Digital Projection Highlite 14000hd Users Manual

							E-71
(3) When you attempt to display an image for which security is set
while the security function is enabled
• Blanks (spaces) cannot be used in the Keyword section.
To delete PC card data you registered.
1. Use the SELECT GH button to select Delete and use the SELECT Fbutton to select the list window.
2. Use the SELECT 
GH button to select the PC card data you wish to
delete.
3. Press the SELECT 
E button to select Delete and press the ENTER
button.
The PC card data will be deleted.
If youve lost your registered PC card, proceed as follows:
NOTE: your dealer will provide you with your Release Code in exchange for yourregistered keyword and Request Code. See URLs at the end of this section.
1. Press and hold the POWER button for a minimum of two seconds.
The projector will be turned on and display a message to the effect that
the projector is security-protected.
2. Select [Projector Options] 
→ [Security] from the menu and press hte
ENTER button.
The Release Code input screen will be displayed as well as your Re-
quest Code (24 alphanumeric characters).
3. Enter your Release Code in the Release Code Input screen.
* If the projector is turned on by entering the Release Code, your Secu-
rity will be disabled.
NOTE:
* Some types of PC cards cannot be registered as your protect key.
* It is recommended that you register two or more PC cards in case you lose or
damage your registered PC card.
* Formatting your registered PC card will disable your protect key function.
NOTE:
For additional information contact your dealer or Digital Projection
Tools
Provides tools for setting On/Off timer, sleep timer, capturing im-
ages, displaying files or changing your background logo in a PC
Card and drawing.
Timer
Enables you to turn on or off your projector automatically at a
specified time. Two timer functions are available: On/Off Timer
and Sleep Timer.
NOTE: The projector has a built-in clock. The clock will keep working for about
three days after the main power is turned off. If the main power is not supplied to
the projector for three days or more, the built-in clock stops working.
On/Off Timer
6. Using On-Screen Menu
Up to 10 settings can be programmed.• Before setting On/Off Timer, make sure that Date, Time Preset feature
is set.
• Even after setting On/Off Timer, turning the projector on or off with the
remote control is possible.
Setting the On or Off Timer
1. Open the On/Off Timer window.
2. Select a program number (No. 1 to 10) by using the SELECT G or Hbutton.
3. Select “Edit” and press the ENTER button to open the Edit window.
4. Set the Day, Time (24 hours format), On-Time and Off-Time using the
SELECT buttons and the Software keyboard (1 thru 10). 
						

							E-72
5. Select On Timer or Off Timer
6. Repeat the Timer
To repeat the On Timer or Off Timer program every week, place a check
mark in “Repeat”.
7. Select “OK” and press the ENTER button on the remote control to com-
plete the setting. To cancel this and return to its previous screen, select
“Cancel”.
NOTE: If there is no operation for 4 hours or more after the projector is turned onwith On-Timer function, the projector will enter the standby or idle mode.
Enabling the On or Off Timer
1. To execute the setting, select “Active” .
2. Select “OK” and press the ENTER button.
NOTE: When one program or more are specified, all the settings are active.
NOTE: The settings will be executed in numerical order. Finished settings will beautomatically deleted.
NOTE: The On/Off Timer will not work while the cooling fans are running or an errormessage appears. Do not turn off the main power switch in this condition.
Disabling the On or Off Timer
To disable the setting, select “Inactive”. Select “OK” and press
the ENTER button.
6. Using On-Screen Menu
Deleting the On or Off Timer settings1. Select the setting you want to delete.
2. Select “Delete” and press the ENTER button.
3. Select “OK” and press the ENTER button to complete the deletion.
4. Select “Delete” again and press the ENTER button to return to the pre-
vious screen.
Enabling Sleep Timer
1. Select your desired time between 30 minutes and 16 hours: Off, 0:30,
1:00, 2:00, 4:00, 8:00, 12:00, 16:00.
2. Select “Set” and press the ENTER button on the remote control.
3. The remaining time starts counting down.
4. The projector will turn off after the countdown is complete.
NOTE:
• To cancel the preset time, set Off for the preset time or turn off the power.
• When the remaining time reaches 3 minutes before the projector is turned off,
the Projector will turn off in 3 minutes message will be displayed on the bottom
of the screen.
PC Card Files 
						

