Digital Projection Highlite 16000Dsx+, Highlite 10000dsx+ Users Manual

							E-51
Store ............ Enables you to store the currently projected sig-
nal.
NOTE: This can be done by pressing CTL and ENTRY LIST buttons.
Cut ............... Enables you to remove a selected signal from
the list and place it on the clipboard in the Pro-
jector.
Copy ............ Enables you to copy a selected signal from the
list and place it on the clipboard in the Projec-
tor.
Paste ........... Enables you to paste the signal placed on the
clipboard to any other line of the list. To do this,
select Paste and then select the line number
you want to paste to. Last press ENTER.
Edit .............. Enables you to change source names or assign
the direct key.
Source Name
Enter a signal name. Up to 18 alphanumeric char-
acters can be used.
Input Terminal
Change the input terminal.
Direct key
You can assign specific remote keys for direct
signal input selection.
Lock
Set so that the selected signal cannot be deleted
when All Delete is executed. The changes can-
not be saved.
Skip
Set so that the selected signal will be skipped
during auto search.
When complete, select OK and press ENTER.
To exit without storing setting, select Cancel.
Select Source Name and press ENTER to dis-
play the Source Name Edit window. You can
change source name on this window. Press [H]
to display the software keyboard, which you can
enter alphanumeric characters. See page E-84
for the key function of the software keyboard.
All Delete ..... This feature enables you to delete all the regis-
tered signals in the Entry List.
The following buttons are not available for the currently project-
ing signals:
1) The Cut and Paste buttons on the Entry Edit Command screen
2) The Input Terminal button on the Entry Edit screen
Adjust (Source)
Picture
Brightness
Adjusts the brightness level or the back raster intensity.
Contrast
Adjusts the intensity of the image according to the incoming
signal.
Saturation
Adjust saturation at the white peak.Colour
Increases or decreases the colour saturation level (not avail-
able for RGB).
Hue
Varies the colour level from +/- green to +/-blue. The red level
is used as reference. This adjustment is only valid for Video
and Component inputs (not available for RGB).
Sharpness
Controls the detail of the image for Video (not available for
RGB).
Setup Level
“7.5 IRE” must be chosen to project products manufactured in
USA.
Video Adjust (not available for RGB)
Noise Reduction
Select one of the three levels for reducing video noise: Low, Me-
dium or High.
NOTE: The lower the Noise Reduction level, the better the image quality by way ofhigher video bandwidth.
Colour Matrix
Select an appropriate colour matrix for your input signal, either
HDTV or SDTV.
Y/C Delay
Adjusts Y/C delay level.
YTR Adjustment
Adjusts luminance transient time.
CTR Adjustment
Adjusts chroma transient time.
6. Using On-Screen Menu 
						

							E-52
DigiView - Enhanced Contrast
The Enhanced Contrast feature provides improvement of con-
trast using a proprietary detail enhancement technology.
This is valid when there is signal input to MM-VIDEO and to the
MM-SDI (option).
NOTE: This feature is not available for 480p, 576p and HDTV signals.
Telecine
Use 3:2 pull down correction to eliminate jitter and artifacts in
video.
Auto ............. For film source such as a DVD player
2:2 Off ......... The telecine signal detection and compensation
will be performed automatically only when the
2:3 pull-down signal is input. Select this when
entrance is not desired to the 2:2 pull-down sig-
nal detection mode.
Off ............... For signals other than film sources
NOTE: This feature is not available for 480p and 576p signals.
3D Y/C  Separation
This option turns on or off the 3 dimension separation feature.
NOTE: This feature is available for NTSC3.58 of Video signal only.
Vertical Detail Correction
Horizontal line on picture signal can be sharpened by increasing
setting value.
NOTE: This feature is not available for RGB signal.
Colour Management
Colour Management
Setup relating to picture colour will be done.
Vivid palette, pastel vision, colour temprature and white balance
can be adjusted as your choice.
Each set value is saved as exclusive use of projected signal set
value, and also those can be saved as default value for this equip-
ment.
