Digital Projection Mercury Hd Users Manual

8-25 Digital Projection   
MERCURY HD8. Using the On-Screen Menus
To delete PC card data you registered.
1. Use the SELECT  button to select Delete and use the SELECT button to select the list window.
2. Use the SELECT 
 button to select the PC card data you wish to
delete.
3. Press the SELECT 
 button to select Delete and press the ENTER
button.
The PC card data will be deleted.
If youve lost your registered PC card, proceed as follows:
NOTE: Digital Projection or your dealer will provide you with your...

8-26 8. Using the On-Screen Menus Digital Projection   
MERCURY HD
3. Select “Edit” and press the ENTER button to open the Edit window.
4. Set the Day, Time (24 hours format), On-Time and Off-Time using the
SELECT buttons and the Software keyboard (1 thru 10).
5. Select On Timer or Off Timer
6. Repeat the Timer
To repeat the On Timer or Off Timer program every week, place a
check mark in “Repeat”.
7. Select “OK” and press the ENTER button on the remote control to
complete the setting. To cancel this and...

8-27 Digital Projection   
MERCURY HD8. Using the On-Screen Menus
Enabling Sleep Timer
1. Select your desired time between 30 minutes and 16 hours: Off, 0:30,
1:00, 2:00, 4:00, 8:00, 12:00, 16:00.
2. Select “Set” and press the ENTER button on the remote control.
3. The remaining time starts counting down.
4. The projector will turn off after the countdown is complete.
NOTE:
• To cancel the preset time, set Off for the preset time or turn off the
power.
• When the remaining time reaches 3 minutes before...

8-28 8. Using the On-Screen Menus Digital Projection   
MERCURY HD
Source Information Page 2
Signal Type, Video Type, Sync Type, Interlace, Direct Key
Projector Information
Displays the information for your projector such as lamp
usage, filter usage, version number and others. This dialog
box has three pages.
Projector Information Page 1
Lamp 1 Hour Meter, Lamp 2 Hour Meter
NOTE: The meters show the sum of Eco and Normal hours. A warning
message will appear on screen near the expected end of life. This...

9
Routine Maintenance
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
1 Replacing the Lamp ................................. 9-2
2 Replacing or Cleaning the Filter .............. 9-3
3 Cleaning the Cabinet and the Lens ......... 9-3 

9-2 9. Routine Maintenance Digital Projection   
MERCURY HD
1 Replacing the Lamp
The projector has a single lamp pre-wired into the lamp
module. After the lamp has been operating for 1000 hours
(Normal mode using the standard lamp, part number 102-246),
the Lamp indicator on the control panel will blink red and a
warning message will appear. Even though the lamp may still
be working, replace it as soon as possible to maintain optimal
projector performance.
CAUTION
• DO NOT TOUCH THE LAMP immediately...

9-3 Digital Projection   
MERCURY HD9. Routine Maintenance
2 Replacing or Cleaning the Filter
The air-filter prevents dust or dirt from getting inside the
projector and should be cleaned after every 100 hours of
operation (more often in dusty conditions). If the filter is dirty
or clogged, your projector may overheat.
NOTE: The message Please clean the filters will be displayed each
time the projector is turned on after it has been used in excess of 168
hours. Should this message appear, clean the...

9-4 9. Routine Maintenance Digital Projection   
MERCURY HD 

10
Appendix
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
1 USB Memory Device or USB Memory
Card Reader Support .............................10-2
2 Troubleshooting .....................................10-3
3 Specifications ........................................10-5
4 Cabinet Dimensions ...............................10-7
5 Pin Assignments of D-Sub RGB Input
Connector...............................................10-7
6 Compatible Input Signal List .................10-8
7 REMOTE 1 Connector...

10-2 10. Appendix Digital Projection   
MERCURY HD
1 USB Memor y Device or USB Memor y Card
Reader Support
The projector is compatible with either a USB memory device or
USB memory card reader which supports the viewer and secu-
rity features.
• To use a USB memory device or USB memory card reader,
connect the device to the USB port (type A).
• Select one of the Drive icons in the Viewer toolbar, Capture
toolbar and PC Card File setting screen. Up to four drives can
be accepted.
• To use a USB memory...