Digital Projection E-Vision 6000 Series User Guides

							Digital Projection E-Vision 6000 Series SUPPORTED SIGNAL INPUT MODES Connection Guide
Conn 3
...continued from previous page
SignalResolutionRefresh Rate ( Hz )
Total number of lines
Horizontal  Frequency (kHz)
VIDEO /S-VIDEOCOMPONENTCOMPUTER 1
(VGA)
COMPUTER 2(RGB/YCrCb)COMPUTER 3
(DVI-D)
COMPUTERWXGA601366 x 76859.879947.8üüü
continuedWXGA+601440 x 90059.993355.9üüü
SXGA751152 x 8647590067.5üüü
SXGA601280 x 96060100060üüü
SXGA601280 x 102460106764üüü
SXGA751280 x 102475106780üüü
SXGA+601400 x 105060108865.3üüü
WSXGA+1680 x 105060108865.3üüü
UXGA601600 x 120060125075.00üüü
MACMAC13640 x 48066.652635.0üüü
MAC16832 x 62474.566749.7üüü
MAC191024 x 76874.980460.2üüü
MAC211152 x 87075.191568.7üüü
Notes 
Rev A September 2012  
						

							Digital Projection E-Vision 6000 Series CONTROL CONNECTIONS Connection Guide
Conn 4
Control Connections
Screen Trigger
•	The Trigger output can be connected to an electrically operated screen, 
automatically deploying the screen when the projector is switched on, an\
d 
retracting the screen when the projector is switched to standby.
USB
•	The USB port is used to download firmware updates, issued from time to 
time by Digital Projection.
Serial Port
•	The projector’s features can be controlled via a serial connection, using the 
control strings described in the Remote Communications Guide.
LAN ()
•	The projector’s features can be controlled via a LAN connection, using 
the industry standard PJLink commands. The PJLink specification can be 
downloaded from 
http://pjlink.jbmia.or.jp/english - click on the Specifications link.
•	The LAN IP Address of the projector can be set by using the Network 
submenu, which can be found in the Advanced Setting submenu in the 
Installation menu.
•	Once the LAN IP Address has been set, it is possible to assign a Host 
Name and Domain Name to the projector, and to set up an Alert Mail 
address and PJLink password.
•	A number of basic picture and input settings can be controlled directly u\
sing 
the embedded LAN Control utility.
LENS SHIFTZOOM–FOCUS+
MENU
ENTER RETURN
SOURCE
POWER WARNING
LAMP1LAMP2AUT
O
Notes
 For a complete listing of pin 
configurations for all signal and 
control connectors, see Wiring 
Details later in this Guide.
 Only one remote connection can 
be used at any one time. For more 
information, see the Installation 
menu in the Operating Guide.
 When Standby Mode is set to 
Power-saving, the LAN connection 
is disabled.
 For more information about 
PJLink settings, see the Remote 
Communications Guide.
 For full details of how to use the 
LAN Control Utility, see the 
Remote Communications Guide.
Connection Panel 
Rev A September 2012  
						

							Digital Projection E-Vision 6000 Series WIRING DETAILS Connection Guide
Conn 5
Wiring Details
Signal inputs and outputs
Computer 1
Video input: analog computer (VGA)
15 way D-type connector
1 R
2 G
3 B
4 unused 
5 Digital Ground (H Sync)
6 R Ground
7 B Ground
8 G Ground
9 +5v
10 Digital Ground (V Sync/DDC)
11 unused
12 SDA
13 H Sync
14 V Sync
15 SCL
Audio input
3.5mm mini jack
Tip Left
Ring Right
Sleeve Ground
Notes
 For full details of all input settings, 
see the Setting menu in the 
Operating Guide.
Computer 1 video: 
pin view of female connector
Sleeve
Ring
Tip
Computer 1 audio 
Rev A September 2012  
						

							Digital Projection E-Vision 6000 Series WIRING DETAILS Connection Guide
Conn 6
Computer 2
Video input: RGBHV, RGsB or YCrCb
5 x 75 ohm BNC
RGBHV  RGsB   YCrCb
Green    Green + Sync     Y
Blue   Blue   Cb
Red   Red   Cr
Hsync
Vsync
Audio input
3.5mm mini jack
Tip Left
Ring Right
Sleeve Ground
Notes
 For full details of all input settings, 
see the Setting menu in the 
Operating Guide.
R/Cr           G/Y         B/Cb            H            V
Computer 2 video
Sleeve
Ring
Tip
Computer 2 audio 
Rev A September 2012  
						

