Digital Projection E-Vision 8000 Series User Guides

							Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_6
...continued from previous page
Notes
LAMPS menu
lamps= ?0 = Single
1 = Dual
Not applicable when lamp is cooling.
lamp.mode= ?0 = Economy
1 = Standard
2 = Dimming
Drive
Not applicable without signal locked.
lamp.pwr= ?0 ~ 25 ( 80.4 % ~ 100.0 % )Not applicable without signal locked.
altitude= ?0 = Off
1 = On
High Altitude
lamp1.stat?0 = Off
1 = On
lamp2.stat?0 = Off
1 = On
ALIGNMENT menu
proj.mode= ?0 = Front
1 = Rear
2 = Ceiling + Front
3 = Ceiling + Rear
fan.pos= ?0 = Normal
1 = Vertical
2 = Down
zoomio+ -+ = Zoom out
- = Zoom in
focus+ -+ = Focus Near
- = Focus Far
vert.offset+ -+ = Up
- = Down
Vertical Lens Shift
horiz.offset+ -+ = Right
- = Left
Horizontal Lens Shift
lens.load=1 ~ 10Lens Memory Load
lens.save=1 ~ 10Lens Memory Save
lens.center(execute)
continued on next page...
Notes 
Rev B September 2012  
						

							Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_7
...continued from previous page
Notes
h.keystone= ? + --350 ~ +350The sum of the absolute values of h.keystone and 
v.keystone cannot be greater than 350.
v.keystone= ? + --200 ~ +200The sum of the absolute values of h.keystone and 
v.keystone cannot be greater than 350.
warp.rotat= ? + --20 ~ +20Each unit is ¼°. 
warp.pinbrl= ? + --100 ~ +100Pincushion/Barrel
warp.tlc.x
warp.tlc.y
= ? + -x: -192 ~ +192
y: -120 ~ +120
Top Left Corner
warp.trc.x
warp.trc.y
= ? + -x: -192 ~ +192
y: -120 ~ +120
Top Right Corner
warp.blc.x
warp.blc.y
= ? + -x: -192 ~ +192
y: -120 ~ +120
Bottom Left Corner
warp.brc.x
warp.brc.y
= ? + -x: -192 ~ +192
y: -120 ~ +120
Bottom Right Corner
warp.reset(execute)
blank.top= ? + -0 ~ 360
blank.btm= ? + -0 ~ 360
blank.left= ? + -0 ~ 534
blank.right= ? + -0 ~ 534
blank.rst(execute)
eb.stat= ?0 = Off
1 = On
Edge Blend
eb.wht.top= ? + -0, 200 ~ 500Blend Width Top
1-199 not allowed
eb.wht.btm= ? + -0, 200 ~ 500Blend Width Bottom
1-199 not allowed
eb.wht.left= ? + -0, 200 ~ 800Blend Width Left
1-199 not allowed
eb.wht.right= ? + -0, 200 ~ 800Blend Width Right
1-199 not allowed
eb.blk.top= ? + -0, 8, 16, 24, 32Black Level Uplift Area Top
continued on next page...
Notes 
Rev B September 2012  
						

							Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_8
...continued from previous page
Notes
eb.blk.btm= ? + -0, 8, 16, 24, 32Black Level Uplift Area Bottom
eb.blk.left= ? + -0, 4, 8, 12, 16, 20, 24, 28, 32Black Level Uplift Area Left
eb.blk.right= ? + -0, 4, 8, 12, 16, 20, 24, 28, 32Black Level Uplift Area Right
eb.all= ? + -0 ~ 32Black Level Uplift Adjust Width All
eb.red= ? + -0 ~ 32Black Level Uplift Adjust Width Red
eb.green= ? + -0 ~ 32Black Level Uplift Adjust Width Green
eb.blue= ? + -0 ~ 32Black Level Uplift Adjust Width Blue
eb.reset(execute)
eb.adl= ?0 = Off
1 = On
Align Pattern
CONTROL menu
eco.net.pow= ?0 = Off (ECO Standby Mode)
1 = On (Standard Standby Mode)
Eco Network Power
auto.powoff= ?0 = Off 
1 = On
auto.powon= ?0 = Off 
1 = On
proj.ctrl= ?0 = RS232
1 = network
Not applicable when Eco Network Power is on.
net.ipaddr= ?
net.subnet= ?
net.gateway= ?
net.dhcp= ?0 = Off
1 = On
startup.logo= ?0 = Off
1 = On
continued on next page...
Notes 
Rev B September 2012  
						

							Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_9
...continued from previous page
Notes
trig.1= ?0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = Letterbox
7 = Native
8 = Unscaled
9  = Auto
If trig.1 is set to Auto, the projector will start 
sending the trigger as soon as it is switched on. 
Otherwise the trigger will be sent only when the 
aspect ratio matches this setting.
auto.src= ?0 = Off 
1 = On
Auto Search
dblack= ?0 = Off
1 = On
Dynamic Black
lang= ?0 = English
1 = French
2 = Spanish
3 = German
4 = Portuguese
5 = Chinese Simplified
6 = Chinese Traditional
7 = Japanese
8 = Korean
SERVICE menu
model?
ser.no?
sw.ver?
act.src?0 = HDMI
1 = DVI
2 = VGA
3 = Component / BNC
4 = Composite
5 = S-Video
6 = 3G-SDI
Active Source
continued on next page...
Notes 
Rev B September 2012  
						

							Digital Projection E-Vision 8000 series  THE OPERATION COMMANDS Remote Communications Guide
Page Rem_10
...continued from previous page
Notes
pip.src?0 = HDMI
1 = DVI
2 = VGA
3 = Component / BNC
4 = Composite
5 = S-Video
6 = 3G-SDI
PIP Source
pixel.clock?In MHz
Not applicable without signal locked.
signal?Not applicable without signal locked.
h.refresh?Not applicable without signal locked.
v.refresh?Not applicable without signal locked.
lamp1.hours?
lamp2.hours?
proj.runtime?
blue.only= ?0 = Off
1 = On
fact.reset(execute)Factory reset
Miscellaneous commands
power.on(execute)Power on
power.off(execute)Power off (puts projector into Standby mode)
picture.mute= ?0 = Off
1 = On
status?0 = standby 
1 = warm up 
2 = imaging 
3 = cooling 
4 = warning
remote.set= ?1 ~ 10: Set Projector ID
255: Clear Projector ID (No ID)
Notes 
Rev B September 2012  
						

							Digital Projection E-Vision 8000 series  THE KEY COMMANDS Remote Communications Guide
Page Rem_11
The Key Commands
Corresponding remote control key
power.onPOWER ON
power.offPOWER OFF
menuMENU
exitEXIT
inputINPUT
picturePICTURE
networkNETWORK
autosyncAUTO SYNC
aspectASPECT
pipPIP
overscanOVERSCAN
freezeFREEZE
lampmodeLAMP MODE
infoINFO
shutterSHUTTER
idsetID SET
lensshiftLENS SHIFT
testpatternTEST PATTERN
enterENTER
upUP
downDOWN
leftLEFT
rightRIGHT
Notes
 An input command will return 
“NA” when the input command is 
not applicable in some specific 
conditions. 
Rev B September 2012  
						

							Digital Projection E-Vision 8000 series  WEB CONFIGURATION UTILITY Remote Communications Guide
Page Rem_12
Web Configuration Utility
The LAN IP Address of the projector can be set remotely using the Web Configuration Utility.
• Make sure the projector is connected to a remote computer via LAN.
• From the remote computer, access the default LAN IP address of the projector. The Web Configuration Utility opens.
It is possible to control many of the projector’s settings using the embedded Web Configuration Utility. The following pages contain a few 
examples of such settings.
Examples
Navigate to the Control tab and edit the settings as required.
The Source/general page enables you to:
• switch the projector on and off
• open and close the shutter
• select an input source
Notes
 Eco Network Power must be set to 
Standard, if you wish to control the 
projector via the LAN connection.
 The default LAN IP address is 
192.168.0.100
  If you suspect this has been 
changed, then you can view the 
current Network settings in the 
Control Menu.
 For more information about 
connecting the projector via LAN, 
see the Connection Guide. 
Rev B September 2012  
						

							Digital Projection E-Vision 8000 series  WEB CONFIGURATION UTILITY Remote Communications Guide
Page Rem_13
Examples - continued from previous page
The Image settings page allows access to settings from the 
Picture menu.
The Lens adjustments page allows access to lens control 
settings. 
Notes 
Rev B September 2012  
						

							Digital Projection E-Vision 8000 series  WEB CONFIGURATION UTILITY Remote Communications Guide
Page Rem_14
Examples - continued from previous page
The Geometry adjust and Edge Blend pages allow access to 
settings from the Alignment menu.
Notes 
Rev B September 2012  
						

							Digital Projection E-Vision 8000 series  WEB CONFIGURATION UTILITY Remote Communications Guide
Page Rem_15
Examples - continued from previous page
The Advanced control page allows access to settings 
from the Picture menu, Color sub-menu.
To view and edit your network settings, navigate to 
the Configuration tab.
Notes 
Rev B September 2012