dell latitude c610 c510 User Manual

							Palm Rest: Dell Latitude C610/C510 Service Manual
Back to Contents Page 
Palm Rest 
Dell™ Latitude™ C610/C510 Service Manual
  Removing the Palm Rest 
Removing the Palm Rest 
NOTICE: Disconnect the computer and any attached devices from electrical outlets\
, and 
remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by tou\
ching 
an unpainted metal surface on the computer. 
NOTICE: Read Preparing to Work Inside the Computer before performing the following 
procedure. 
1.  Remove the 
hard drive. 
2.  Remove the 
keyboard. 
NOTICE: You must remove the display assembly before you remove the palm rest; th\
e 
display hinges pass through the back of the palm rest. 
3.  Remove the 
display assembly and hinge covers. 
4.  Turn the computer over and remove the three M2.5 x 12-mm screws labeled \
circle P. 
Palm Rest Screw Removal 
file:///F|/Service%20Manuals/Dell/Latitude/c510-610/palmrest.htm (1 of \
4) [2/28/2004 7:55:50 AM] 
						

							Palm Rest: Dell Latitude C610/C510 Service Manual
 
1 M2.5 x 12-mm screws (3)
2 M2 x 3-mm screws (2)
3 hard-drive bay door
5.  Remove the two M2 x 3-mm screws that are located in the hard-drive bay d\
oor labeled  circle P. 
6.  Turn the computer over, and remove the three M2 x 3-mm screws that secur\
e the palm  rest to the bottom case. 
a.  Remove the two M2 x 3-mm screws that are located on the back edge of the\
  bottom case, underneath the display assembly. 
b.  Remove the M2 x 3-mm screw located underneath the keyboard, on the right\
 side  of the bottom case, next to the microprocessor thermal cooling assembly.\
 
7.  Pull up on the pull tab that is attached to the palm-rest flex cable con\
nector to remove it  from the interface connector on the system board. 
Palm Rest Removal 
file:///F|/Service%20Manuals/Dell/Latitude/c510-610/palmrest.htm (2 of \
4) [2/28/2004 7:55:50 AM] 
						

							Palm Rest: Dell Latitude C610/C510 Service Manual
 
1 M2 x 3-mm screws (3)
2 palm rest
3 palm-rest flex cable
4 bottom case
5 touch pad connector
6 back center of the palm rest
NOTICE: Carefully separate the palm rest from the bottom case to avoid damage to\
 the 
palm rest. 
8.  Starting at the back center of the palm rest, use your fingers to separa\
te the palm rest  from the bottom case by lifting up the inside of the palm rest while pus\
hing in on the 
outside. 
file:///F|/Service%20Manuals/Dell/Latitude/c510-610/palmrest.htm (3 of \
4) [2/28/2004 7:55:50 AM] 
						

							Palm Rest: Dell Latitude C610/C510 Service Manual
Back to Contents Page
 
 
 
file:///F|/Service%20Manuals/Dell/Latitude/c510-610/palmrest.htm (4 of \
4) [2/28/2004 7:55:50 AM] 
						

							Microprocessor Thermal Cooling Assembly: Dell Latitude C610/C510 Service\
 Manual
Back to Contents Page 
Microprocessor Thermal Cooling 
Assembly 
Dell™ Latitude™ C610/C510 Service Manual
  Removing the Microprocessor Thermal Cooling Assembly 
  Replacing the Microprocessor Thermal Cooling Assembly 
Removing the Microprocessor Thermal Cooling 
Assembly 
NOTICE: Disconnect the computer and any attached devices from electrical 
outlets, and remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
touching an unpainted metal surface on the computer. 
NOTICE: Read Preparing to Work Inside the Computer before performing the 
following procedure. 
1.  Remove the 
hard drive. 
2.  Remove the 
keyboard. 
3.  Loosen the four captive screws that secure the microprocessor thermal co\
oling  assembly to the system board. 
Microprocessor Thermal Cooling Assembly Removal 
file:///F|/Service%20Manuals/Dell/Latitude/c510-610/thermal.htm (1 of 3\
) [2/28/2004 7:55:51 AM] 
						

							Microprocessor Thermal Cooling Assembly: Dell Latitude C610/C510 Service\
 Manual
 