							E-73
The PC Card Files feature allows you to display a list of all the
files stored in the PC card so that you can select a file you want
to display. You can also sort files by file name or date, or display
the file. See page E-28.
Changing Background Logo:
You can change the default background logo using the PC Card
Files feature. See page E-28.
NOTE: File size must be 256KB or less. Other file formats than JPEG and BMP arenot available. See page E-28.
Help
Contents
Provides an online help about how to use the menus. An under-
lined link means that you can move to an adjustment item di-
rectly.
Selecting the underlined link and pressing ENTER button moves
to the corresponding adjustment item.
NOTE: The Help menu may not be displayed correctly when an image is overscanned.Source Information
Information
Displays the status of the current signal. This dialog box has
two pages.
Page 1
Source Name, Input Terminal, Entry No., Horizontal Frequency,
Vertical Frequency, Sync Polarity
Page 2 
						

							E-74
Signal Type, Video Type, Sync Type, Interlace, Direct Key
Projector Information
Displays the information for your Projector such as Remaining
Lamp Time, Lamp Hour Meter, Projector Usage, Projector ID,
version number and others. This dialog box has five pages.
Page 1
Remaining Lamp Time, Lamp Hour Meter, Projector Usage, Pro-
jector ID
NOTE: Nothing is displayed on the item, “Serial Number”. Please confirm the serialnumber on label attached on the projector itself.
Page 2
Version (BIOS/Firmware/Data/FPGA)
Page 3
Version (Formatter Red)
(Boot App / Config / Degamma / Main App / Sequences)
Page 4
Version (Formatter Green)
(Boot App / Config / Degamma / Main App / Sequences)
Page 5
Version (Formatter Blue)
(Boot App / Config / Degamma / Main App / Sequences)
Test Pattern
Press to display the test pattern. Pressing this button sequen-
tially selects 17 test patterns for each red, green and blue. 
						

							E-75 
						

							E-76
7
Maintenance
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
1 Cleaning the Cabinet and the Lens ....................... E-77 
						

							E-77
1. Turn off the Projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong detergents or solvents such as alcohol
or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mark the lens.
1 Cleaning the Cabinet and the Lens
7. Maintenance 
						

							E-78
8
Appendix
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
1 Troubleshooting ..................................................... E-79
2 Specifications ........................................................ E-81
3 Cabinet Dimensions .............................................. E-86
4 Compatible Input Signal List .................................. E-88
5 
Pin Assignment of PC CONTROL IN Connector (D-Sub 9 Pin)...... E90
6 
Pin Assignment of REMOTE IN 3 Connector (XLR connector)..... E-90
7 
Pin Assignment of EXT. I/O Connector (Mini D-Sub 15 Pin).... E-90
8 Using Software Keyboard ...................................... E-91
9 Operation Using an HTTP Browser ....................... E-91
INDEX ........................................................................ E-93 
						