							Digital Projection E-Vision 6000 Series WIRING DETAILS Connection Guide
Conn 7
Computer 3
Video input: DVI-D
24 way D-type connector
1 TMDS Data 2-
2 TMDS Data 2+
3 TMDS Data 2 Shield
4 unused
5 unused
6 DDC Clock
7 DDC Data
8 unused
9 TMDS Data 1-
10 TMDS Data 1+
11 TMDS Data 1 Shield
12 unused
13 unused
14 +5 V Power
15 Ground
16 Hot Plug Detect*
17 TMDS Data 0-
18 TMDS Data 0+
19 TMDS Data 0 Shield
20 unused
21 unused
22 TMDS Clock Shield
23 TMDS Clock+
24 TMDS Clock-
Audio input
3.5mm mini jack
Tip Left
Ring Right
Sleeve Ground
Computer 3 video: 
pin view of female connector
Notes
 High Definition Content Protection 
(HDCP) is supported on this input.
 For full details of all input settings, 
see the Setting menu in the 
Operating Guide.
Sleeve
Ring
Tip
Computer 3 audio 
Rev A September 2012  
						

							Digital Projection E-Vision 6000 Series WIRING DETAILS Connection Guide
Conn 8
Component
Video input
3 x RCA Phono
YCrCb  YPrPb
Cr  Pr
Y  Y
Cb  Pb
Audio
2 x RCA Phono
Left or Mono audio
Right audio
L           R
    Y      Pb/Cb     Pr/Cr
Notes
 For full details of all input settings, 
see the Setting menu in the 
Operating Guide.
Component audio
Component video 
Rev A September 2012  
						

							Digital Projection E-Vision 6000 Series WIRING DETAILS Connection Guide
Conn 9
Video and S-Video
Video input
1 x RCA Phono
Composite Video
S-Video input
4 pin mini-DIN
1 Y Ground
2 C Ground
3 Luminance (Y)
4 Chrominance (C)
Shared audio input for Video and S-Video
2 x RCA Phono
Left or Mono audio
Right audio
S-Video: 
pin view of female connector
L           R
Notes
 For full details of all input settings, 
see the Advanced menu in the 
Operating Guide.
Video
Video and S-Video: shared audio input 
Rev A September 2012  
						

							Digital Projection E-Vision 6000 Series WIRING DETAILS Connection Guide
Conn 10
Notes
 Monitor Out only displays the input 
from Computer 1.
 For full details of all input settings, 
see the Advanced menu in the 
Operating Guide.
Monitor Out
Video output: analog computer (VGA)
15 way D-type connector
1 R
2 G
3 B
4 unused 
5  Digital Ground (H Sync)
6 R Ground
7 B Ground
8 G Ground
9 +5v
10 Digital Ground (V Sync/DDC)
11 unused
12 SDA
13 H Sync
14 V Sync
15 SCL
Audio output
3.5mm mini jack
Tip Left
Ring Right
Sleeve Ground
Monitor Out video: 
pin view of female connector
Sleeve
Ring
Tip
Monitor Out audio 
Rev A September 2012  
						

							Digital Projection E-Vision 6000 Series WIRING DETAILS Connection Guide
Conn 11
Control connections
Screen Trigger output
3.5mm mini jack
Tip Signal
Sleeve Ground
Serial Port
9 way D-type connector
1 unused
2 Received Data (RX)
3 Transmitted Data (TX)
4 unused
5 Signal Ground
6 unused
7 unused
8 unused
9 unused
LAN connection ()
RJ45 socket
Serial Port: 
pin view of female connector
Notes
 Only one remote connection can 
be used at any one time. For more 
information, see the Installation 
menu in the Operating Guide.
 For information about how to set 
the LAN IP configuration, see the 
Operating Guide.
SleeveTip
Screen Trigger
LAN connection 
Rev A September 2012  
						

							This page is intentionally left blank.