Dell U2711 Users Guide

   
Universal Serial Bus (USB) Interface  Width   646.71 mm (25.46 inches)
Depth   199.95 mm (7.87 inches)
Dimensions (without stand)  
Height  
385.67 mm (15.18 inches) 
Width   646.71 mm (25.46 inches)
Depth   93 mm (3.66 inches)
Stand Dimensions     
Height (Compressed)   354.5 mm (13.96 inches)
Height (Extended)   394 mm (15.51 inches)
Width   320 mm (12.60 inches)
Depth   199.95 mm (7.87 inches)
   
Weight with packaging   14.46 kg (31.88 lb)
Weight with stand assembly and 
cables   10.46 kg (23.06...

USB Upstream Connector  
   
  
USB Downstream Connector  
   
  
USB Ports  
l 1 upstream  -  rear   
l 4 downstream  -  2 on rear; 2 on left  side  
Card Reader Specifications  
Overview  
l The Flash Memory Card Reader is a USB storage device that allows users to read and write information from and into the memory card.   
    
l The Flash Memory Card Reader is automatically recognized by Microsoft ®  Windows ®  2000, Windows ®  XP, Windows Vista ®  and Widows ®  7.   
    
l Once installed and...

    
l USB - IF certification   
    
l Supports various memory card media   
 
 
   
The following table lists the memory cards supported:  
Maximum Card Capacity Supported by the U2711 card reader  
   
General   
Performance    
Plug and Play Capability  
You can install the monitor in any Plug and Play - compatible system. The monitor automatically provides the computer system with its Extended Display 
Identification Data (EDID) using Display Data Channel (DDC) protocols so the system can configure...

Fo r best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:  
l To clean your antistatic screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen - cleaning tissue or solution suitable for the 
antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.   
l Use a lightly - dampened, warm cloth to clean the plastics. Avoid using detergent of any kind as some detergents leave a milky...

Back to Contents Page    
 
Appendix  
 
   Safety Instructions  
   FCC Notice (U.S. Only) and Other Regulatory Information  
   Contacting Dell  
   
CAUTION: Safety Instructions  
For information on safety instructions, see the  Safety Information .  
FCC Notice (U.S. Only) and Other Regulatory Information  
For FCC notices and other regulatory information, see the regulatory compliance website located at  www.dell.com
egulatory_compliance .  
Contacting Dell  
      To contact Dell electronically,...

Back to Contents Page    
 
Setting Up Your Monitor   
 
 
1. Go to  http://support.dell.com ,  enter your service tag, and download the latest driver for your graphics card.  
2. After installing the drivers for your Graphics Adapter, attempt to set the resolution to   2048x1152/2560x1440  again.  
   
Back to Contents Page  NOTE:  If you are unable to set the resolution to 2048x1152/2560x1440 ,  please contact Dell™ to inquire about a Graphics Adapter that supports these 
resolutions.    

Back to Contents Page    
Setting Up Your Monitor   
 
 
In Windows XP:  
1. Right - click on the desktop and click  Properties .  
2. Select the  Settings  tab.  
3. Select  Advanced .  
4. Identify your graphics controller supplier from the description at the top of the window (e.g. NVIDIA, ATI, Intel etc.).   
5. Please refer to the graphics card provider website for updated driver (for example,  http://www.ATI.com  OR  http://www.NVIDIA.com  ).  
6. After installing the drivers for your Graphics...

Back to Contents Page    
Operating the Monitor   
 
   Using the Front Panel Controls  
   Using the On - Scree Display (OSD) Menu  
   Setting the Maximum Resolution  
   Using the Dell Soundbar (Optional)  
   Using the Tilt, Swivel and Vertical Extension  
   
Using the Front Panel  
Use the buttons on the front of the monitor to adjust the image settings.   
NOTE:  1~5 are capacitive touch sensor keys, which are activated by placing your finger on the blue LED.    
      
1 - 3 Shortcut keys   Use...

     
If either VGA or DVI - D input is selected and both VGA and DVI - D cables are not connected, a floating dialog box as shown below appears. 
    
If either Composite, or Component input is selected and the cables are not connected or the video source is turned off, the screen does 
not have an image. If any button is touched (except power button), the monitor displays the following message:  
     or
or  
4
 
OSD Menu   Use this key to open the on - screen display (OSD). See  Using the OSD Menu ....

   
Using the OSD Menu  
1. Touch   to launch the OSD menu and display the main menu.   
Main Menu for Analog (VGA) Input  
 
Or  
Main Menu for non Analog (non VGA) Input  NOTE:  If you change the settings and then either proceed to another menu, or exit the OSD menu, the monitor 
automatically saves the changes. The changes are also saved if you change the settings and then wait for the 
OSD menu to disappear.