Colour Correction (Item relating to colour adjustment)
Adjusts red, green, blue, yellow, magenta, cyan and colour gain
each independently to correct the tint on whole screen.
Colour Temperature (Item relating to colour adjustment)
This feature adjusts the colour temperature using the slide bar.
Checking Colour Temperature enables the colour temperature
slide bar.
White Balance (Item relating to colour adjustment)
Press the White Balance button to access the Contrast/Bright-
ness adjustment for each R, G, and B.
Return to Reference (Item relating to colour adjustment)
• Each set value of colour correction, colour temperature and
white balance is reset. (Set back to this equipment’s default
value)
• Point the cursor to “Reset” and ENTER button is pressed, con-
firmation screen shows up. Point the cursor to “Confirm” and
ENTER button is pressed, the set value is set back.
NOTE:
• Once the RESET is excuted, undo can’t be done even CANCEL on colour manage-
ment screen is excuted.
Set Custom (Item relating to set value memory)
Each set value for colour correction, colour temperature and white
balance can be saved to memory as exclusive use of currently
projected signal set value. The screen is shut down after saving.
Set Reference (Item relating to set value memory)
Each set value for colour correction, colour temperature and white
balance can be saved to memory as this equipment’s default
value (the value set when reset). The screen is shut down after
saving.
Cancel (Item relating to set value memory)
Each set value for colour correction, colour temperature and white
balance screen is shut down without saving set value to memory.
Each set up is set back to status before colour management
screen is opened.
Gamma Correction
Gradation of picture is selected. By doing this, dark parts can be
expressed clearly.
Graphics Enhanced ............. Correction fit to graphic signals
is done.
Graphics/NTSC ................... Corrections fit to graphic signals
and NTSC signals are done.
NTSC Enhanced ................. Correction fit to NTSC signals is
done.
PAL/SECAM2.8 ................... Gamma correction value 2.8 is
corrected.
6. Using On-Screen Menu 
						

							E-53
Synchronize
Sets display vertical frequency to be synchronized with input sig-
nal.  RGB signals only.
OFF ............. Display vertical frequency - is independent of in-
put signal - displayed picture is fixed at 75Hz.
ON ............... Display vertical frequency - is synchronized with
input signal.  Frequency range of synchroniza-
tion is from 24Hz to 96Hz.
If Vertical frequency is outside the range of 24Hz
to 96Hz, set OFF
When a horizontal line (at the edge of picture) is
displayed on the screen, perform “Adjust”.
If “ON” is set for (Synchronize) when the optional
MM-WARP is used and the vertical frequency of
input signal ranges from 76Hz to 96Hz, no im-
ages can be displayed in the native resolution,
but they must be resized.
ADJUST ...... When a horizontal line (the edge of picture) is
displayed on the screen while Synchronize is
“ON”  it can be removed using SELECT F E
button on the remote controller.
Note: Default is Synchronize ON for SDTV, HDTV, RGB 50Hz, 60Hz signals.
Video Filter
This function reduces video noise.
Off ............... The filter is removed.
Less ............. The low-pass filter is applied partially.
More ............ The low-pass filter is applied fully.
Blanking
This feature allows you to mask any unwanted area of the screen
image.
Adjust the Top, Bottom, Left or Right blanking with the SELECT
F or E button.
Input Resolution
This adjusts the resolution of the video area of the signal that is
input to the resolution conversion processing section. When the
resolution of the input signal cannot be detected properly with
Auto Adjust, this function can be used to manually set the correct
resolution. PAL/SECAM Enhanced ....... Correction fit to PAL signals and
SECAM signals are done.
Gamma 1.0 - 3.0 ................. Gamma value is set by 0.1 step.
Note:
If [Edge Blending] is “On”, [Gamma Correction] is not available
and greyed out.  At this time, the gamma correction value is fixed
to the value set in [Gamma] on [Edge Blending] screen.
Image Options
Pixel Adjust
Displays the Clock and Phase adjustments.