							E-79
8. Appendix
1 Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Power Indicator
Indicator Condition
Projector Condition Note
Off
Blinking light
Steady lightGreen blinking
Orange blinking0.5 sec ON,
0.5 sec OFF
2.5 sec ON,
0.5 sec OFF
0.5 sec ON,
0.5 sec OFF
2.5 sec ON,
0.5 sec OFFThe main power is off
The projector is getting ready to turn on.
The lens shutter is closed.
Off Timer or Sleep Timer is active.
The projector is cooling down.
On Timer is active.
The projector is turned on.
The projector is in Standby. Green
Orange–
Wait for a moment.
–
Wait for a moment.
–
–
–
Indicator Condition
Projector Condition Note
Off
Blinking light
Steady lightRed blinking
Red
Orange
Green1 cycle (0.5 sec ON,
2.5 sec OFF)
2 cycle (0.5 sec ON,
0.5 sec OFF)
3 cycle (0.5 sec ON,
0.5 sec OFF)
4 cycle (0.5 sec ON,
0.5 sec OFF)
6 cycle (0.5 sec ON,
0.5 sec OFF)Normal
Lens hood or lamp cover error
Temperature error
Power error
Fan error
Lamp error
Circuit error
Control key locked
Idle condition–
Replace the lens hood or the lamp cover
correctly.
The projector is overheated. Move the
projector to a cooler location.
Power unit will not work correctly.
Cooling fan has stopped. Contact your
dealer.
Lamp fails to light. Wait 3 minutes and
then turn on again.
An error occurs in the circuit. Consult
your dealer.
You have pressed control panel key when
Control Key Lock is enabled.
–
Status Indicator
Error No.
Error Messages Description
Please ask your delivery outlets to handle the error codes.
0001
0002
0003
0004Cover Open
Lamp Data
Lamp Time Over
FPGA JOE2P
FPGA JOE2S
FPGA DVIOUT
FPGA WARPSEL
FPGA WARP
FPGA DVI1
FPGA DVI2
FPGA DVI3
FPGA DVI4
FPGA SDI1
FPGA SDI2
FPGA SDI3
FPGA SDI4
FPGA SLOTSEL
FPGA OSDCover open or TIMER
PWB contact failure
Malfunction on lamp data
Lamp time over (power-off)
FPGA configuration error
Error No.
Error Messages Description
0005
0006
0007
0008
0009
0010
0011
0012
0013
0014
0015Set Temp.
Fan Stop
Lamp PS Temp.
Lamp Temp.
Lamp Off
DMD Status
DMD Temp.
Lamp Fan Stop
Pump Stop
Power Supply
Lamp Time WarnTemprature malfunction
in internal set
Fan stop
Temprature malfunction
on Lamp PS
Temprature malfunction
on Lamp
No lamp lighting
DMD malfunction
DMD temprature malfunc-
tion
Lamp fan stop
Pump stop malfunction
Power supply mulfunction
Lamp time over (warning) 
						

							E-80
8. Appendix
Does not turn on
Will turn off
No picture
Image isn’t square to the
screen
Picture is blurred
Image is scrolling verti-
cally, horizontally or
both
Remote control does
not work
Indicator is lit or blink-
ing
Cross color in RGB
mode
USB mouse does not
work
No on-screen menu• Check that the power cable is plugged in and that the main power switch on the projector is on. See pages E-
28 and E-31.
• Ensure that the lamp cover is installed correctly.
• Check to see if the projector has overheated or the lamp has reached the end of its usable life. If there is
insufficient ventilation around the projector or if the room where you’re presenting is particularly warm, move
the projector to a cooler location.
• The lamp may fail to light. Wait a full minute and then turn on the power again.
• The lamp has reached the end of its usable life. Replace the lamp.
• Ensure that the off Timer is off. See page E-71.
• Use the menu or Source/Input button to select your source. See page E-32 or E-51.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. See page E-52.
• Select correct option in the Signal Select for current signal. See page E-62.
• Select RGB/Component when connecting DVD player to RGB connector of the projector. See page E-62.
• Apply a standard RGB signal when using RGB connector.
• Adjust picture for RGB signal.
• Make sure each setting is correct.
• If the problem still persists, reset the settings or adjustments to factory preset levels using the Factory Default
in the Adjustment Menu. See page E-60.
• If Security is enabled, a keyword or PC card as a protect key is required.
• Remove the lens cap.
• When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning
on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook
PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver
or power management software.
• Reposition the projector to improve its angle to the screen. See page E-32.
• Use the 3DReform function to correct the trapezoid distortion. See page E-56.
• Adjust the focus. See page E-33.
• Reposition the projector to improve its angle to the screen. See page E-32.
• Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page
E-23.
• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
• Use the menus or Source/Input button on the remote control or the cabinet to select the source you want to
input. See page E-32 or E-51.
• Install new batteries. See page E-19.
• Make sure there are no obstacles between you and the projector. See page E-19.
• Stand within 22 feet (7 m) of the projector. See page E-19.
• If the remote control cable plug is inserted into the REMOTE 1 IN jack, the remote control does not function
wirelessly. See page E-20.
• Make sure that the remote control’s ID corresponds with the projector’s ID. See page E-63.
• See the Power/Status Indicator on page E-79.
• If Auto Adjust is off, turn it on or adjust the image manually with the Position/Clock in the Image Options. See
page E-54.
• Make sure that your USB mouse is properly connected to the projector.
The projector may not support some brands of a USB mouse.
• Press MUTE OSD if the image is muted. Or press and hold CTL and press MUTE OSD button. See page E-37.
Problem Check These Items
Common Problems & Solutions