Digital Projection Highlite 14000hd Users Manual

							E-41
5. Setting Up for Double Stacking in Link Mode
13-1. Select “Projector Options” → “Setup” → “Page4” → “Pro-
jector ID” and assign an ID number to each projector. See also
page 8-18.
1-3-2. Select the same communication speed for both the pro-
jector.
NOTE: Do not turn on [Master] or [Slave] at this time.
 2  1
S-VIDEO
S-VIDEO
OUTPUT INPUT
AUDIO OUT VIDEO OUTLRS-VIDEOVIDEO
S-Video cable
(not supplied)
S-VIDEO
S-VIDEO
Signal Divider
Picture Device
Master projector
Slave projector
According to signal dividers, the port 
name, location and aspect are different. 
Please check the signal dividers 
instruction manuals.
According to picture devices, the port 
name, location and aspect are different.
Please check the picture devices 
instruction manuals.
S-Video cable (not supplied)
1-3-3. On the remote control specify the ID number of the pro-
jector to be adjusted. Press and hold the CTL and press
MENU (ADDRESS) button to enter the ID number.
You can operate the projector assigned the same ID number
as the remote control.
NOTE: Specifying None for projector ID allows you to operate multiple projectors
concurrently. However, some projectors may not synchronize to the other projec-
tors.
1-4. Stacking the Projectors
Place the projectors at the proper height for best screen to pro-
jector relationship. Make sure that all projectors have the same
display orientation.
1-5. Cable Connection
Example on Video Signal
Picture signal is divided by commercial signal divider, and connected to both master projector’s and slave projector’s input ports. 
						

							E-42
5. Setting Up for Double Stacking in Link Mode
1-6. Control Cable ConnectionExample of Remote Controllers Control
Remote controller and master projector’s remote controller input 1 port (REMOTE1 IN 1 )are connected by remote cable. Master
projector’s remote output port (REMOTE OUT) and slave projector’s remote controller input 1 port (REMOTE IN 1) are connected by
remote cable.
NOTE:
•When ID is not setup for the projector and remote controller, two projectors are controlled at the same time with one remote controllers. To control two projectors
indivisually, setup IDs for each projector and each remote controller.
NOTE:
• For HIGHlite14000HD, connect a ferrite core to the remote cable, at the end nearest the projector.  For how to install see page E-24.
Master projector
Slave projectorREMOTE
OUTREMOTE
IN 1
Remote control
REMOTE
IN 1
Ferrite clamp core(supplied)
Remote cable(supplied)
Remote cable
(supplied)
PC CONTROL 
IN
PC CONTROL 
IN
RS-232C Cross cable
(not supplied)
PC
or
Controller
Master projector
Slave projector
Example of RS-232C Control
The controller with RS-232C interface and each projector’s PC control-in port (PC CONTROL IN) are connected by cross cable and
the individuals are controlled by serial-control-command.
Please ask delivery outlets for serial-control-command. 
						

							E-43
5. Setting Up for Double Stacking in Link Mode
2 Adjusting and Registering Signals to Be
Projected
2-1. Making Adjustments to the Master Projector
2-1-1. Display a desired input signal on the master projector.
2-1-2. Make adjustment to the signal, then save (register) ad-
justments on the master projector by pressing and holding
CTL and pressing ENTRY LIST button on the remote con-
trol.
2-1-3. Repeat steps 2-1-1 and 2-1-2 for all signals you want
to project.
Display all the signals you registered and check. To check,
select “Source Select” → “Entry List”.
2-2. Making Adjustments to the Slave Projector
2-2-1. Display a desired input signal on the slave projector.
2-2-2. Make adjustment to the signal, then save (register) ad-
justments on the slave projector by pressing and holding
CTL and pressing ENTRY LIST button on the remote con-
trol.
2-2-3. Repeat steps 2-1-2 and 2-1-2 for all signals you want
to project.
Display all the signals you registered and check. To check,
select “Source Select” → “Entry List”.
3 Adjusting the Lens Shift, Zoom and Fo-
cus to Clearly Display all projected patterns
3-1. Display the internal crosshatch test pattern.
NOTE: Use a different single colour for each projector. Example: Turn on Green ofmaster projctor, then Red of the slave projector.
3-2. Adjust the Lens Shift by pressing and holding CTL and press-
ing the POSITION button on the remote control.
For lens shift adjustable range, see page E-23. Lens Shift Ad-
justable Range.
3-3. Zoom the lens in and out by pressing and holding CTL and
pressing the MAGNIFY(ZOOM)+/- button on the remote con-
trol.
3-4. Adjust the lens focus by pressing and holding CTL and press-
ing the FOCUS +/- button on the remote control.
NOTE: If the physical (vertical) alignment of the projector is not correct, adjust the
height of the feet. If there is any keystone distortion, use 3D-Reform (Keystone)
adjustment to correct and save the settings on each projector. See page E-55 for
3D-Reform. 
						