Clock ........... Use this item to fine tune the computer image or
to remove any vertical banding that might ap-
pear.
Phase .......... Use this item to adjust the clock phase or to re-
duce video noise, dot interference or cross talk.
(This is evident when part of your image appears
to be shimmering.) Use the SELECT F and E
buttons to adjust the image.
Use Phase only after the Clock is complete.
Position
Adjusts the image location horizontally and vertically using the
SELECT F and E buttons.
Aspect Ratio
You can select the aspect ratio for input signal.
Select the appropriate aspect ratio using the SELECT F or E
button.
NOTE:
• When Resolution is set to Native, this feature is not available, and the aspect
ratio is set to “1.33:1 (4:3)”.
Resolution
This allows you to activate or deactivate the Advanced AccuBlend
feature.
Auto ............. Turns on the Advanced AccuBlend feature. The
projector automatically reduces or enlarges the
current image to fit the full screen.
Native .......... Turns off the Advanced AccuBlend feature. The
projector displays the current image in its true
resolution.
NOTE:
* When Resolution is set to Native, Aspect Ratio, Screen and Overscan are
not available.
Overscan
Select overscan percentage (0%, 5%, 8% and 10%) for signal.
NOTE: When Resolution is set to Native, this feature is not available, and thestored settings and adjustments are invalid.
6. Using On-Screen Menu 
						

							E-54
Input Position
This adjusts the position of the video that is input to the resolu-
tion conversion processing section.
It is the same function as “Input Position” within the “Edge Blend-
ing” screen.
Output Position
This adjusts the image output position on the display panel.  If
the image is displayed smaller than the allowable image area of
the projector (such as native resolution), this output can be ad-
justed as needed.
Option Adjust
Clamp Timing
According to the signal, this function sets the detection position
(i.e., clamp position) of the black level reproduction of the analog
input signal. Normally this is not used.
Mode 0-4 ..... Select the appropriate one.
Adjust .......... This permits the video clamp position for each
signal to be set. Use Adjust when a clamp tim-
ing error occurs at the time of special analog sig-
nal reception such as 1080P. Note that Adjust
is not valid for doubler signals such as NTSC
and PAL.
To delete the Clamp Timing setting screen, select the SELECT
H button and press the ENTER button, or press the remote con-
trol CANCEL button.
Sync Protection
When a VCR, DVD, or some other equipment that supports
Copyguard (a copy prevention system) is played back, the screen
may be displayed in a curved manner. Adjustments are made in
such circumstances. Use the SELECT F or E button to adjust
the VD level.VD Delay
Adjustment:
This feature is used to correct vertical jitter of a signal.
NOTE: When connecting with a scan converter:
If an image from the scan converter is not correctly displayed, adjust to select the
best level point so that the image is displayed correctly.
Field Invert: (Upgrade support scheduled)
This feature is used to correct diagonal lines of a non-standard
interlaced signal when they appear jaggy.
Invert the odd or even field of a video signal.
Signal Level
R/G/B, Y/Cb/Cr or Y/Pb/Pr Gain:
Adjust RGB, Component or HDTV Gain to match multiple pro-
jector colour uniformity.
Lens Memory
This function serves to store or apply the adjusted value when
using the Shift, Focus and Zoom buttons on the projector or the
remote control.
Set Custom Point ........... Store the current adjusted values in
memory.
Use Custom Point .......... Apply the adjusted values to the cur-
rent signal.
6. Using On-Screen Menu 
						

							E-55
6. Using On-Screen Menu
NOTE:
• To enable the Lens Memory feature, select [Ref. Adjust] → [Ref. Lens Memory]
and place a check mark next to “Yes” for [Use Point on Signal Change?].
• To store adjusted values common to all the input sources, use the Ref. Lens
Memory. See page E-56.
Signal Type
Select either the RGB signal type or the Component signal type.
RGB ............ RGB signal
Component .. Component signals such as Y/Cb/Cr, Y/Pb/Pr
NOTE: This feature is available on RGB only. If you do not get a better picture evenwhen you set Signal Select to Component in Setup, set this to Component.