1 microprocessor thermal cooling assembly
2 captive screws (4)
3 right side
4.  Lift the microprocessor thermal cooling assembly up and out of the syste\
m  board. 
Replacing the Microprocessor Thermal Cooling 
Assembly 
1.  Place the right side of the microprocessor thermal cooling assembly unde\
r the 
file:///F|/Service%20Manuals/Dell/Latitude/c510-610/thermal.htm (2 of 3\
) [2/28/2004 7:55:51 AM] 
						

							Microprocessor Thermal Cooling Assembly: Dell Latitude C610/C510 Service\
 Manual
palm rest and lower the assembly onto the system board. 
2.  Tighten the four captive screws, labeled 1 through 4, in consecutive ord\
er. 
Back to Contents Page
 
 
 
file:///F|/Service%20Manuals/Dell/Latitude/c510-610/thermal.htm (3 of 3\
) [2/28/2004 7:55:51 AM] 
						

							Microprocessor Module: Dell Latitude C610/C510 Service Manual
Back to Contents Page 
Microprocessor Module 
Dell™ Latitude™ C610/C510 Service Manual
  Removing the Microprocessor Module 
  Replacing the Microprocessor Module 
Removing the Microprocessor Module 
NOTICE: Disconnect the computer and any attached devices from electrical 
outlets, and remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
touching an unpainted metal surface on the computer. 
NOTICE: Read Preparing to Work Inside the Computer before performing the 
following procedure. 
Microprocessor Module Removal 
NOTICE: Do not touch the processor die. Press and hold the microprocessor 
down on the substrate on which the die is mounted while turning the cam \
screw 
to prevent intermittent contact between the cam screw and microprocessor\
. 
NOTICE: To avoid damage to the microprocessor, hold the screwdriver so that 
it is perpendicular to the microprocessor when turning the cam screw. 
file:///F|/Service%20Manuals/Dell/Latitude/c510-610/cpu.htm (1 of 4) [\
2/28/2004 7:55:51 AM] 
						

							Microprocessor Module: Dell Latitude C610/C510 Service Manual
 
1 screwdriver (perpendicular to microprocessor)
2 pin-1 corner
3 processor die (do not touch)
4 ZIF socket
5 ZIF-socket cam screw
1.  Remove the 
hard drive. 
2.  Remove the 
keyboard. 
NOTICE: To ensure maximum cooling for the microprocessor, do not touch the 
heat transfer areas on the microprocessor thermal cooling assembly. The \
oils in 
your skin reduce the heat transfer capability of the thermal pads. 
3.  Remove the 
microprocessor thermal cooling assembly. 
file:///F|/Service%20Manuals/Dell/Latitude/c510-610/cpu.htm (2 of 4) [\
2/28/2004 7:55:51 AM] 
						

							Microprocessor Module: Dell Latitude C610/C510 Service Manual
NOTICE: When removing the microprocessor module, pull the module straight 
up. Be careful not to bend the pins on the microprocessor module. 
4.  To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate\
 the ZIF- socket cam screw counter-clockwise until it comes to the cam stop. 
The ZIF-socket cam screw secures the microprocessor to the system board.\
 Take 
note of the arrow on the ZIF-socket cam screw (see 
Microprocessor Module 
Removal).
5.  Use a microprocessor extraction tool to remove the microprocessor module\
. 
Replacing the Microprocessor Module 
NOTICE: Ensure that the cam lock is in the fully open position before seating 
the microprocessor module. Seating the microprocessor module properly in\
 the 
ZIF socket does not require force. 
NOTICE: A microprocessor module that is not properly seated can result in an 
intermittent connection, or permanent damage to the microprocessor and Z\
IF 
socket. 
1.  Align the pin-1 corner of the microprocessor module with the pin-1 corne\
r of the  ZIF socket, and insert the microprocessor module. 
NOTE: The pin-1 corner of the microprocessor module has a triangle that aligns\
 
with the triangle on the pin-1 corner of the ZIF socket. 
NOTICE: You must position the microprocessor module correctly in the ZIF 
socket to avoid permanent damage to the module and the socket. 
When the microprocessor module is correctly seated, all four corners are\
 aligned 
at the same height. If one or more corners of the module are higher than\
 the 
others, the module is not seated correctly.
file:///F|/Service%20Manuals/Dell/Latitude/c510-610/cpu.htm (3 of 4) [\
2/28/2004 7:55:51 AM]