dell latitude v710 v740 User Manual

EMI Shield, Video Board, and Palm Rest: Dell Latitude V710/V740 Service \
Manual
 
1 bottom of V710 video 
board
2 video board connector
3 system board
4 interface connector
NOTICE: For V740 only, before you connect the video board to the system board, e\
nsure 
that you route the power- board flex cable under the memory module. 
V740 Video Board Connector 
file:///F|/Service%20Manuals/Dell/Latitude/v710-740/palmrest.htm (7 of \
12) [2/28/2004 8:22:16 AM] 

EMI Shield, Video Board, and Palm Rest: Dell Latitude V710/V740 Service \
Manual
 
1 bottom of V740 video 
board
2 video board connector
3 system board
4 interface connector
5 power-board flex cable
6 memory module
3.  Reinstall the screw that secures the video board to the bottom case: 
l     For V710, reinstall the M2.5 x 5-mm screw.
l     For V740, reinstall the M2.5 x 8-mm screw.
4.  Replace the 
EMI Shield. 
file:///F|/Service%20Manuals/Dell/Latitude/v710-740/palmrest.htm (8 of \
12) [2/28/2004...

EMI Shield, Video Board, and Palm Rest: Dell Latitude V710/V740 Service \
Manual
5.  Replace the keyboard. 
Palm Rest
NOTICE: Disconnect the computer and any attached devices from electrical outlets\
, and 
remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by tou\
ching 
an unpainted metal surface on the computer. 
NOTICE: Read Preparing to Work Inside the Computer before performing the following 
procedure. 
1.  Remove the 
keyboard. 
NOTICE: You...

EMI Shield, Video Board, and Palm Rest: Dell Latitude V710/V740 Service \
Manual
 
1 M2.5 x 5-mm screws (2)
2 top of the palm rest
6.  Turn the computer over and remove the twelve M2.5 x 8-mm screws labeled \
circle P. 
file:///F|/Service%20Manuals/Dell/Latitude/v710-740/palmrest.htm (10 of\
 12) [2/28/2004 8:22:16 AM] 

EMI Shield, Video Board, and Palm Rest: Dell Latitude V710/V740 Service \
Manual
 
1 M2.5 x 8-mm screws 
(12)
7.  Turn the computer over, and disconnect the touch pad connector and power\
 board  connector from the system board. 
file:///F|/Service%20Manuals/Dell/Latitude/v710-740/palmrest.htm (11 of\
 12) [2/28/2004 8:22:16 AM] 

EMI Shield, Video Board, and Palm Rest: Dell Latitude V710/V740 Service \
Manual
 
1 back center of the palm 
rest
2 touch pad connector
3 power board connector
NOTICE: Carefully separate the palm rest from the bottom case to avoid damage to\
 the 
palm rest. 
8.  Starting at the back center of the palm rest, use your fingers to separa\
te the palm rest  from the bottom case by lifting the inside of the palm rest while pushin\
g in on the 
outside. 
Back to Contents Page...

Microprocessor Thermal-Cooling Assembly: Dell Latitude V710/V740 Service\
 Manual
Back to Contents Page 
Microprocessor Thermal-Cooling 
Assembly 
Dell™ Latitude™ V710/V740 Service Manual
Removing the Microprocessor Thermal-Cooling 
Assembly 
NOTICE: Disconnect the computer and any attached devices from electrical 
outlets, and remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
touching an unpainted metal surface on the computer. 
NOTICE: Read...

Microprocessor Thermal-Cooling Assembly: Dell Latitude V710/V740 Service\
 Manual
 
1 microprocessor thermal-
cooling assembly
2 captive screws (4)
3 fan power cable
5.  Lift the microprocessor thermal-cooling assembly up toward the front of \
the  computer and out of the system board. 
Replacing the Microprocessor Thermal-Cooling 
Assembly 
1.  Place the back of the microprocessor thermal-cooling assembly under the \
palm rest and lower the assembly onto the system board. 
2.  Tighten the four captive...

Microprocessor Thermal-Cooling Assembly: Dell Latitude V710/V740 Service\
 Manual
 
 
 
file:///F|/Service%20Manuals/Dell/Latitude/v710-740/thermal.htm (3 of 3\
) [2/28/2004 8:22:16 AM] 

Microprocessor Module: Dell Latitude V710/V740 Service Manual
Back to Contents Page 
Microprocessor Module 
Dell™ Latitude™ V710/V740 Service Manual
Removing the Microprocessor Module 
NOTICE: Disconnect the computer and any attached devices from electrical 
outlets, and remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
touching an unpainted metal surface on the computer. 
NOTICE: Read Preparing to Work Inside the Computer before performing the...