dell latitude v710 v740 User Manual

Microprocessor Module: Dell Latitude V710/V740 Service Manual
 
1 screwdriver 
(perpendicular to 
microprocessor)
2 pin-1 corner
3 processor die (do not 
touch)
4 ZIF socket
5 ZIF-socket cam screw
1.  Remove the 
keyboard. 
2.  Remove the 
EMI Shield. 
file:///F|/Service%20Manuals/Dell/Latitude/v710-740/cpu.htm (2 of 4) [\
2/28/2004 8:22:17 AM] 

Microprocessor Module: Dell Latitude V710/V740 Service Manual
NOTICE: To ensure maximum cooling for the microprocessor, do not touch the 
heat transfer areas on the microprocessor thermal-cooling assembly. The \
oils in 
your skin reduce the heat transfer capability of the thermal pads. 
3.  Remove the 
microprocessor thermal-cooling assembly. 
NOTICE: When removing the microprocessor module, pull the module straight 
up. Be careful not to bend the pins on the microprocessor module. 
4.  To loosen the...

Microprocessor Module: Dell Latitude V710/V740 Service Manual
When the microprocessor module is correctly seated, all four corners are\
 aligned 
at the same height. If one or more corners of the module are higher than\
 the 
others, the module is not seated correctly.
NOTICE: Hold the microprocessor down while turning the cam screw to prevent 
intermittent contact between the cam screw and microprocessor. 
2.  Tighten the ZIF socket by turning the cam screw clockwise to secure the \
 microprocessor...

Flashing the BIOS: Dell Latitude V710/V740 Service Manual
Back to Contents Page 
Flashing the BIOS 
Dell™ Latitude™ V710/V740 Service Manual
1.  Ensure that the AC adapter is plugged in and that the main battery is in\
stalled properly. 
2.  Turn on the computer. 
Follow the instructions that appear on the screen. The computer continue\
s to boot 
and updates the new BIOS. When the flash update is complete, the compute\
r will 
automatically reboot. 
3.  Press 
 during POST to enter the system setup...

Speakers: Dell Latitude V710/V740 Service Manual
Back to Contents Page 
Speakers 
Dell™ Latitude™ V710/V740 Service Manual
Removing the Speakers 
NOTICE: Disconnect the computer and any attached devices from electrical 
outlets, and remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
touching an unpainted metal surface on the computer. 
NOTICE: Read Preparing to Work Inside the Computer before performing the 
following procedure. 
The speakers...

Speakers: Dell Latitude V710/V740 Service Manual
 
1 speaker connector 7hard drive cage
2 routing clips (10) 8left speaker cable
3 battery bay 9left die casting
4 right speaker 10left speaker
5 right speaker cable 11floppy drive cage
6 right die casting   
1.  Remove the 
hard drive. 
2.  Remove the 
floppy drive. 
3.  Remove the 
keyboard. 
4.  Remove the 
display assembly. 
5.  Remove the 
EMI Shield. 
6.  Remove the 
video board. 
file:///F|/Service%20Manuals/Dell/Latitude/v710-740/speakers.htm (2 of...

Speakers: Dell Latitude V710/V740 Service Manual
7.  Remove the palm rest. 
8.  Disconnect the speaker connector from the system board. 
NOTICE: Remove the speaker cables from their routing clips and die casting 
with care to avoid damaging the cables. 
9.  Remove the speaker cables from under or between their routing clips and \
die  casting. 
NOTICE: Handle the speakers with care to avoid damaging them. 
10.  Remove the speakers by pulling them straight up and out of the bottom ca\
se. 
 
1 left...

Speakers: Dell Latitude V710/V740 Service Manual
NOTE: The right speaker cable is longer than the left speaker cable. 
NOTE: Speakers face out in the bottom case holders. 
1.  Slide the speakers down into the bottom case. 
NOTICE: Ensure that the speaker cables are under or between their routing 
clips, and route the left and right speaker cables properly beneath the \
die 
casting. 
NOTICE: Route the speaker cables with care to avoid damaging them. 
2.  Route the speaker cables under or between their...

System Board: Dell Latitude V710/V740 Service Manual
Back to Contents Page 
System Board 
Dell™ Latitude™ V710/V740 Service Manual
Removing the System Board 
NOTICE: For V740 only, prior to replacing the system board, ensure that a thermal pad 
is present on the Memory Controller Hub (MCH) heat-sink, located on th\
e base plastics. If 
a thermal pad is already present, you do not need to replace it. 
The system boards BIOS chip contains the service tag sequence, which is\
 also visible on a 
barcode...

System Board: Dell Latitude V710/V740 Service Manual
10.  Remove the palm rest. 
11.  Remove the 
microprocessor thermal-cooling assembly. 
12.  Remove the 
microprocessor. 
13.  Remove the 
speakers. 
 
1 floppy drive cage
2 M2.5 x 5-mm screws (2)
3 hard drive cage
4 M2.5 x 5-mm screws (2)
14.  Remove the two M2.5 x 5-mm screws that secure the floppy drive cage to t\
he system  board, and lift the floppy drive cage out of the bottom case. 
15.  Remove the two M2.5 x 5-mm screws that secure the hard...