Dell M4700 Manual

4.Work your way around the sides and top edge of the display bezel and remove the display bezel from the computer .
Installing the Display Bezel
1.Slide in the display bezel from the bottom and press on the display bezel.
51 

2.Work around the entire bezel until it snaps onto the display assembly.
3.Install the battery.
4.Follow the procedures in After Working Inside Your Computer.
Removing the Display Panel
1.Follow the procedures in Before Working Inside Your Computer.
2.Remove the:
a.battery
b.display bezel
3.Remove the screw that secures the display panel to the display assembly. Flip the display panel over.
52 

4.Peel back the adhesive tape that secures the LVDS cable to the display panel.
5.Disconnect the LVDS cable.
53 

6.Remove the screws that secure the display brackets to the display panel. Remove the display brackets.
7.
54 

Installing the Display Panel
1.Align the display brackets to the display panel.
2.Tighten the screws to secure the display brackets to the display panel.
3.Connect the LVDS cable and affix the adhesive tape.
4.Align the display panel in its original position on the computer.
5.Tighten the screws to secure the display panel to the display assembly.
6.Install the:
a.display bezel
b.battery
7.Follow the procedures in After Working Inside Your Computer.
Removing the Camera
1.Follow the procedures in Before...

3
System Setup
System Setup enables you to manage your computer hardware and specify BIOS‐level options. From the System Setup, 
you can:
•Change the NVRAM settings after you add or remove hardware
•View the system hardware configuration
•Enable or disable integrated devices
•Set performance and power management thresholds
•Manage your computer security
 
Boot Sequence
Boot Sequence allows you to bypass the System Setup ‐defined boot device order and boot directly to a specific device 
(for example:...

Table 1. Navigation KeysKeysNavigationUp arrowMoves to the previous field.Down arrowMoves to the next field.Allows you to select a value in the selected field (if applicable) or follow the link in the field.SpacebarExpands or collapses a drop‐down list, if applicable.Moves to the next focus area.
NOTE: For the standard graphics browser only.
Moves to the previous page till you view the main screen. Pressing  in the main screen 
displays a message that prompts you to save any unsaved changes and restarts...

Table 3. System ConfigurationOptionDescriptionIntegrated NICAllows you to configure the integrated 
network controller. The options are:
•Disabled
•Enabled
•Enabled w/PXE (Default Setting)
Parallel PortAllows you to define and set how the parallel 
port on the docking station operates. You can 
set the parallel port to:
•Disabled
•AT
•PS2
•ECP
Serial PortIdentifies and defines the serial port settings.  You can set the serial port to:
•Disabled
•COM1 (Default Setting)
•COM2
•COM3
•COM4
NOTE: The...

OptionDescriptionSMART ReportingThis field controls whether hard drive errors 
for integrated drives are reported during 
system startup. This technology is part of the 
SMART (Self Monitoring Analysis and 
Reporting Technology) specification.
•Enable SMART Reporting — This option is 
disabled by default.
USB ConfigurationAllows you to define the USB configuration. 
The options are:
•Enable Boot Support
•Enable External USB Port
Default Setting: both the options are enabled.
USB PowerShareAllows you to...

OptionDescriptionNOTE: You must set the admin password before you set the system or hard 
drive password.
NOTE: Successful password changes take effect immediately.
NOTE: Deleting the admin password automatically deletes the system 
password and the hard drive password.
NOTE: Successful password changes take effect immediately.
Default Setting: Not set
System PasswordAllows you to set, change or delete the system password.
NOTE: Successful password changes take effect immediately.
Default Setting: Not...