							E-44
6
Using On-Screen Menu
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
1 Basic Menu Operation ............................. E-44
2 List of Direct Button Combinations .......... E-46
3 Using the USB Mouse ............................. E-46
4 Menu Tree ................................................ E-47
5 Menu Descriptions & Functions ............... E-51
Source Select .......................................... E-51
Adjust (Source) ....................................... E-52
Picture ................................................ E-52
Video Adjust ....................................... E-52
Colour Management .......................... E-53
Gamma Correction ............................. E-53
Image Options .................................... E-54
Option Adjust ..................................... E-55
Lens Memory ..................................... E-55
Signal Type ......................................... E-56
Ref. Adjust ............................................... E-56
3D Reform .......................................... E-56
Screen ................................................ E-57
Ref. Lens Memory .............................. E-57Edge Blending .................................... E-58
Lamp Mode ........................................ E-60
Factory Default ........................................ E-60
Projector Options .................................... E-61
Menu .................................................. E-61
Setup .................................................. E-62
LAN Mode .......................................... E-64
Image Mode ....................................... E-67
Setting a Password ............................ E-69
Security .............................................. E-69
Tools ........................................................ E-71
Timer .................................................. E-71
PC Card Files ..................................... E-73
Help ......................................................... E-73
Contents ............................................. E-73
Source Information ............................. E-73
Projector Information .......................... E-74
Test Pattern ............................................. E-74 
						

							E-45
ENTER
ENTER
ENTER
MENU/ADDRESS
1 Basic Menu Operation
Using the Menus
1. Press the MENU button on the remote control or the Projector cabinet
to display the Basic, Advanced or Custom Menu.
Customizing the Menu
The Custom menu can be customized to meet your requirements.
Selecting a menu item from the Custom Menu Edit list, allows
you to custom tailor the menu items to your needs.
1. Select Custom Menu Edit to display the Custom Menu Edit screen.
2. Use the SELECT 
G or H buttons to highlight your selection and press
the ENTER button to place a check mark next to an option.
This action enables that feature. Press the ENTER button again to clear
the check box.
If you select an item with a solid triangle 
E and press the ENTER but-
ton on the remote control or the Switcher cabinet, you can enable all
the items within that submenu. Also you can turn on an item within the
submenu without placing a check mark on the main menu item.
NOTE: Up to 12 main menu items (within Custom Menu Edit, not includingsubmenu items) can be selected.
3. In order for the changes to take effect, use the SELECT 
F or E button
on the remote control or the Switcher cabinet to highlight OK, then
press the ENTER button. To cancel the changes, use the SELECT 
Gor H buttons to highlight Cancel and press the ENTER button.
To return to the factory default, select Reset then press the ENTER
button.
NOTE: Once you have selected OK on the Custom Menu Edit screen, you cannot
cancel the changes on the Menu screen. However, you can reedit the menu items
over again as described in the steps above.
NOTE: If the Advanced Menu item has been selected on the Menu mode, you get
the Change Custom menu now? upon completion of Custom Menu editing. In
this case, selecting Yes then ENTER will close all the menus and apply the changes
from the Advanced menu to the Custom Menu. If you select No then ENTER
functions, then all menu items will return to the Advanced menu, but your changes
will still be available within the Custom Menu selection. To display the previously
tailored Custom Menu, select Custom Menu from the Menu Mode.
An item To Advanced Menu will be added to the bottom of the
Custom Menu.
Selecting this item and pressing the ENTER button will display
the Advanced Menu features.
6. Using On-Screen Menu
2. Press the SELECT GH buttons on the remote control or the Projector
cabinet to highlight the menu for the item you want to adjust or set.
3. Press the SELECT E button or the ENTER button on the remote con-
trol or the Projector cabinet to select a submenu or item.
4. Adjust the level or turn the selected item on or off by using SELECT For E buttons on the remote control or the Projector cabinet.
The on-screen slide bar will show you the amount of increase or de-
crease.
5. Changes are stored until you adjust it again.
ENTER ........ Stores the setting or adjustments.
CANCEL ......Return to the previous screen without storing set-
tings or adjustments.
6. Repeat steps 2-5 to adjust an additional item, or press the CANCEL
button on the Projector cabinet or the remote control to quit the menu
display.
ENTERCANCEL 
						

