Digital Projection Lightning 30sx+m, 40sx+m User Manual
Have a look at the manual Digital Projection Lightning 30sx+m, 40sx+m User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 577 Digital Projection manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
page 4.19 105-681B January 2007 Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual 4. Using the menus Notes Do not make changes to the networking configuration unless you understand what you are doing, or have taken advice from your Network Manager. If you make a mistake, it is possible that you will lose contact with the projector. Always double-check your settings before pressing the APPLY button. Always keep a written note of the original settings, and any changes you have made. The buttons of the Main menu are always visible at the bottom of the display. To go back to a previous menu option that is no longer visible, call up the menu again using the appropriate Main menu button. Config menu... Network configuration... Wireless LAN Settings... IP address Netmask Encryption Menu buttons... Configure ethernet #1 Configure encryption Wireless LAN Basic networking configuration • Follow the configuration instructions exactly as described on the previous page for Ethernet #1 . Configuration menu, continued
page 4.20 105-681B January 2007 4. Using the menus Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual Notes Do not make changes to the networking configuration unless you understand what you are doing, or have taken advice from your Network Manager. If you make a mistake, it is possible that you will lose contact with the projector. Always double-check your settings before pressing the APPLY button. Always keep a written note of the original settings, and any changes you have made. When entering the channel number, a leading zeroes must be used for single digit numbers: eg 02 If the WEP security key is to be used, then the projector must be set to the same method and number of bits as the computer or wireless access point. Config menu... Network configuration... Wireless LAN... Encryption Settings... SSID Channel WEP key Mode Menu buttons... Configure ethernet #1 Configure wirelss LAN Encryption • Press the ENCRYPTION button. • To change the SSID, press the SSID field. Use keypad to enter the (up to) 12 digits SSID. This will appear in the field at the top of the keypad. Press ENTERto transfer the SSID from the keypad display to the SSID field. • To change the channel number, press the CHANNEL field. Use keypad to enter the channel number (01 - 16, including a leading zero for single figure numbers). This will appear in the field at the top of the keypad. Press ENTERto transfer the number from the keypad display to the Channel field. • To change the WEP Key, press WEP Key a number of times to cycle through the options. Choose from: Disabled 64 bits(0x1234567890) (10 hex digits) 128 bits(0x12345678901234567890123456) (26 hex digits) Pass Phrase(abcdefghijklmnopqrstuvwx) (24 characters) Press the WEP Key field. Use keypad to enter the key. This will appear in the field at the top of the keypad. Press ENTERto transfer the key from the keypad display to the WEP Key field. • To change the mode, press the MODE button to choose from: Infrastructure Access Point(usual mode for an established corporate network) Adhoc peer to peer(usual mode for a single computer and projector)
page 4.21 105-681B January 2007 Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual 4. Using the menus Notes The buttons of the Main menu are always visible at the bottom of the display. To go back to a previous menu option that is no longer visible, call up the menu again using the appropriate Main menu button. Touchscreen calibration should not normally be necessary except after many hours of heavy use. Config menu Menu buttons... Networking config Detailed status Touchscreen calibration Reset IP addresses Configuration menu, continued Detailed status Press the DETAILED STATUS button. The Software release version and the total number of hours of operation are shown. Touchscreen calibration If you suspect that the LCD touchscreen has drifted out of calibration, press and hold the TOUCHSCREEN CALIBRATION button on the Config menu: A target appears in one corner of the screen. Press on the centre of the target and repeat as the target moves around the screen. After touching all four corners, you can wait a few seconds and carry out the calibration again, or exit by pressing the button in the centre of the screen. Reset IP addresses To reset these to their factory settings, press and hold the RESET IP ADDRESSES button. The button will turn grey - hold it until it turns yellow, then release.
