Digital Projection Lightning 38 Wuxga 3d User Manual

english
11
4 Installation and setup
The following section outlines the general requirements to supporting equipment in order 
to run the FusionNet Calibrator and successfully setting up a multi imag\
e based projection 
system.
4.1 System requirements
FusionNet 2.0 – required to set up and operate multi image processing system processors, 
works with Microsoft Windows® operating systems only. The following versions are sup-
ported:
•	Windows XP (32-bit only), SP xx or 
•	Windows Vista (32- or 64-bit)
•...

english
12FUSION - Installation and setup
4.2 System overview
The FUSION processing system contains the following main components:
•	An Image Generator (IG) with one or more channels (outputs) (not provided by  Digital Projection).
•	One multi image unit per channel
•	One projector per channel
•	A PC for setup and control
•	Optional CAD tool for designing systems (not provided by Digital Projection)
Figure 4-1 shows a complete system overview of a multi image processing setup.
Figure 4-1.  FUSION...

english
13
4.4 LED indicators / Front button
The front button and the Power and Status LED-indicators on the processor front panel have 
the following functions:
Front button:Power LED:Status LED:
Push 1 time:Show info on screen(visual ID/IP/present serial no.)BLUE: ONGREEN: ON
Push 3 times:RebootBLUE: Blinking •	Booting	upGREEN: Blinking •	DVI	IN	not	valid	and/or•	Network	not	OK
Press and hold 5 seconds:Network resetYELLOW: Blinking•	Upgrading	 softwareRED: ON •	Temperature	too	high
Press and hold 15...

english
14FUSION - Installation and setup
4.6 Firewall settings
The multi image processing system processor communicates extensively on the network. In 
order for it to communicate freely with the FusionNet application, the following ports must be 
open in the firewall:
•	22 outbound (SSH) 
•	1900 inbound (UPnP open for AutoDiscovery of multi image processing system  processors)
•	30000 outbound (dedicated multi image processing instruction command set)
•	40400 outbound (dedicated ASCII command set)
•...

english
15
5 Getting to know the GUI
5.1 FusionNet.site
Figure 5-1 gives an overview of FusionNet.site. The application has four main\
 areas of 
interest:
•	The File menu located in the top-left corner.
•	The “Site Devices” overview on the left hand side of the GUI.
•	Control, status, monitoring and timed operations overviews for one or more selected devices on the right hand side.
•	Status messaging window at the bottom.
Figure 5-1.  Overview of FusionNet.site
To start the multi image processing system...

english
16FUSION - Getting to know the GUI
5.2 FUSION Calibrator – Device View
Figure 5-2 shows the “Device View” window that is displayed when the “FUSION Calibrator” 
plugin is started. The “Device View” window contains the following areas:
•	The File menu located in the top-left corner
•	The Device Pool window in the lower left corner.
•	A FUSION processing system information window in the lower right corner.
•	A dedicated toolbar on the left hand side.
•	A Device View Desktop that is displayed in the...

english
17
Figure 5-3.  File menu, Device View.
5.2.3 Adding multi image processing system units to a project
To enable and add multi image processing system units to a project, simply drag and drop 
units from the tree view in the Device Pool (Figure 5-4) to the Device View Desktop. The multi 
image processing system units in the Device Pool are detected using FusionNet’s built-in 
universal plug-n-play capability.
Figure 5-4.  The Device Tree in the Device Pool.
Multi image processing system units can...

english
18FUSION - Getting to know the GUI
5.2.4 Using the Device View Toolbar, DVT
The Device View Desktop window has a toolbar on the left hand side, known as the Dev\
ice 
View Toolbar. The toolbar can be shown with or without help texts, see Figure 5-5.  
Figure 5-5.  Toolbars, shown with and without help texts.
Using the toolbar you can:
•	Add or remove multi image processing system units from a project.
•	Select or deselect all multi image processing system units on the Desktop.
•	Show an...

english
19
5.2.5 Clearing calibration
To clear calibration from selected multi image processing system units, select Edit > Clear 
Calibration from the File menu. Under Clear Calibration, one can select to clear all o\
r just 
parts of the calibration. See Figure 5-6.
Figure 5-6.  Clearing calibration
5.2.6 Notifications and advanced network settings
Under Settings > Application Settings, message notification levels and\
 advanced network 
settings are configured, see Figure 5-7.
 
Figure 5-7....

english
20FUSION - Getting to know the GUI
The software update process is complete when the power status LED on the unit is showing 
a steady blue light.
Figure 5-8.  FUSION software upgrade window.
5.2.8 Controlling EDID information
The unit defaults to giving the image generator either WUXGA or WQXGA ED\
ID data 
depending on the version of the multi image processing system unit that is in use. EDID 
data can also be configured manually, or the unit can pass EDID data information from the 
projector...