Ref. Adjust
3D Reform
This feature corrects trapezoidal distortion so that the projected
image is rectangular.
Operation of 3D Reform is available whether MM-WARP (optional)
is used or not.
MM-WARP- not installed or not active
When MM-WARP is not installed (optional) or installed but not
active only vertical adjustment in Keystone Correction is pos-
sible.
(For de-activation set no check mark on “Projector Options” →
“Setup” → “page 3” → “WARP Correction”.)
Keystone Correction
1. Press SELECT Button - Adjust screen size in vertial direction.
2. Press ENTER Button after adjusting screen size - Return to the menu.
MM-WARP - active
When MM-WARP (optional) is installed and active both vertical
and horizontal adjustment in Keystone Correction is possible.
(To activate set check mark on “Projector Options” → “Setup” →
“page 3” → “WARP Correction”.)Keystone Correction
1. Press SELECT Button - Adjust screen size in horizontal direction.
2. Press SELECT Button - Choose “Vertical”.
3. Press SELECT Button - Adjust screen size in ver tical direction.
4. Press ENTER after adjusting screen size. - Return to the menu.
Cornerstone
1. Project an image so that the screen is smaller than the area of the
raster.
2. Pick up any one of the corners and align the corner of the screen with
the one of the image.
Screen
Projected image
Screen (The drawing shows the upper right corner.)
3. Use the SELECT 
GHFE button to select one icon which points in the
direction you wish to move the projected image frame. 
						

							E-56
4. Press the ENTER button.
5. Use the SELECT 
GHFE button to move the projected image frame as
shown on the example.
6. Press the ENTER button.
6. Using On-Screen Menu
• The indicated adjustment ranges are following;
Horizontal direction ....± 30 degrees (maximum)
Vertical direction ........± 40 degrees (maximum)
• When horizontal and vertical adjustment is occured at a time, the adjustment
range will be narrower.
• Curved Line Warp Correction
Only linear screen warp is adjusted by Cornerstone Correction. Curved screen
adjustment to correct  for lenses or screens (cylindical or spherical) can be ad-
justed by an application software, Geometric Correction Tool.
The Geometric Correction Tool is available from Digital Projection please contact
your dealer.  Geometric Correction Tool version 2.0.3 or higher is recommended.
Screen
Screen Type
Select the correct aspect ratio for the screen to be used.
See also Aspect Ratio on page E-53.
NOTE:• When Resolution is set to Native, this selection is inactive.
Position
This feature adjusts the vertical position of the image when view-
ing video with an aspect ratio selected.
When some aspect ratios are selected in Image Options, the
image is displayed with black borders on the top and bottom.
You can adjust the vertical position between top and bottom.
NOTE: This option is available only when 1.78:1 (16:9), 1.85:1 and 2.35:1  areselected in Screen Type and Aspect Ratio.
Ref. Lens Memory
This function serves to store the adjusted value common to all
input sources when using the Shift, Focus, and Zoom buttons of
the main unit or the remote control.
Set Reference Point ............. Stores the current adjusted val-
ues in memory as a reference.
Use Reference Point ............Applies the adjusted values
stored in Set Reference Point to
the current signal.
Return to Factory Default ..... Returns the adjusted values to
the factory default setting.
Use Point on Signal Change? ....For change to take effect at the
time of source selection, select
“Yes”.
Picture Mute during Lens Shift? ...To turn off the image and sound
during lens shift, select Yes.
Screen
Screen 7. Use the SELECT 
GHFE button to select another icon which points in
the direction.
8. Repeat 4-7.
9. On the Cornerstone adjustment screen, select “Exit” and then press
the ENTER button.
The confirmation screen is displayed.
10. Press the SELECT F or E button to highlight the [OK] and press the
ENTER button.
This completes the keystone correction.
Selecting “Cancel” will return to the adjustment screen without saving
changes (Step 3).
Selecting Reset will return to the factory default.