							E-46
2 List of Direct Button Combinations
CTL+  Input  (1-10) Switches to any selected signal found in the Entry List.
To enable this combination, you must first assign specific remote buttons
for direct input selection in the Entry Edit window.
CTL+  ENTER (While  displaying  Entry  list) Displays the selected signal.
CTL+  CANCEL Returns  to  the previous menu without closing the slidebar or dialog.
CTL+  UNDO Clears all menus or adjustment/setting screens. All adjustments are saved
automatically.
CTL+ GHFEMoves  the slidebar or dialog box horizontally or vertically.
CTL+ F (BS) Deletes  one  letter  or numeral in the entry screen.
CTL+ MUTE OSD Turns off the on-screen display forcibly.
CTL+ MENU (ADDRESS) Displays the remote ID entry window.
CTL+ IMAGE (PROJECTOR) Sequentially selects the Projector Options sub menu.
CTL+  KEYSTONE This button has no function with the Projector.
CTL+  AMPLITUDE Service personnel only.
CTL+ ENTRY LIST Stores a signal in the Entry List.
6. Using On-Screen Menu
3 Using the USB Mouse
Using a commercially available USB mouse gives you smooth
operation.
NOTE: There may be some brands of USB mouse that the projector does not sup-port.
Operate the Menus using the USB mouse
Mouse Cursor
When connecting a USB mouse to the projector, you get a
mouse cursor on the screen.
Unless you use your USB mouse within 10 seconds, the mouse
cursor disappears.
Menu Display
Clicking with a mouse button displays the menu.
Clicking E displays the pull-down menu. To close the menu,
click anywhere in the background.
Adjusting and Setting Display
You can select a menu item and click with a mouse button to
make adjustments and setting.
Examples
Click (or press and hold) the mouse button F or E to adjust
the brightness. Or click and drag the mouse button on the slide
bar horizontally to adjust it.
To save the adjustments, click 
. This closes the menu. If
you click anywhere in the background while displaying an ad-
justment and setting menu or dialog box, you will go to the
main menu after clicking with the mouse.
Clicking 
 displays help.
USB A
Projector 
						

