Digital Projection Highlite 16000Dsx+, Highlite 10000dsx+ Users Manual

							E-31
ON
TESTABC1DEF2GHI3
JKL4MNO5PQR6
STU7VWX8
0YZ /9 POWER INPUT
OFF
IMAGE/PROJECTORON
OFFPICTURE
ADJUSTWHITE BAL.
ENTER
CANCEL UNDOAUTO
MAGNIFY/FOCUS  +ZOOM  +
MENU/ADDRESS
MUTE
3. Projecting an Image
2 Selecting a Source
Selecting the computer or video source
Using the Remote Control
Press the Source/Input button
(1-4) to select input.
1 ...... Slot 1
2 ...... Slot 2
3 ...... Slot 3
4 ...... Slot 4
NOTE: If no input signal is available, the Projector will display a blue background(factory preset).
ENTER
CANCEL UNDOAUTOHELP ON
TEST
ABC1DEF2GHI3
JKL4MNO5PQR6
STU7VWX8
0YZ /9 POWER INPUT
OFF
INFO
PIXEL SOUNDOSD
MAGNIFY/
CTL
FOCUS  +
-
ZOOM  +
MENU/ADDRESS
IMAGE/PROJECTOR
POSI/LENS
KEY ST./
ON
OFF
RE-LIST/ PICTURE
ADJUST
WHITE BAL.
BAMP/G
PICT/SHUT
-
MUTE
Using the menu
You can also select the computer or video source using the menu.
3 Adjusting the Picture Size and Position
1. Turn on the projector
2. Select your type of projector orientation.
Desktop front, ceiling rear, desktop rear, and ceiling front.
3. Display the test pattern by pressing the TEST button on the remote
control or using the menu.
4. Adjust the image position and the image size.
(1) Press and hold the CTL button and press the POSITION button to
display the Lens Shift adjustment screen.
Use the SELECT button on the remote control or the LENS SHIFT
button on the projector cabinet to move the image horizontally and
vertically.
To close the Lens Shift adjustment screen, press the CANCEL
button. See page E-23 for “Lens Shift Adjustable Range”.
ENTER
CANCEL UNDO
MAGNIFY/FOCUS  +ZOOM  +
MENU/ADDRESS
AUTOHELPINFO
PIXEL SOUNDOSD
MENU/ADDRESS
POSI/LENS
KEY ST./RE-LIST/BAMP/G
PICT/SHUT
MUTE
CTL-- 
						

							E-32
3. Projecting an Image
(2) Press and hold the CTL and press the ZOOM + or - button to adjust
the image size.  You can also adjust the image size by using the
CTR button and the ZOOM + or - button on the projector cabinet.
(3) Press and hold the CTL button and press the FOCUS + or - button
to obtain the best focus. You can also adjust the focus by using the
CTR button and the FOCUS + or - button on the projector cabinet.
Geometric Correction Tool
If you use a special shaped screen such as a cylindrical or
spherical screen, a downloadable program, Geometric Cor-
rection Tool is available. This program (Geometric Correc-
tion Tool) enables the geometrical distortion correction of
an image when projected onto a special shaped screen with
the projector. Additionally, this program allows control of the
projector via a computer.
For additional information contact your dealer or Digital Pro-
jection:
US : [email protected]
Europe : [email protected]
Global : [email protected]
CANCEL
MAGNIFY/
CTL
FOCUS  +
-
ZOOM  +
-
CANCEL
MAGNIFY/
CTL
FOCUS  +
-
ZOOM  +
- 
						

