Digital Projection Lightning 38 Wuxga 3d User Manual

							an introduction to the processors,  
use and set up
user’s guide
FUSION     
						

							english
2FUSION User’s Guide – Introduction
This page intentionally left blank.   
						

							english
3
1 Introduction
1.1 Thank you
Thank you for purchasing a Multi image processing system processor.
The Multi image processing systems FUSION are state-of-the-art image processing engines 
for the combination and setup of multiple projectors in order to create one, large, seamless 
image. By combining multiple projectors, images with unprecedented resolution and fidelity 
can be created.
The multi image processing system processors feature unique functionality and unmatched 
compatibility, and are perfectly tailored to working with Digital Projection projectors for use in 
multi-image environments.
1.1 Features
•	Geometry correction
•	Blending and overlap
•	 2560x1600 and 1920x1200 resolution models available
•	User selectable algorithm setups
•	4x4 Lanczos scaling
•	Bi-linear scaling
•	B-cubic scaling
•	Project onto any surface
•	Zero, or near zero latency, depending on set up and configuration
•	3D stereo compatible, up to 1920x1200 on FUSION 3D, and 1280x800 on FUSION MD
•	Patented Black Level Matching for uniform black levels
•	Per-pixel Colour-, Uniformity-, and brightness matching
•	12-bit internal resolution
•	Dual-Link DVI-D in / out
•	All control through Ethernet
•	Built-in power supply for easy power management in large racks
•	Integrates seamlessly with the FusionNet multi image processing system  
software setup suite
•	Rack mount, ½ width, 1U height
•	Unlimited scalability and channel count
•	Fully transparent to source, no special software or source requirements   
						

							english
4FUSION User’s Guide – Introduction
Contents of this User’s Guide
1 Introduction 3
1.1 Thank you
1.1 Features
2 SAFETY  7
2.1 GENERAL WARNINGS
2.1 WEEE INFORMATION
2.1 WARNING ABOUT SUBSTANCES
2.1.1  WARNING SYMBOLS
3 What’s in the box?  9
4 Installation and setup  11
4.1 System requirements
4.2 System overview
4.3 Connectors
4.4 LED indicators / Front button
4.5 Network settings
4.6 Firewall settings
4.7 Software
4.8 Mounting the FUSION processor in rack
5  Getting to know the GUI  15
5.1 FusionNet.site
5.2 FUSION Calibrator – Device View
5.2.1  Creating and saving a FUSION system setup project
5.2.2 Backing up and restoring calibration
5.2.3 Adding multi image processing system units to a project
5.2.4 Using the Device View Toolbar, DVT
5.2.5 Clearing calibration
5.2.6 Notifications and advanced network settings
5.2.7 Performing software upgrades
5.2.8 Controlling EDID information
5.3 FUSION calibrator – Calibration View
5.3.1  Using the Calibration View Toolbar (CVT)
5.3.2 Selecting/deselecting FUSION processing units
5.3.3 Using the Calibration Panel Toolbar (CPT)
5.4 FUSION processing operational states
5.4.1  Bypass states   
						

							english
5
5.4.2 Calibration state
5.4.3 Online state
5.4.4 Auto state
6 Geometry correction  27
6.1 Warping algorithms
6.1.1 Perspective
6.1.2  Mesh Warp Transform
6.1.3 Mesh Warp Bezier
6.2 Warping user interface
6.3 Scaling filters
6.3.1  Lanczos filter
6.3.2 B-spline filter
6.3.3 C-spline filter
6.3.4 Linear interpolation filter
6.4 Working with the perspective algorithm
6.5 Working with the Mesh Transform algorithm
6.6 Working with Mesh Bezier algorithm
6.7 Fine tuning control points 
6.8 Real Time Warp 
7  Edge blending  35
7.1 Introduction
7.2 Edge blending algorithms
7.2.1  Basic edge blending
7.2.2 Advanced edge blending
7.2.3 User interface for basic edge blending
7.2.4 User interface for advanced edge blending
7.2.5 Adjusting the shape of advanced edge blending zones
7.2.6 Adjusting the advanced blend drop-off curve
8 Black Level Management  41
8.1 Creating adjustment zones
8.2 Removing BLM zones
8.3 Adjusting black level in a defined zone
9 Masking  45
9.1 Adding areas to clip
9.2 Removing clip areas   
						

