Digital Projection Lightning 30sx+m, 40sx+m User Manual

page 3.5       105-681B January 2007
Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual 3. Getting started
Notes
For more detailed information
about all the touch screen
menus, see the next section:
Using the menus. • Press the IMAGE button on the Main menu.
• Press the CONTRAST, BRIGHTNESS or GAMMA buttons.
• Touch and drag the red sliders up and down, or for fine adjustment, press the
arrow heads. 

page 3.6       105-681B January 2007
3. Getting started Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual
Switching the power off
• Press the LAMP button on the Main menu.
• Press LAMP OFF. Hold the button pressed until the button turns to yellow, then
release.  The lamp power will ramp down to minimum then go off after a further 3
seconds.
• Allow the lamp to cool for 5 minutes.
• Push the main power switch downwards to switch off the power.
• When the power is switched off, all current settings...

page 4.1        105-681B January 2007
4. Using the Menus
Contents
4. Using the Menus4.1
Introduction............................................................................................................................. 4.2
Menu structure................................................................................................................................................ 4.3
Show mode...

page 4.2        105-681B January 2007
4. Using the menus Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual
Introduction
All of the projector ’s features can be controlled using:
• the menus on the touch screen or
• the same menus on a remote computer using a web browser
(with the IP address of the projector typed into the browser address field)
None of the menus are ever displayed on the projection screen.
In these instructions, it is assumed that the touch screen is being used, so the
expressions...

page 4.3        105-681B January 2007
Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual 4. Using the menus
Menu structure
Show mode (p4)
Show mode indicators
Lamp status
Warnings
Input source
LCD screen blank
IP addresses
Menu buttons....
Main menu
Lamp menu (p6)
Controls
Lamp power slider
Menu buttons...
Shutter open
Shutter close
Lamp on
Lamp off
Maximum power
Minimum power
Lamp/lens memories
Lens menu (p8)
Controls
Move
Zoom
Focus
Menu buttons...
Shutter open
Shutter close
Centre
Calibration...

page 4.4        105-681B January 2007
4. Using the menus Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual
Show mode
When the projector is first switched on, the control panel will be in Show mode, as
shown below:
In Show mode, these icons are displayed:
Lamp status
Lamp off Lamp off Lamp on Lamp on
Shutter closed Shutter open Shutter closed Shutter open
Input source
Single/Dual/Twin mode
Notes
The buttons of the Main menu
are always visible at the bottom
of the display, as shown here.
To go back...

page 4.5        105-681B January 2007
Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual 4. Using the menus
Warnings
If a projector fault is detected, the warning symbol will be displayed, with an
explanatory message.
LCD screen blank
To blank the LCD screen, press and hold the Digital projection logo at the top of the
screen for about two seconds. On release, the screen will blank.
To restore the display, press anywhere on the screen.
IP addresses
The IP addresses of the two ethernet ports are...

page 4.6        105-681B January 2007
4. Using the menus Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual
Notes
The buttons of the Main menu
are always visible at the bottom
of the display.
To go back to a previous menu
option that is no longer visible,
call up the menu again using
the appropriate Main menu
button.
Lamp menu
Press the LAMP button on the Main menu:
Lamp power
To adjust the lamp power, touch and drag the red slider up and down, or for fine
adjustment, press the arrow heads. The...

page 4.7        105-681B January 2007
Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual 4. Using the menus
Notes
The Lamp/Lens memories are
useful if you need to swap
repeatedly and easily between
the settings for a number of
different lenses, or venues.
Stored zoom settings will be
accurate only if the lens is
calibrated. (see next page)
Lamp/Lens memories
Press the LAMP/LENS MEMORIES button.
Store
To store the current Lamp power, Shutter status, Lens shift, zoom and focus
settings for future...

page 4.8        105-681B January 2007
4. Using the menus Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual
Lens menu
Press the LENS button on the Main menu:
Move, zoom and focus
To adjust the move, zoom and focus settings, press the MOVE, ZOOM and FOCUS
arrow heads.
Lens movements will start slowly, then speed up as the button is held. To make fine
adjustments therefore, use a number of short presses.
Shutter open/closed
Press the SHUTTER OPEN or SHUTTER CLOSE button.
Centre
To centre the lens,...