Digital Projection Lightning 30sx+m, 40sx+m User Manual

page 4.19        105-681B January 2007
Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual 4. Using the menus
Notes
Do not make changes to the
networking configuration
unless you understand what
you are doing, or have taken
advice from your Network
Manager.
If you make a mistake, it is
possible that you will lose
contact with the projector.
Always double-check your
settings before pressing the
APPLY button.
Always keep a written note of
the original settings, and any
changes you have made.
The...

page 4.20        105-681B January 2007
4. Using the menus Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual
Notes
Do not make changes to the
networking configuration
unless you understand what
you are doing, or have taken
advice from your Network
Manager.
If you make a mistake, it is
possible that you will lose
contact with the projector.
Always double-check your
settings before pressing the
APPLY button.
Always keep a written note of
the original settings, and any
changes you have made.
When...

page 4.21        105-681B January 2007
Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual 4. Using the menus
Notes
The buttons of the Main menu
are always visible at the bottom
of the display.
To go back to a previous menu
option that is no longer visible,
call up the menu again using
the appropriate Main menu
button.
Touchscreen calibration should
not normally be necessary
except after many hours of
heavy use.
Config menu
Menu buttons...
Networking config
Detailed status
Touchscreen calibration...

page 4.22        105-681B January 2007
4. Using the menus Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual
Notes
Software update should NOT
be carried out except by, or
with the supervision of,
Digital Projection Service
personnel.
Engineering & Maintenance
menu
Controls
Log files
Menu buttons...
Software update
Engineering & Maintenance menu
Press the ENGINEERING & MAINTENANCE button on the Main menu:
Log files
A single log file is created for each day that the projector is switched on. There...

page 5.1       105-681B January 2007
5. Maintenance
Contents
5. Maintenance5.1
Changing the lamp .................................................................................................................. 5.2
Lamp-hours meter........................................................................................................................................... 5.3
Changing the filter...

page 5.2       105-681B January 2007
5. Maintenance Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual
Changing the lamp
The lamp should be changed after 750 hours of use, as indicated on the lamp-hours
meter. The meter is located on the front of the lamp module, and is accesible inside
the lamp compartment door.
To open the lamp compartment door:
• Give the catch half a turn anti-clockwise, to release the catch.
Notes
Always allow the lamp to cool
for 5 minutes before
removing the lamp module....

page 5.3       105-681B January 2007
Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual 5. Maintenance
Mercury meter
LCD meter
display button
The LCD Lamp-hours meter has two modes of operation:
• When the lamp is switched on, the LCD will show lamp run hours.
• When the lamp is switched off, the LCD will be blank.
Press the button and hold for 5 seconds to display lamp run hours.
Lamp-hours meter
There are two types of Lamp-hours meter, depending on the lamp module that has
been fitted, as shown...

page 5.4       105-681B January 2007
5. Maintenance Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual
To change the lamp:
• Press the LAMP button on the Main menu.
• Press LAMP OFF and hold for 3 seconds. The lamp will ramp down to minimum
and go off after a further 3 seconds.
• Allow the lamp to cool for 5 minutes.
• Push the main power switch downwards to switch off the power.
• Open the lamp compartment door.
• Unscrew each of the three lamp module screws until the thread disengages and
the knob...

page 5.5       105-681B January 2007
Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual 5. Maintenance
Changing the filter
To change the filter:
• Press the LAMP button on the Main menu.
• Press LAMP OFF and hold for 3 seconds. The lamp will ramp down to minimum
and go off after a further 3 seconds.
• Allow the lamp to cool for 5 minutes.
• Push the main power switch downwards to switch off the power.
• Pull the filter out from under the front of the projector, under the lens, by pulling
on the...

page 5.6       105-681B January 2007
5. Maintenance Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual
Notes
Never use strong detergents
or solvents such as alcohol
or thinners to clean the
projector and lens.
Cleaning the projector and lens
Turn the projector off before cleaning.
Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild
detergent.
Use a blower or lens paper to clean the lens, taking care not to scratch the glass.