DiBoss Lt 32hlfh Instruction Manual

							TFT / LCD TV 
ENGLISH
Instruction Manual
LT-26HLFH/32HLFH
 
						

							Warnings
WARNING : To prevent fire or shock hazard, do not expose the set to rain or moisture. Do not rub
or strike the Active Matrix LCD with anything hard as this may scratch, mar, or
damage the Active Matrix LCD permanently.
CAUTION:Unauthorised tampering with the inside of the TV invalidates the warranty.
The manufacturer shall not warrant for any damage caused by improper maintenance
and repair work by third parties.
Power(LT-26HLFH) Use only the AC-DC adaptor supplied with the set and never apply an AC mains to
the set directly. The AC-DC adaptor operates on an AC mains supply, the voltage is
as indicated on the label of the AC-DC adaptor.
a. Connect the DC plug of the AC-DC adaptor to the 24V socket of the set.
b. Connect the AC-DC adaptor and its power cord.
c. Connect the power cord to an AC mains.
In the event of thunderstorms or power cuts, please pull out the mains plug of the
AC-DC adaptor and the aerial plug. Do not allow anything to rest upon or roll over the
power cord, and do not place the set where the power cord is subject to damage.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING :The unit is operated at dangerous voltages. The unit may only be opened by an
authorised specialist. All maintenance and servicing work must be carried out by
an authorised company. Repairs that are carried out incorrectly could result in
fatal injuries to the user.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
2
 
						

							ENGLISH
223
ServiceNever remove the back cover of the TV, this can expose you to high voltage and
other hazards. If the TV does not operate properly, unplug it and call your dealer.
Connect the antenna cable to the connection marked Ant. (on the rear). For best
reception, use an outdoor antenna.
LocationPosition your TV so that no bright light or sunlight will shine directly on the screen. Do
not expose the TV to vibration, moisture, dust or heat. Also ensure that the TV is
placed in a position that allows a free flow of air. Do not cover the ventilation
openings on the back cover. You can install the TV on a wall or place it on a table-top
or similar flat surface. Mounted the TV securely to eliminate the risk of injury from the
TV falling.
CleaningUnplug the TV before cleaning the face of the LCD Screen. Dust the TV by wiping the
screen and cabinet with a soft, clean cloth. If the screen requires additional cleaning,
use a clean, damp cloth. Do not use liquid or aerosol cleaners.
Warnings
 
						

							Warnings2~3
Contents4
Supplied Accessories5
Installation6
Controls7~9
Controller of panel  7
Remote controller  8~9
Basic Operation 10
Turning the TV On and Off   10
Programme selection    10
Volume adjustment  10
Q.View   10
Sound mute function    10
On screen Language selection    10
On Screen Menus and Displays 11
Setting up TV Programme 12~15
Auto Programme    12
Manual Programme   13
Programme Edit  14
Picture Control 15
Manual picture control   15
Auto picture control  15
Sound Control 16~17
Other functions 18~19
Clock  18
Blue Back   18
Auto Sleep  19
Childlock 19
Radio 19
ARC 19
Radio Control20
Other functions21
Teletext22~23
Text On/Off   22
TOP text   22
FLOF text   22
Special Teletext function   23
External Equipment Connection24~25
Antenna connection   24
SCART 1,2   24
HDMI IN   24
S-VIDEO Input  25
Headphone jack   25
Digital Audio OUTPUT 25
COMPONENT INPUT 25
Connecting the PC(HDMI/VGA) as a monitor26~29
Product specification30 Before operating the set, please read this manual carefully.
Contents
4
 
						

							ENGLISH
5
Supplied Accessories
LMake Sure the following accessories are provided with Product.
1. AC/DC adaptor(LT-26HLFH)
3. Remote controller
5. Instruction manual 6. VGA cable 
7. PC Audio IN cable 4. Batteries (type AAA) 2. AC Cord
Model:LT
-26HLFH/32HLFH
Owner’s Manual
26 /32 WIDE LCD TV/MONITOR
 
						

							6
Installation
Installation Options* You can install the TV on a wall or place it on a table-like surface.
* To eliminate any risk of injury from the TV falling, it should be mounted securely.
1. Wall InstallationCaution: Do not install the TV on a
weak wall surface, like plaster etc. 
When the TV is placed into a cupboard
the distance between the TV and the
wall have to leave minimum 60mm
square as below.
When the TV is mounted on the wall.,
the distance between the TV and the
wall have to leave minimum 30mm
square as below.
For detailed information, refer to the wall mount bracket instruction (not included in
delivery) supplied with wall mount bracket.
2. Desktop InstallationInstalling Stand
1. Lay down the TV as pictured below. 
Please ensure that the table/box has a protection sheet to avoid any scratch or 
damage to the TV screen.. Please ensure that there is no pressure directly applied 
to the front surface of the TV screen when laying the 
product down on its face. 
2. Locate the stand on its mounting position and use 
the 8 supplied screws to attach the stand to the TV. 
Ensure that all of them are securely tightened.
3. The TV and stand may now be placed upright, ready 
for viewing.
 