Selecting Undo will exit without saving changes.
NOTE:
• In the case “Resolution” is set as “Real”, “3D Reform” can’t be chosen.
• In the case keystone warp is adjusted by “3D Reform”, “Aspect” or “Screen Setup”
can’t be changed in some case. In such a situation, “3D Reform” adjusting value
must be reset first and each setup must be changed. After that keystone warp
should be changed again.
• In the case using MM-WARP (optional), some internal part of picture signal will
be 8 bit process.
• Ask the shop this equipment was purchased when MM-WARP (optional) imple-
mentation is necessary.
• In the case Keystone Correction’s vertical setup value is adjusted when MM-
WARP is not in use, the data will be reflected when MM-WARP is used, however,
adjustment content will be different. Re-adjust setup value as circumstance de-
mand.
• When 3D Reform is done, picture quality is degradated comparing to no
adjustment done.
Also, when screen is warped in a large scale, the noises occasionaly show up
on the screen.
NOTE:
• “3D Reform”’s adjustment value is saved even this equipment is OFF. To restore
    the adjustment value to factory default setting, press “Keystone Button” on the
    remote controller for more than 2 seconds.
• Press the remote controller’s “Keyston Button” while “3D Reform” screen is ac-
tivated. Each time the button is pressed, [Cornerstone] screen and [Keystone]
screen are shown one after another. 
						

							E-57
NOTE: This option is only available when
Yes is selected for Use Point on Signal
Change?.
Even if “CANCEL” is executed, changes to “Set Reference Point”,
“Use Reference Point” and “Return to Factory Default” will not be
canceled.
* See Tips on Adjusting Focus on page E-31 for more information.
NOTE:
• Adjusted values in Ref. Lens Memory will not be returned to default by using the
Factory Default.
• To store adjusted values for each input source, use the Lens Memory.
NOTE: In the Link mode the Lens Memory feature is not available.
Edge Blending
When two or more projectors are used to project images lined up
horizontally or vertically, a blending adjustment can be performed
to make the borders of the adjacent images less conspicuous.
This description is of an adjustment example in which 2 Projec-
tors are used to project images side-by-side.
Preparation:
Set the lens position of each projector as close to centre as pos-
sible. If projection is not central in the lens then some image dis-
tor tion may occur and images from two projectors may not be
successfully superimposed.
Making the image quality of each projector as uniform as pos-
sible will allow the screen edges (boundaries) to be less
conspicious.
- Installing the projector
Using the test pattern “Cross Hatch” in the projector, superim-
pose the images so that the height of the two projected images is
the same and distortion does not appear.  If the number of pixels
6. Using On-Screen Menu
in the superimposed area has been determined in advance, the
blending correction range can be easily adjusted in the following
bending correction.
- Adjusting the range of the superimposed area (blending correction range)
This adjustment is saved as Ref. Adjust data for the projector.
(1) Select “ON” in the [Edge Blending] - [Page 1] screen.
(2) From among the 4 location of ▲ marks on the [Edge Blending] -
[Page 1] screen, move the cursor to the ▲ mark that is the same
direction as the side on which you would like to perform blending
correction of the projector’s projection screen.
•In the example above, select the E mark in the left projector to adjust
the right side of projected image, and select F mark in the right
projector to perform blending correction on the left side of the right
projector.  Next press ENTER button.
(3) Perform blending correction for the left hand edge of the Right
projector.
Use F to adjust the blend of the Right projector and press ENTER.
•To change the number of pixels in the superimposed area, input a
new value using the Remote Control numeric buttons, then press
ENTER.
If this value is not cer tain, align the marker on the projected image to
determine the blending range and press ENTER.
Projected areaProjected area Overlapping areaOverlapped cells 
						

							E-58
(4) Perform blending correction for the Right hand edge of the  Left
projector.
Use E to adjust the blend of the left projector and press ENTER.
• To change the number of pixels in the superimposed area, input the
same value as used in (3) above using the Remote Control numeric
buttons, then press ENTER.