							E-33
ON
TESTABC1DEF2GHI3
JKL4MNO5PQR6
STU7VWX8
0YZ /9 POWER INPUT
OFF
IMAGE/PROJECTORON
OFFPICTURE
ADJUSTWHITE BAL.
5 Turning off the Projector
To turn off the Projector:
First press the POWER (ON/STAND BY) button on the Projector
cabinet or the POWER OFF button on the remote control for a
minimum of 1 second. The POWER indicator will glow orange.
Second, turn off the Main Power switch. The power indicator will
go out.
Last unplug the power cable.
CAUTION
• When switching off the Main Power switch, set the Pro-
jector to the standby mode beforehand. Values that have
been set with the on-screen menu or by other means might
not be stored in the main unit if the Projector power sup-
ply is on when the Main Power switch is switched off.
• Do not unplug the power cable from the wall outlet or do
not turn off the main power under any one of the follow-
ing circumstances. Doing so can cause damage to the
Projector:
* While the Hour Glass icon appears.
* While the message Please wait a moment. appears. This mes-
sage will be displayed after the Projector is turned off.
* Immediately after the main power switch has been turned ON.
(When the POWER indicator is not lit in orange, and before
“Stand by” is displayed on the liquid crystal display screen.)
* Immediately after the end of the cooling down period (during
which the fan is running for 3 minutes after the POWER button
has been switched OFF, and before “Stand by” is displayed on
the liquid crystal display screen).
Steady green
lightSteady orange
light
3. Projecting an Image
ENTER
CANCEL UNDOAUTOHELPINFO
PIXEL SOUNDOSD
MAGNIFY/FOCUS  +ZOOM  +
MENU/ADDRESS
POSI/LENS
KEY ST./RE-LIST/BAMP/G
PICT/SHUT
MUTE
4 Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing RGB image automatically
1. Press the AUTO button on the remote control to optimize an RGB im-
age automatically.
[Poor picture] [Normal picture]
Press the AUTO button to fine-tune the computer image or to
remove any vertical banding that might appear and to reduce
video noise, dot interference or cross talk (this is evident when
par t of your image appears to be shimmering). This function ad-
justs the clock frequencies that eliminate the horizontal banding
in the image. This function also adjusts the clock phase to re-
duce video noise, dot interference or cross talk. (This is evident
when part of your image appears to be shimmering.)
This adjustment may be necessary when you connect your com-
puter for the first time.
NOTE:
• Some signals may not be displayed correctly or take time.
• The Auto Adjust function does not work for component and video signal.
• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock
and Phase manually. See page E-53.
The Auto Adjust menu is displayed.
2. Select “Input Resolution” and change the “Horizontal” number of pixels
and number of “Vertical” lines as required.
3. Align the cursor with “OK” and press the ENTER button.
Standby Power on
POWERPOWERON/STAND BY
NOTE:
• The Auto Adjust operation alone does not automatically store the adjusted values
in memory.  To store the adjustments, use the operations of the Entry List.  For
details, see “6-3 Source Select, Entry Edi Command” on page E-50. 
						

							E-34 
						

							E-35
4
Convenient Features
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
1 Turning Off the Image ............................................ E-36
2 Getting the On-line Help and Information .............. E-36
3 Lens Memory ......................................................... E-36 
						

							E-36
1 Turning Off the Image
Press the MUTE PICTURE button to turn off the image for a
short period of time. Press again to restore the image.
Press the MUTE OSD button to turn off the on-screen display.
Press again to restore the on-screen display.
NOTE: You can also turn off the on-screen display forcibly by pressing and holding
CTL and then pressing MUTE OSD (Forced On-Screen Mute Mode) ; doing this
again restores it. In this case any adjustment will still change the projectors memory
settings. This mode is available even when input is switched to another or the main
power is turned off.
2 Getting the On-line Help and Information
You get the contents about Help.
Display Help
You get the source and projector information.
Press this button once to display “Source Information” and press
twice to display “Projector Information”.
Press third time to close it.
AUTOHELPINFO
PIXEL SOUNDOSDPOSI/LENS
KEY ST./RE-LIST/BAMP/G
PICT/SHUT
MUTE
AUTOHELPINFO
PIXEL SOUNDOSDPOSI/LENS
KEY ST./RE-LIST/BAMP/G
PICT/SHUT
MUTE
This function serves to store the adjusted value when using the
Shift, Focus, and Zoom buttons of the projector or the remote
control.
Reference memory:
Reference Point ...... Adjusted settings are stored in memory
as a reference common to all the input
sources. If no setting is stored in Cus-
tom Point, the adjusted settings in Ref-
erence Point will be applied.
Custom memory:
Custom Point ........... Adjusted settings are stored in memory
for each input signal.
Usage Example
When you wish to display on a screen having a 4:3 aspect ratio
an NTSC or other 4:3 aspect ratio signal and an SXGA or other
5:4 aspect ratio signal:
Perform shift, focus, and zoom adjustments to set the vertical
screen size of the vertically tall 5:4 aspect ratio signal to stan-
dard.
Both 4:3 apsect ratio signals and 5:4 aspect ratio signals can
now be displayed.
Note that with these shift, focus, and zoom adjustments, the 4:3
aspect ratio signal will become smaller on the screen.
To eliminate this size reduction, adjust the shift, focus and zoom
to the optimum condition for each of the 4:3 aspect ratio signal
and the 5:4 aspect ratio signal. Memory (storage) of each of these
values will permit projection at an optimum condition upon signal
switching.
1. Perform Zoom, Focus and Lens Shift adjustments and store
them in memory using “Set Custom Point”.
Another way to store your adjustments is to use the CTL and
INFO buttons on the remote control.
2. When “Yes” is selected for “Use Point on Signal Change”, the
adjustment is applied to the signal you switched.
3. Select “OK” and press the ENTER button for the change to
take effect.
Picture Mute during Lens Shift?
To turn off the image during lens shift, select Yes.
NOTE: This option is only available when Yes is selected for Use Point on SignalChange?.
3 Lens Memory
4. Convenient Features 
						