							E-47
4 Menu Tree
6. Using On-Screen Menu
NOTE: The shaded item indicates the default setting.
S1: Video
S1: S-Video
S1: Component
S2: RGB
S3: None
S4: None
Entry List
Load / Store / Cut / Copy / Paste / Edit / All Delete
Picture
Video Adjust
Colour Management
Gamma Correction
Image Options
Option Adjust
Lens Memory
Signal Type
Brightness / Contrast / Saturation / Colour / Hue /Sharpness /Setup Level
Noise Reduction Off / Low / Medium / High
Colour Matrix Select Colour Matrix HDTV / SDTV
Select Colour Matrix Type B-Y/R-Y / U/V / Cb/Cr /
Pb/Pr / IVX
Y/C Delay -15 to 15
YTR Adjustment 0 to 31
CTR Adjustment 0 to 31
Contrast Enhancement0 to 63
Telecine Auto / 2:2 Off / Off
3D Y/C Separation Off / On
Vertical Detail
Colour CorrectionRed / Green / Blue / Yellow / Magenta / Cyan / Colour Gain
Colour Temperature Low ←→ High
White Balance Brightness R / Brightness G / Brightness B /
Contrast R / Contrast G / Contrast B
Return to Reference Ok / Cancel
Set Custom / Set Reference / Cancel
Graphics Enhanced / Graphics / NTSC / NTSC Enhanced / PAL /
SECAM2.8 / PAL / SECAM Enhanced / Gamma1.0-3.0
Pixel Adjust Clock / Phase
Position Horizontal / Vertical
Aspect Ratio 1.25:1(5:4) / 1.33:1(4:3) / 1.78:1(16:9) / 1.85:1 /
2.35:1
Resolution Auto / Native
Overscan 0% / 5% / 8% / 10%
Synchronize Off / On / Adjust
Video Filter Off / Less / More
Blanking On / Off / Top / Bottom / Left / Right
Input Resolution Horizontal / Vertical
Input Position Horizontal / Vertical
Output Position Horizontal / Vertical
Clamp Timing Mode 0-4 / Adjust
Sync Protection Upper / Lower
VD Delay Adjustment / Field Invert (On/Off)
Signal Level Red / Green / Blue
Set Custom Point / Use Custom Point
RGB / Component
Advanced Menu
Source Select
Adjust (Source)
Ref. Adjust
Factory Default
Projector Options
Tools
Help
Test Pattern
* When the interface boards are installed at the factory. 
						

							E-48
6. Using On-Screen Menu
NOTE: The shaded item indicates the default setting.
3D Reform
Screen
Ref. Lens Memory
Edge Blending
Lamp Mode
All Data (Including Entry List) / Current Signal
Menu
Setup
Page 1
Page 2
Page 3
Page 1
Page 2
Page 3
Page 4
Advanced Menu
Source Select
Adjust (Source)
Ref. Adjust
Factory Default
Projector Options
Tools
Help
Test PatternCornerstone 8 direction / close
Keystone decrease ¨Æ increase
(When MM-WARP (optional) is inserted, horizontal / vertical)
Screen Type1.25:1(5:4) / 1.33:1(4:3) / 1.78:1(16:9) / 1.85:1 / 2.35:1
Position -64 to 64
Set Reference Point / Use Reference Point / Return to Factory Default
On / Off
▲/▼//Exit
Gamma Black Level (0-255)
Signal Adjust Black Level only (Off/On)
Input Resolution (Horizontal / Vertical)
Input Position (Horizontal / Vertical)
Adjust 65%~100% / Auto Off / On
LanguageEnglish / Deutsch / Français / Italiano / Español / Svenska / 
Menu Mode Basic / Custom Menu / Advanced Menu / Service Menu
Custom Menu Edit
Menu Display Time Manual / Auto 5 sec / Auto 15 sec / Auto 45 sec
Date Format MM/DD/YYYY / MM/DD/YYYY ddd / DD/MM/YYYY /
DD/MM/YYYY ddd / YYYY/MM/DD / YYYY/MM/DD ddd /
Month DD, YYYY / Month DD, YYYY ddd
Date, Time Preset Date (MM/DD/YYYY (ddd) ) / Time (HH:MM)
Display SelectDate / Time / Input Terminal / Source Name / Projector ID / Message
Menu Colour Colour / Monochrome
OrientationDesktop Front / Ceiling Rear / Desktop Rear / Ceiling Front
Background Blue / Black / Logo
Sync Termination  (RGB)Hi-Z / 75 [Ω]
Signal Select RGB (RGB/Component / RGB / Component)
Video (Auto/NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL60/SECAM)
S-Video (Auto/NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL60/SECAM)
Auto Adjust On / Off
Auto Start On / Off
Power Off ConfirmationOn / Off
WARP Correction On / Off (When optional MM-WARP is used, it can choose.)
Last Memory On / Off
Lens shutter on duringOn / Off
signal switching
Communication Speed4800 / 9600 / 19200 / 38400
Projector ID Enable (1 to 64) / Disable
Default Source SelectLast / Auto / Select
Select: Slot1-1(Video) / Slot1-2(S-Video) /
Slot1-3(Component) / Slot2-1(RGB) /
Slot3-1(None) / Slot4-1(None)
* When the interface boards are installed at the factory.
Control Panel Key LockEnable / Disable 
						