							english
6FUSION User’s Guide – Introduction
10 Storing and recalling data  49
10.1 Storing/recalling calibration to/from the FUSION unit
10.2 Storing/recalling data to/from the control PC
10.3 Accept  calibration
11  Technical specifications  53
11.1 Electrical
11.2 Mechanical   
						

							english
7
2 SAFETY
This device complies with safety regulations for Information Technology Equipment intended 
to operate in “normal” environments (offices and homes). Before using the device for the first 
time, please read the safety instructions thoroughly.
2.1 GENERAL WARNINGS
Use only the cables and cords supplied with the device or original replacement cables. Using 
other cables or cords may lead to malfunction and permanent damage of the device.
Always use 3-prong / grounded power cord to ensure proper grounding of the device. Never 
use 2-prong power cords, as this is dangerous and could lead to electrical shock.
Never open the device. The device contains no user serviceable parts. Re\
fer all repairs to 
qualified personnel only. Make sure that no objects enter into the vents and openings of the 
set.
Do not spill any liquids on the device or into the vents or openings of \
the device.
Always remove protective plastic covering the device before operating the device.
Only place the device on a stable surface, or mount it securely in a rack. 
Do not drop the device.
The device can be used as desktop or rack mounted with the certificati\
on labels facing 
down. Any other mounting directions are not allowed. When rack mounted, care must 
be taken to keep ventilation on back and front sides open. Operating the device in other 
positions may lead to overheating, resulting in malfunctioning.
Always allow ample airflow through the device. Never block any of the air vents. Never 
cover the device in any way while running. Allow for sufficient distan\
ce to walls and other 
obstructions to avoid overheating.
Minimum safety distance to front or rear of the device is 20 cm (8”) to rear and 5 cm (2”) to 
front.
The device is designed for indoor use only. Never operate the device outdoors.
Do not operate the device outside its temperature and humidity specifications, as this may 
result in overheating and malfunctioning.
Only connect the device to signal sources and voltages as described in the technical 
specification. Connecting to unspecified signal sources or voltages may lead to malfunction 
and permanent damage of the device.
2.1 WEEE INFORMATION
This product conforms to all requirements of the EU Directive on waste electrical and 
electronic equipment (WEEE). This product should be recycled properly. It can be 
disassembled to facilitate proper recycling of the individual parts. 
Consult your dealer or relevant public authority regarding drop-off points for collection of 
WEEE.    
						

							english
8FUSION - Safety instructions
2.1 WARNING ABOUT SUBSTANCES
This product contains chemicals, including lead, known to the State of California to cause 
birth defects or other reproductive harm. Recycle properly, do not dispose of in ordinary 
waste!. 
 
2.1.1 WARNING SYMBOLS
 READ USER GUIDE Attention! Read the user guide for further information!
 RECYCLE Warning! Recycle properly, do not dispose of in ordinary waste! 
 NO TELEPHONE Warning! Do not connect to telephone lines!   
						

							english
9
3 What’s in the box?
The FUSION MDP (1920 x 1200) and MDP 3D (2560 x 1600) comes with the\
 following: 
Multi image processing system unit
Power Cable (Country Dependant)
2x Dual Link DVI cables
CD with software
Network cable
User Documentation
Please verify that you have all compoents upon unpacking the unit, and i\
ts contents.
Please save packaging materials for future use, should it be necessary to ship the unit.    
						

							english
10FUSION – What’s in the box?