							E-37
5
Setting Up for Double Stacking
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
1 Stacking and Connecting the Projectors ............... E-38
2 
Adjusting and Registering Signals to Be Projected....... E-42
3 Adjusting the Lens Shift, Zoom and Focus
to Clearly Display all projected patterns ................ E-42 
						

							E-38
5. Setting Up for Double Stacking in Link Mode
1 Stacking and Connecting the Projectors
Master projector
Slave projector
NOTE: Up to two units can be gravity stacked without external support. In some
cases, however, two images will not align on the screen correctly. This will become
more apparent when displaying small text and detailed graphics.
NOTE: The frame is not supplied on HIGHlite 10000Dsx+.
CAUTION: To prevent the projectors from falling, install them in a place and fasten them in away with sufficient strength to support the two projectors.
1-1. Frame Connection (HIGHlite16000Dsx+)
2. Lift the projector of feet.
Master Projector
Slave Projector
Button
Ball-lock Pin
1. Press Button to
    remove Ball-Lock Pin
Remove feet from projector to be mounted on top of stack. 
						

							E-39
1-2. Frame Adjustment (HIGHlite16000Dsx+)
• Tilt Angle Adjustment
Knurled knobs (A, B on the
picture at the left) are turned
to the same direction. (note 1)
• Roll Angle Adjustment
Knurled knobs (B, C on the
picture at the left) are turned
to the same direction. (note 1)
• PAN Angle Adjustment
Knurled knob (S) (Enlarged
picture at the left) is turned.
Knurled knob(S)Knurled knob
Enlarged
Screen
Screen
Screen
note 1: when Knurled knobs at two locations are turned, the same charge shouldbe turned.
1-3. Assigning Projector IDs
You can operate multiple projectors with the same remote con-
trol.
To do so:
Master Projector
Slave Projector
3. Stack projectorsJoin using stacking
connectors
Master Projector
Slave Projector
4.  Insert all four Ball-lock Pins back into
     stacking connectors 
Place projectors together.Connect projectors using Ball-lock Pins.
5. Setting Up for Double Stacking in Link Mode 
						

							E-40
5. Setting Up for Double Stacking in Link Mode
13-1. Select “Projector Options” → “Setup” → “Page4” → “Pro-
jector ID” and assign an ID number to each projector. See also
page 8-18.
1-3-2. Select the same communication speed for both the pro-
jector.
NOTE: Do not turn on [Master] or [Slave] at this time.
 2  1
S-VIDEO
S-VIDEO
OUTPUT INPUT
AUDIO OUT VIDEO OUTLRS-VIDEOVIDEO
S-Video cable
(not supplied)
S-VIDEO
S-VIDEO
Signal Divider
Picture Device
Master projector
Slave projector
According to signal dividers, the port 
name, location and aspect are different. 
Please check the signal dividers 
instruction manuals.
According to picture devices, the port 
name, location and aspect are different.
Please check the picture devices 
instruction manuals.
S-Video cable (not supplied)
1-3-3. On the remote control specify the ID number of the pro-
jector to be adjusted. Press and hold the CTL and press
MENU (ADDRESS) button to enter the ID number.
You can operate the projector assigned the same ID number
as the remote control.
NOTE: Specifying None for projector ID allows you to operate multiple projectors
concurrently. However, some projectors may not synchronize to the other projec-
tors.
1-4. Stacking the Projectors
Place the projectors at the proper height for best screen to pro-
jector relationship. Make sure that all projectors have the same
display orientation.
1-5. Cable Connection
Example on Video Signal
Picture signal is divided by commercial signal divider, and connected to both master projector’s and slave projector’s input ports.