This value can also be adjusted using F
 or E, on the remote control.
- Adjusting the lens shift
Fine position adjustment of the images projected is allowed. This
adjustment is saved as Ref. Adjust data.
1. On the [Edge blending] - [Page 1] screen, select “Lens Shift”.
- [Lens Shift] screen appears.
2.  Using the SELECT button on the remote control, adjust the
positions of the projected images.
- Set the adjustment value to a minimum. A larger value may warp
images, and the superimposed area may not be correctly adjusted.
3. After the lens shift adjustment is completed, press the CANCEL
button.
- The screen goes back to [Edge Blending] - [Page 1] screen.
- Adjusting the black level
If two projectors are used for projection, the superimposed areas can
appear brighter with no input signal.
Adjust the black level of the non-superimposed area to be as bright
as the superimposed area, so that even with no signal input, the
brightness of the whole screen is the same.
This adjustment is saved as reference setting data in the projector.
(1) Select “Black Level” in the [Edge Blending] - [Page 1] screen.
Image disappears, and the adjustment bar is displayed.
(2) Adjust the screen brightness evenly using the G  H F  E buttons on
the remote controller. G
 H buttons: Increases/Decreases the correction value in steps of
10.
F
  Ebuttons: Increases/Decreases the correction value in steps of 1.
Adjust the brightness of the dark part (non-superimposed area) and
that of the bright area (superimposed area) so that the whole screen
brightness is even.  Before this adjustment, perform (1) for each
projector.
To perform edge blending when two or more projectors are used,
adjust the brightness in the same way so that the brightest
superimposed area is as bright as the non-superimposd area.
(3) Press the ENTER button when the adjustment of black level has
been completed.
[Edge Blending] - [Page 1] screen reappears.
- Setting the “Keep Marker” check box
Check this box to display the marker even after the [Edge Blending]
screen is exited.
1. On the [Edge Blending] - [Page 1] screen, check the “Keep Marker”
check box, and press the ENTER button.
- The check box is checked.
- The marker is displayed even after the [Edge Blending] screen is
exited.
- If the projector is placed on standby, the check box is automatically
unchecked.
 - Adjusting the image output range and position
Adjust the output range and position of images projected by each
projector when two projectors are used to display one combined-
image. Connect the desired video signals to two projectors, and
adjust the following while projecting the images.  This adjustment is
possible per signal.
(1) In “Input Resolution” on the [Edge Blending] - [Page 2] screen, adjust
the area for each projector to display.
In the example, two projectors display the left and right half
respectively.  Enlarge each half using the horizontal adjustment bar.
(2) In [Input Resolution] on the [Edge Blending] - [Page 2] screen, adjust
the output position of images to be enlarged through each projector.
6. Using On-Screen Menu 
						

							E-59
6. Using On-Screen Menu
(3) Adjust the settings in (1) and (2) so that images on the screen are
superimposed.
(4) Select “Adjust (Source)” → “Image Options”  → “Blanking” of the
Advanced Menu and hide the left and right unrequired portions of the
screen as required.
- Checking the “Black Label Only” check box
If images are displayed by two or more projectors together, blending
correction is necessary.  On the other hand, if images are separately
displayed by each projector, blending correction must be set to “OFF”.
Checking the [Black Level Only] check box in the [Edge Blending] -
[Page 2] screen is assumed that blending correction is off and only
the black level correction is allowed.  This adjustment is possible per
signal.
Note:
In edge blending, when the projector displays images in full size on the
screen, the four edge lines of the screen are the standard (correction
range value is 0) position to fix the blending correction range.
Blending correction can’t provide the optimal images when projected
image is smaller than full size screen according to setting of the Screen
Setup (Page 83) and Aspect setup (Page 76).
If blending correction is “ON”, “Gamma” of images is fixed to the gamma
value displayed on the [Edge Blending] screen.
HL12000HD and HL10000HD projectors enable the edge blendingfunctions only when selecting an advanced menu, [Ref. Adjust]  →
[Screen], and “1.90:1” as the screen type.