						

							ENGLISH
227
Controls
1. DC IN(LT-26HLFH)
2. HDMI (High Definition Multimedia Interface) IN
Connect to the HDMI jack for device with HDMI output.
3. H/P (Headphone out)Connect a headphone to this socket.
4. PC AUDIO IN
Connect the audio cable from the PC to the PC AUDIO INof the set.
5. SVC portConnector for service only.
6. PC ANALOG IN (D-SUB)
7. S-VIDEO IN
Connect the output of the S -VIDEO on the VCR to the S-VIDEO input.
Connect the audio outputs of the S-VIDEO on the VCR to the Audio IN (L(MONO), R).
8. COAX OUT Connect to a Digital Audio component.
9. COMPONENT IN
Connect component video/audio from a DVD/Set-top box.
10. SCART1
Connect the Audio/Video outputs of external equipment to scart jack.
11. SCART2
12. Ant. (Antenna input)  1. ON/OFFSwitches TV set on or off.
2. MENU
Displays a menu.
3. + PR -(Programme Up/Down)
Selects a programme or a menu item.
4. + VOL -(Volume Up/Down)
Adjusts the volume./ Adjusts menu settings.
5. TV/AV Selects TV, SCART1,SCART2, S-VIDEO, RADIO(Only when the set isRadio On.), COMPONENT, PC ANALOG, HDMI mode. / Clears the menu from the screen.6. Power Indicator 
Illuminates in red when the TV is in standby mode./ Illuminates in green when the 
TV is switched on.
7. Remote control sensor 
Accepts the IR signal of remote controller.
76
1
2
5 3
4
1✽23 54
6789 10 1112
 
						

							228
Controls
All the functions can be controlled with the remote controller. Some functions can
also be adjusted with the buttons on the side panel of the set.  
Remote controllerBefore you use the remote controller, please install the batteries.  
1. POWERTurns the TV on from standby or off to standby mode.
2. MUTETurns the sound on and off.
3. NUMBER buttonsSelects programme numbers.
4. TV/AVSelects TV, SCART1,SCART2, S-VIDEO, 
RADIO(Only when the set is Radio On.), 
COMPONENT, PC ANALOG, HDMI mode.
Clears the menu from the screen.
5. MENUDisplays a main menu.
6. LISTDisplays the programme list menu.
7. I/IISelects the language during dual language broadcast.
Selects the sound output.
8. SLEEPSets the sleep timer.
9. PÏ
PReturns to the previously viewed programme.
10. PRx/PRy(Programme Up/Down)Selects next programme or a menu item.  
11. OKAccepts your selection or displays the current mode.
12. VOLÏ/VOLq(Volume Up/Down)Adjusts the sound level.
13. TV/PCSelects TV or PC mode directly.
 
						

							ENGLISH
229
Controls
→→
Battery installation
uInserting batteries
1. Remove the battery cover by pulling it 
upward in the direction shown by the arrow.2. Insert the batteries with correct polarity 
3. Replace the battery compartment cover.
-Install two high-quality 1.5V AAA alkaline batteries. Dont mix old batteries with   
new batteries.
- Remove batteries when you wont use the remote controller for a long time. Liquid     
leakage from old batteries may cause operation failure.
uNotes for using remote controller
• Make sure there are no objects between the remote controller and its sensor.
• Dont place the remote control near a heater or in damp place. Strong impact to the
remote control may cause operation failure.
• Signal from the remote control may be disturbed by sun light or other bright light. In
this case, darken the room or move the TV. 
14. PICTURE(    )Recalls your preferred picture setting
15. SOUND(    )Recalls your preferred sound setting
16. ARC(    )You can watch TV in various picture formats; Auto,
16:9, 14:9, 4:3, 16:9 Zoom, 14:9 Zoom, 4:3 Zoom.
Repeatedly press the ARCbutton to select your 
desired picture format.
Note.16:9 and 4:3 in PC mode are available.
17. TELETEXT buttons These buttons are used for Teletext.
For further details, see the ‘Teletext’ section.
18. INPUT(    )Selects the AV source of sub picture in PIP mode.
19. PIP(    )Displays a PIP(Picture In Picture) screen.
20. POSITION(    )Selects a position of PIP screen.
21. SWAP(    )Switches a main picture to sub picture in PIP mode.
22. MODE(    )Selects a PIP screen mode. – 16:1, 9:1 and 3:1 mode.
23. PIP PRx/PIP PRySelects a programme when RF signal is displayed in
PIP mode.
24. ÏqAdjusts menu settings.
 
						

							2210
Turning the TV On and OffStandby Setup: The AC-DC adapter and the AC power cord
must be set up and connected to have the TV in standby mode
ready to be turned on. Press the ON/OFFbutton on the side
panel of the TV to go into standby mode.
1. If the TV is in standby mode, press the POWERbutton
on the remote controller or the TV itself to turn the TV on.
2. Press the Power button again on the remote controller or
the ON/OFFbutton the TV itself to turn the TV off.
Note: If the TV is on and the POWERbutton is pressed to turn
the TV off, the TV goes into standby mode.
Programme selectionYou can select a Programme number with the PRx/PRy
button or NUMBER buttons.
Volume adjustmentPress the  VOLÏ/VOLqbutton to adjust the sound level.
Last programmePress thePÏPbutton to view the last Programme you were
watching.
Sound mute function
Press the MUTE() button. The sound is switched off and the
mute  display appears.
To cancel mute mode, press the MUTE()button again,
VOLÏ/VOLqorSOUND(    ) button.
On screen menu language selectionThe menu can be displayed on the screen in desired 
language. First, select your language.
1. Press the MENUbutton.
2. Select the Setupmenu.
3. Press the Ïqbutton to select the Setup menu.
4. Select the Languagemenu.
5. Press the Ïqbutton to select the language.
6. Press the PRx/PRybutton to select your desired
language. 
7. Press the TV/AVbutton.
All the on screen displays will appear in the selected
language.
Basic Operation