Dell M4700 Manual

2.Press on the positions indicated until it snaps in place.
3.Connect the following cables to the system board:
a.power button
b.touchpad
c.speaker
d.media board
e.fingerprint
f.RFID
4.Tighten the screws to secure the palmrest to the front of the computer.
5.Tighten the screws to secure the palmrest to the base of the computer.
6.Install the:
a.hard drive 
b.optical drive
c.keyboard
d.keyboard trim
e.base cover
f.battery
7.Follow the procedures in After Working Inside Your Computer.
Removing the...

c.base cover
d.keyboard trim
e.keyboard
f.optical drive
g.hard drive 
h.palm rest
3.Disconnect the :
a.ExpressCard cable from the system board
b.the USH board cable from the USH board (M4700 only)
4.Remove the screws that secure the ExpressCard module to the computer and remove the ExpressCard module.
Installing the ExpressCard Module
1.Insert the ExpressCard module into its compartment.
2.Tighten the screws to secure the ExpressCard module to the computer
3.Connect the:
a.ExpressCard cable to the system...

a.palm rest
b.hard drive 
c.optical drive
d.keyboard
e.keyboard trim
f.base cover
g.battery
h.ExpressCard
5.Follow the procedures in After Working Inside Your Computer.
Removing The Heat Sink
1.Follow the procedures in Before Working Inside Your Computer.
2.Remove the:
a.battery
b.base cover
c.keyboard trim
d.keyboard
e.optical drive
f.hard drive 
g.palm rest
h.processor fan
3.Loosen the captive screws that secure the heat sink to the computer. Lift up and remove the heat sink from the computer....

g.base cover
h.battery
3.Follow the procedures in After Working Inside Your Computer.
Removing the Processor
1.Follow the procedures in Before Working Inside Your Computer.
2.Remove the:
a.battery
b.base cover
c.keyboard trim
d.keyboard
e.optical drive
f.hard drive 
g.palm rest
h.processor fan
i.heat sink
3.Rotate the processor cam lock in a counter-clockwise direction. Remove the processor from the computer.
Installing the Processor
1.Align the notches on the processor and the socket, and insert the...

c.keyboard trim
d.keyboard
e.optical drive
f.hard drive
g.palm rest
h.video fan
3.Disconnect and un-route any antenna cables connected to installed wireless cards.
4.Remove the antenna cables from the routing channels.
5.Loosen the captive screws on the heat sink.
35 

6.Remove the video-card heat sink from the computer.
Installing the Video-Card Heat Sink
1.Slide the heat sink into its original position in the computer.
2.Tighten the captive screws to secure the heat sink.
3.Route and connect the antenna cables to the installed wireless cards.
4.Install the:
a.video fan
b.palm rest
c.hard drive
d.optical drive
e.keyboard
f.keyboard trim
36 

g.bottom door
h.battery
5.Follow the procedures in After Working Inside Your Computer.
Removing the Video Card
1.Follow the procedures in Before Working Inside Your Computer.
2.Remove the:
a.battery
b.base cover
c.keyboard trim
d.keyboard
e.optical drive
f.hard drive 
g.palm rest
h.video-card fan
i.video-card heat sink
j.heatsink
3.Remove the screws that secure the video card to the computer. Remove the video card from the computer.
Installing the Video Card
1.Insert the video card into its slot in the...

Removing the Input/Output (I/O) Board
1.Follow the procedures in Before Working Inside Your Computer.
2.Remove the:
a.SD card
b.battery
c.base cover
d.keyboard trim
e.keyboard
f.optical drive
g.hard drive 
h.palmrest
3.Disconnect the ExpressCard module connector from the I/O board.
4.Remove the screw that secures the I/O board to the computer. Lift the right edge of the I/O board upwards to disengage the connector and remove it from computer.
38 

Installing the I/O Board
1.Connect the I/O board connector and slide the I/O board into its slot in the computer.
2.Tighten the screw to secure the I/O board to the computer.
3.Connect the ExpressCard module connector to the I/O board.
4.Install the:
a.palmrest
b.hard drive 
c.optical drive
d.keyboard
e.keyboard trim
f.base cover
g.battery
h.SD card
5.Follow the procedures in After Working Inside Your Computer.
Removing the Switch Board
1.Follow the procedures in Before Working Inside Your Computer....

g.palmrest
3.Disconnect the switch-board cable from the system board and remove it from the latches. Remove the screws that secure the switch board to the computer and remove it from the computer.
Installing the Switch Board
1.Align the switch board to its original position on the computer.
2.Tighten the screws to secure the switch board to the computer.
3.Connect the switch-board cable to the system board and secure it through the routing channel.
4.Install the:
a.palmrest
b.hard drive 
c.optical drive...