page 4.22 105-681B January 2007 4. Using the menus Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual Notes Software update should NOT be carried out except by, or with the supervision of, Digital Projection Service personnel. Engineering & Maintenance menu Controls Log files Menu buttons... Software update Engineering & Maintenance menu Press the ENGINEERING & MAINTENANCE button on the Main menu: Log files A single log file is created for each day that the projector is switched on. There will only be one file per day, regardless of how many times the projector has been switched on and off. The log files cannot be accessed from the projector touch screen. However, in the event of a problem with the projector, the log files can be downloaded to a remote computer via a network connection, and emailed to Digital Projection for analysis. To open a log file on a remote computer: • Click on the log file name. Software update (only available via a browser, not when operating directly from the projector touch screen) This should NOT be carried out except by, or with the supervision of, Digital Projection Service personnel.
page 5.1 105-681B January 2007 5. Maintenance Contents 5. Maintenance5.1 Changing the lamp .................................................................................................................. 5.2 Lamp-hours meter........................................................................................................................................... 5.3 Changing the filter ................................................................................................................... 5.5 Cleaning the projector and lens ............................................................................................. 5.6
page 5.2 105-681B January 2007 5. Maintenance Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual Changing the lamp The lamp should be changed after 750 hours of use, as indicated on the lamp-hours meter. The meter is located on the front of the lamp module, and is accesible inside the lamp compartment door. To open the lamp compartment door: • Give the catch half a turn anti-clockwise, to release the catch. Notes Always allow the lamp to cool for 5 minutes before removing the lamp module. There are no user-serviceable parts inside the lamp module. The whole module should be replaced and returned to Digital Projection for re- furbishment. Do not use the lamp for more than 750 hours, as this may cause serious lamp failure, damage the lamp module and cause extra cost on replacement. Xenon lamps produce high intensity light. Do not look directly at the light coming from the lamp housing or the lens. Door catch Lamp module
page 5.3 105-681B January 2007 Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual 5. Maintenance Mercury meter LCD meter display button The LCD Lamp-hours meter has two modes of operation: • When the lamp is switched on, the LCD will show lamp run hours. • When the lamp is switched off, the LCD will be blank. Press the button and hold for 5 seconds to display lamp run hours. Lamp-hours meter There are two types of Lamp-hours meter, depending on the lamp module that has been fitted, as shown below. Notes
page 5.4 105-681B January 2007 5. Maintenance Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual To change the lamp: • Press the LAMP button on the Main menu. • Press LAMP OFF and hold for 3 seconds. The lamp will ramp down to minimum and go off after a further 3 seconds. • Allow the lamp to cool for 5 minutes. • Push the main power switch downwards to switch off the power. • Open the lamp compartment door. • Unscrew each of the three lamp module screws until the thread disengages and the knob can be pulled out a little against its spring pressure. • Pull the lamp module out of the projector. To fit the new lamp module: • Rest the lamp module on the edge of the compartment and line up the white nylon guides. • Gently but firmly, push the lamp module in all the way until the connector engages. • Screw in each of the three lamp module screws until finger tight. • Push the lamp compartment door closed.Notes Take care when removing the lamp module, as it is heavy (>10kg). Take care not to touch the glass surface of the lamp module. If you do accidentally touch the glass, it should be cleaned before use. Lamp module screws
page 5.5 105-681B January 2007 Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual 5. Maintenance Changing the filter To change the filter: • Press the LAMP button on the Main menu. • Press LAMP OFF and hold for 3 seconds. The lamp will ramp down to minimum and go off after a further 3 seconds. • Allow the lamp to cool for 5 minutes. • Push the main power switch downwards to switch off the power. • Pull the filter out from under the front of the projector, under the lens, by pulling on the strap. • Replenish the filter material. • Push the replenished filter firmly back into the slot, taking care to fit it the right way up, as shown by the arrow. Notes The filter should be changed regularly: • In a clean environment such as an office, change after 750 hours, at the same time as the lamp is changed. • In a dusty or smoky environment such as a theatre or public area, more frequent changes may be necessary.
page 5.6 105-681B January 2007 5. Maintenance Digital Projection LIGHTNING 30sx+m, 40sx+m User Manual Notes Never use strong detergents or solvents such as alcohol or thinners to clean the projector and lens. Cleaning the projector and lens Turn the projector off before cleaning. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Use a blower or lens paper to clean the lens, taking care not to scratch the glass.