Set “16:9” as the screen type in [Screen] when MM-WARP option is
used.
Lamp Mode
Lamp brightness can be adjusted to 8 levels or automatically
adjusted.
Adjust .......... Choices of levels: 65%, 70%, 80%, 85%, 90%,
95%, 100%
Auto ............. Automatic adjustment is made when “ON” is se-
lected.
Auto maintains same power after a power cycle.
Factory Default
All Data /Current Signal
The Factory Default feature allows you to change adjustments
and setting to the factory preset for source.
All Data ........ Reset all the adjustments and settings for all the
signals to the factory preset except Language,
Background, Communication Speed, Projector
ID, LAN Mode, Password and Security.
Including Entry List:
Also deletes all the signals in the Entry List and
returns to the factory preset.
NOTE: Locked signals in Entry List cannot be deleted.
Current Signal
.................... Resets the adjustments for the current signal to
the factory preset levels.
All the items in Adjust (Source) can be reset.
NOTE: Locked signals in Entry List cannot be reset.
Blending area
Blending correction is necessar y
Black level correction is necessar y
Blending area
Blending correction is unnecessary
Black level correction is necessary
Adjust the image size and position by setting
[Resolution], [Input Position] and [Output position] in Image Options. When images from two projectors
are displayed in combination:
When images from two projectors
are displayed separately:Left image
Right image
Left image
Right image 
						

							E-60
Projector Options
Menu
[Page 1]
Selecting Menu Language [Language]
You can choose one of seven languages for on-screen instruc-
tions. The options are: English, German, French, Italian, Span-
ish, Swedish and Japanese.
Selecting Menu Mode [Menu Mode]
This feature allows you to select 4 menu modes: Advanced,
Custom, Basic and Service Menu.
Advanced Menu ...... This is the menu that contains all the
available menus and commands.
Basic  Menu ............. This is the basic menu that contains mini-
mum essentials of menus and com-
mands.
Custom  Menu .......... This is the menu that you can customize
using the Custom Menu Edit to fit your
needs.
Service Menu .......... For service personnel only.
Customizing the Menu [Custom Menu Edit]
See page E-44 for instructions about how to customize the
Menu.
Selecting Menu Display Time
This option allows you to select how long the Projector waits
after the last touch of a button to turn off the menu.
The preset choices are Manual, Auto 5 sec, Auto 15 sec,
and Auto 45 sec. The Auto 45 sec is the factory preset.
Manual ........ The menu can be turned off manually.
Auto 5 sec ... The menu will automatically be turned off in 5
seconds if no buttons are pressed within 5 sec-
onds.
Auto 15 sec . The menu will automatically be turned off in 15
seconds if no buttons are pressed within 15 sec-
onds.
Auto 45 sec . The menu will automatically be turned off in 45
seconds if no buttons are pressed within 45 sec-
onds.Selecting Date Format
Eight display formats can be selected. This date format sets
the current date that appears on the upper left corner of the
screen.
Setting the Current Date and Time [Date, Time Preset]
You can set the current time, month, date, and year.
1. Type in date.
Enter month, date and year in this order using Source/Input buttons on
the remote control.
Month and date must be entered in two digits. For example, to display
February, press 0 and 2.
2. Type in time.
Time is expressed in the 24-hour format. For example, 6:00 p.m. is en-
tered as 18:00.
3. Select OK and press ENTER.
Closing the window allows the clock to start.
The current year, month, date and time are displayed on the top of the
screen.
NOTE: The Projector has a built-in clock. The clock will keep working for about 2
weeks after the main power is turned off. If the main power is off for 2 weeks or
more, the built-in clock will cease. If the built-in clock ceases, set the date and time
again. The built-in clock will not cease while in the standby condition.
[Page 2]
Display Select
You can choose the desired status information to be displayed
on the screen.
The information selections are:
Date, Time, Input Terminal, Source Name, Projector ID and
Message.
The Message selections are:
“Wait a moment”.
6. Using On-Screen Menu