue.offset= ? + -0 ~ 200Not applicable without signal locked.
red.gain= ? + -0 ~ 200Not applicable without signal locked.
green.gain= ? + -0 ~ 200Not applicable without signal locked.
blue.gain= ? + -0 ~ 200Not applicable without signal locked.
sharpness= ? + -0 ~ 200Not applicable without signal locked.
nr= ? + -0 ~ 200Noise Reduction
Not applicable without signal locked.
aspect= ?0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = Letterbox
7 = Native
8 = Unscaled
Not applicable without signal locked.
Native aspect ratio is not applicable when zoom is 
set to Zoom.
zoom= ?0 = Off 
1 = Crop 
2 = Zoom
Overscan
Not applicable without signal locked.
Zoom is not applicable when aspect ratio is set to 
Native.
h.total= ? + -0 ~ 200Not applicable without signal locked.
Only applicable when the source is either VGA or 
Component.
h.pos= ? + -0 ~ 200Not applicable without signal locked.
h.phase= ? + -0 ~ 200Not applicable without signal locked.
Only applicable when the source is either VGA or 
Component.
v.pos= ? + -0 ~ 200Not applicable without signal locked.
auto.img(execute)Auto Sync
Not applicable without signal locked.
continued on next page...
Notes 
Rev F July 2014  
						

							Digital Projection E-Vision 8000 Series  THE OPERATION COMMANDS Remote Communications Guide
60
...continued from previous page
Notes
LAMPS menu
lamps= ?0 = Single
1 = Dual
Not applicable when lamp is cooling.
lamp.mode= ?0 = Economy
1 = Standard
2 = Dimming
Drive
Not applicable without signal locked.
lamp.pwr= ?0 ~ 25 ( 80.4 % ~ 100.0 % )Not applicable without signal locked.
altitude= ?0 = Off
1 = On
High Altitude
lamp1.stat?0 = Off
1 = On
lamp2.stat?0 = Off
1 = On
ALIGNMENT menu
proj.mode= ?0 = Front
1 = Rear
2 = Ceiling + Front
3 = Ceiling + Rear
fan.pos= ?0 = Normal
1 = Vertical
2 = Down
zoomio+ -+ = Zoom out
- = Zoom in
focus+ -+ = Focus Near
- = Focus Far
vert.offset+ -+ = Up
- = Down
Vertical Lens Shift
horiz.offset+ -+ = Right
- = Left
Horizontal Lens Shift
lens.load=1 ~ 10Lens Memory Load
lens.save=1 ~ 10Lens Memory Save
lens.center(execute)
continued on next page...
Notes 
Rev F July 2014  
						

							Digital Projection E-Vision 8000 Series  THE OPERATION COMMANDS Remote Communications Guide
61
...continued from previous page
Notes
h.keystone= ? + --350 ~ +350The sum of the absolute values of h.keystone and 
v.keystone cannot be greater than 350.
v.keystone= ? + --200 ~ +200The sum of the absolute values of h.keystone and 
v.keystone cannot be greater than 350.
warp.rotat= ? + --20 ~ +20Each unit is ¼°. 
warp.pinbrl= ? + --100 ~ +100Pincushion/Barrel
warp.tlc.x
warp.tlc.y
= ? + -x: -192 ~ +192
y: -120 ~ +120
Top Left Corner
warp.trc.x
warp.trc.y
= ? + -x: -192 ~ +192
y: -120 ~ +120
Top Right Corner
warp.blc.x
warp.blc.y
= ? + -x: -192 ~ +192
y: -120 ~ +120
Bottom Left Corner
warp.brc.x
warp.brc.y
= ? + -x: -192 ~ +192
y: -120 ~ +120
Bottom Right Corner
warp.reset(execute)
blank.top= ? + -0 ~ 360
blank.btm= ? + -0 ~ 360
blank.left= ? + -0 ~ 534
blank.right= ? + -0 ~ 534
blank.rst(execute)
eb.stat= ?0 = Off
1 = On
Edge Blend
eb.wht.top= ? + -0, 200 ~ 500Blend Width Top
1-199 not allowed
eb.wht.btm= ? + -0, 200 ~ 500Blend Width Bottom
1-199 not allowed
eb.wht.left= ? + -0, 200 ~ 800Blend Width Left
1-199 not allowed
eb.wht.right= ? + -0, 200 ~ 800Blend Width Right
1-199 not allowed
eb.blk.top= ? + -0, 8, 16, 24, 32Black Level Uplift Area Top
continued on next page...
Notes 
Rev F July 2014  
						