							E-49
6. Using On-Screen Menu
NOTE: The shaded item indicates the default setting.
Advanced Menu
Source Select
Adjust (Source)
Ref. Adjust
Factory Default
Projector Options
Tools
Help
Test PatternLAN Mode
Image Mode
Password
Security
Status
Mail
Timer
PC Card Files
On / Off Timer Active / Inactive / Edit / Delete
Sleep Timer Remaining Time / Preset Time
Execute / Exit / Logo
Projector Name
IP Address
Subnet Mask
Gateway
MAC Address
Advanced IP Address Automatic / Manual
IP Address
Subnet Mask
Gateway
DNS Configuration
Domain Name
Network TypeModeInfrastructure /
802.11 Ad Hoc
SSID
Channel Auto, 1 to 13
TX Rate
Automatic / 54M /
48M / 36M / 24M/
18M / 12M / 9M/
6M / 11M / 5.5M /
2M / 1M
WEP WEPDisable / 64 bit /
128 bit / 152bit
Key Select Key 1 to 4
Key 1 to 4
DHCP
Host Name option None / Request /
Discover/Request
Host Name
Client-Identifer optionNone / Request /
Discover/Request
Use Mac AddressOn / Off
Client-Identifer
Recconect
Alert Mail On/Off
Sender’s Address
SMTP Server Name
Recipient’s Adderss 1 to 3
Test Mail
Seamless / 2 Images / Off
Effect None / Wipe Down / Wipe Left /
Wipe Up / Wipe Right / Box In /
Box Out / Alpha Blending
Speed Fast / Medium / Slow
Mode Side by Side / Picture in Picture
Menu Entry / Delete
Logo Entry / Delete
Enable / Disable
Keyword
Use Protect key / Read / Register / Delete 
						

							E-50
6. Using On-Screen Menu
Contents
Source Information
Projector Information
Page 1 Source Name / Input Terminal / Entry No. /
Horizontal Frequency / Vertical Frequency / Sync Polarity
Page 2 Signal Type / Video Type / Sync Type / Interlace / Direct Key
Page 1 Serial Number / Remaining Lamp Time / Lamp Hour Meter /
Projector Usage / Projector ID
Page 2 Version (BIOS / Firmware / Data / FPGA)
Page 3 Version (Formatter Red)
(Boot App / Config / Degamma / Main App / Sequences)
Page 4 Version (Formatter Green)
(Boot App / Config / Degamma / Main App / Sequences)
Page 5 Version (Formatter Blue)
(Boot App / Config / Degamma / Main App / Sequences)
Cross Hatch / Cross Hatch(Inv) / Alignment / Alignment(Inv) / Horizontal Gray Scale / Horizontal Gray Scale(Inv) /
Vertical Gray Scale / Vertical Gray Scale(Inv) / Horizontal RAMP / Horizontal RAMP(Inv) / Vertical RAMP /
Vertical RAMP(Inv) / Raster(0%) / Raster(25%) / Raster(50%) / Raster(75%) / Raster(100%)
Red On / Off
Green On / Off
Blue On / Off
Advanced Menu
Source Select
Adjust (Source)
Ref. Adjust
Factory Default
Projector Options
Tools
Help
Test Pattern