dell inspiron 8200 User Manual

Palm Rest: Dell Inspiron 8200
Back to Contents Page 
Palm Rest 
Dell™ Inspiron™ 8200
NOTICE: Disconnect the computer and attached devices from electrical outlets 
and remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
periodically touching unpainted metal on the computer. 
 
1 pull loop
file:///F|/Service%20Manuals/Dell/Inspiron/8200/palmrest.htm (1 of 4) \
[2/28/2004 7:40:55 AM] 

Palm Rest: Dell Inspiron 8200
NOTICE: The reserve battery provides power to the computers time RTC and 
NVRAM when the computer is turned off. Removing the palm rest disconnect\
s 
the reserve battery and causes the computer to lose the date and time 
information as well as all user-specified parameters in NVRAM. If possib\
le, copy 
the information before you disconnect the reserve battery. 
Removing the Palm Rest 
1.  Follow the instructions in Preparing to Work Inside the Computer. 
2.  Remove the...

Palm Rest: Dell Inspiron 8200
 
1 M2.5 x 20-mm screws 
(9)
8.  Turn the computer over. 
9.  Use the pull loop to disconnect the palm-rest flex cable from the touch-\
pad  connector on the system board. 
10.  On the left and right sides of the palm rest, use a flat-blade scribe be\
tween the  palm rest and the bottom case of the computer to separate the snaps that\
 
secure the palm rest to the bottom case. 
11.  Lift out the palm rest. 
file:///F|/Service%20Manuals/Dell/Inspiron/8200/palmrest.htm (3 of...

Palm Rest: Dell Inspiron 8200
Replacing the Palm Rest 
When replacing the palm rest screws, install the two screws at the back \
corners of the 
computer first to help align the palm rest correctly.
Back to Contents Page
 
 
 
file:///F|/Service%20Manuals/Dell/Inspiron/8200/palmrest.htm (4 of 4) \
[2/28/2004 7:40:55 AM] 

Reserve Battery: Dell Inspiron 8200
Back to Contents Page 
Reserve Battery 
Dell™ Inspiron™ 8200
NOTICE: Disconnect the computer and attached devices from electrical outlets 
and remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
periodically touching unpainted metal on the computer. 
 
1 palm rest bracket
2 reserve battery
3 reserve battery cable
file:///F|/Service%20Manuals/Dell/Inspiron/8200/resbatt.htm (1 of 3) [\
2/28/2004 7:40:56 AM] 

Reserve Battery: Dell Inspiron 8200
NOTICE: The reserve battery provides power to the computers RTC and 
NVRAM when the computer is turned off. Removing the battery causes the 
computer to lose the date and time information as well as all user-speci\
fied 
parameters in NVRAM. If possible, copy the information before you remove\
 the 
reserve battery. 
Removing the Reserve Battery 
1.  Follow the instructions in Preparing to Work Inside the Computer. 
2.  Remove the 
keyboard. 
3.  Remove the 
hinge...

Reserve Battery: Dell Inspiron 8200
1M2.5 x 4-mm screws (4)
2 palm rest bracket
3 palm-rest flex cable
7.  Remove the four M2.5 x 4-mm screws that secure the palm rest bracket. 
8.  While supporting the palm-rest flex cable, lift out the palm rest bracke\
t and turn  it over. 
9.  Disconnect the reserve battery cable. 
10.  Remove the reserve battery:  a.  Pry the reserve battery free from the metal palm rest bracket. 
b.  Remove the foam-pad remnants from the palm rest bracket. 
Replacing the Reserve...

System Board: Dell Inspiron 8200
Back to Contents Page 
System Board 
Dell™ Inspiron™ 8200
NOTICE: Disconnect the computer and attached devices from electrical outlets 
and remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
periodically touching unpainted metal on the computer. 
 
1 M2.5 x 4-mm captive-
washer screws (3)
file:///F|/Service%20Manuals/Dell/Inspiron/8200/sysboard.htm (1 of 5) \
[2/28/2004 7:40:57 AM] 

System Board: Dell Inspiron 8200
2system board
3 network connector
4 modem connector
5 network cable cover
6 M2.5 x 20-mm screw
The BIOS chip on the system board contains the service tag sequence, whi\
ch is also 
visible on a bar code label on the bottom of the computer.
The replacement kit for the system board includes a floppy disk or CD th\
at provides a 
utility for transferring the service tag sequence to the replacement sys\
tem board.
NOTICE: If you received a flash BIOS update program floppy...

System Board: Dell Inspiron 8200
12.  If migrating the microprocessor, remove the microprocessor module. 
13.  Separate the network cable from the system board:  a.  First remove the network cable cover: Insert a narrow plastic scribe or \
small screwdriver just barely into the slot that faces the back of the 
computer (do not insert the scribe far enough to catch on the wires 
inside), press down on the cover lightly to secure it, and pry upward t\
o 
release the cover. 
 
1 network cable cover
b....