							Digital Projection E-Vision 8000 Series  THE OPERATION COMMANDS Remote Communications Guide
62
...continued from previous page
Notes
eb.blk.btm= ? + -0, 8, 16, 24, 32Black Level Uplift Area Bottom
eb.blk.left= ? + -0, 4, 8, 12, 16, 20, 24, 28, 32Black Level Uplift Area Left
eb.blk.right= ? + -0, 4, 8, 12, 16, 20, 24, 28, 32Black Level Uplift Area Right
eb.all= ? + -0 ~ 32Black Level Uplift Adjust Width All
eb.red= ? + -0 ~ 32Black Level Uplift Adjust Width Red
eb.green= ? + -0 ~ 32Black Level Uplift Adjust Width Green
eb.blue= ? + -0 ~ 32Black Level Uplift Adjust Width Blue
eb.reset(execute)
eb.adl= ?0 = Off
1 = On
Align Pattern
CONTROL menu
eco.net.pow= ?0 = Off (ECO Standby Mode)
1 = On (Standard Standby Mode)
Eco Network Power
auto.powoff= ?0 = Off 
1 = On
auto.powon= ?0 = Off 
1 = On
proj.ctrl= ?0 = RS232
1 = network
Not applicable when Eco Network Power is on.
net.ipaddr= ?
net.subnet= ?
net.gateway= ?
net.dhcp= ?0 = Off
1 = On
startup.logo= ?0 = Off
1 = On
continued on next page...
Notes 
Rev F July 2014  
						

							Digital Projection E-Vision 8000 Series  THE OPERATION COMMANDS Remote Communications Guide
63
...continued from previous page
Notes
trig.1= ?0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = Letterbox
7 = Native
8 = Unscaled
9  = Auto
If trig.1 is set to Auto, the projector will start 
sending the trigger as soon as it is switched on. 
Otherwise the trigger will be sent only when the 
aspect ratio matches this setting.
auto.src= ?0 = Off 
1 = On
Auto Search
dblack= ?0 = Off
1 = On
Dynamic Black
lang= ?0 = English
1 = French
2 = Spanish
3 = German
4 = Portuguese
5 = Chinese Simplified
6 = Chinese Traditional
7 = Japanese
8 = Korean
SERVICE menu
model?
ser.no?
sw.ver?
act.src?0 = HDMI
1 = DVI
2 = VGA
3 = Component / BNC
4 = Composite
5 = S-Video
6 = 3G-SDI
Active Source
continued on next page...
Notes 
Rev F July 2014  
						

							Digital Projection E-Vision 8000 Series  THE OPERATION COMMANDS Remote Communications Guide
64
...continued from previous page
Notes
pip.src?0 = HDMI
1 = DVI
2 = VGA
3 = Component / BNC
4 = Composite
5 = S-Video
6 = 3G-SDI
PIP Source
pixel.clock?In MHz
Not applicable without signal locked.
signal?Not applicable without signal locked.
h.refresh?Not applicable without signal locked.
v.refresh?Not applicable without signal locked.
lamp1.hours?
lamp2.hours?
proj.runtime?
blue.only= ?0 = Off
1 = On
fact.reset(execute)Factory reset
Miscellaneous commands
power.on(execute)Power on
power.off(execute)Power off (puts projector into Standby mode)
picture.mute= ?0 = Off
1 = On
status?0 = standby 
1 = warm up 
2 = imaging 
3 = cooling 
4 = warning
remote.set= ?1 ~ 10: Set Projector ID
255: Clear Projector ID (No ID)
Notes 
Rev F July 2014