dell inspiron 8000 User Manual

Removing and Replacing Parts : Dell Inspiron 8100 
NOTICE: Be careful when handling the keyboard. The keycaps are fragile, 
easily dislodged, and time-consuming to replace. 
4.  Insert a pry stick under the blank key to pry up the keyboard. 
 
5.  Lift the right end of the keyboard, and slide it slightly to the rig\
ht to disengage  the tabs at the left end. 
6.  Pivot the keyboard and balance it upright on the left side of the co\
mputer. 
file:///F|/Service%20Manuals/Dell/Inspiron/8000/remove.htm (18...

Removing and Replacing Parts : Dell Inspiron 8100 
 
7.  Disconnect the keyboard cable and lay the keyboard assembly aside. 
Replacing the Keyboard Assembly 
1.  While bracing the keyboard assembly upright on its left end, connect\
 the  keyboard cable to the interface connector on the system board. 
NOTICE: Position the keyboard/track stick flex cable so that it is not pinched 
when you replace the keyboard in the bottom case assembly. 
2.  Insert the metal tabs at the left end of the keyboard under the...

Removing and Replacing Parts : Dell Inspiron 8100 
3.  Check that the keyboard is correctly installed. The keys should be f\
lush with the left and right surfaces of the palm rest. 
4.  Reinstall the four screws in the holes labeled circle K. 
Display and Bezel Assembly
file:///F|/Service%20Manuals/Dell/Inspiron/8000/remove.htm (20 of 56) \
[2/28/2004 7:32:58 AM] 

Removing and Replacing Parts : Dell Inspiron 8100 
 
NOTICE: Disconnect the computer and attached devices from electrical outlets 
and remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
periodically touching an unpainted metal surface on the computer. 
Removing the Hinge Cover 
 
1.  Follow the instructions in 
Preparing to Work Inside the Computer. 
2.  Use a nonmarring tool to loosen the hinge cover at the back and at e\
ach side of  the...

Removing and Replacing Parts : Dell Inspiron 8100 
 
1.  Remove the 
hinge cover. 
2.  Remove the M2.5 x 6-mm screw that secures the flex cable to the stra\
in relief,  and then use the pull loop to remove the flex cable from the video card.\
 
file:///F|/Service%20Manuals/Dell/Inspiron/8000/remove.htm (22 of 56) \
[2/28/2004 7:32:58 AM] 

Removing and Replacing Parts : Dell Inspiron 8100 
 
NOTICE: When reconnecting the flex cable, press down on both ends of the 
connector, not in the middle. Pressing the middle of the connector can d\
amage 
fragile components. 
3.  Open the display and remove the two screws (marked with a circle D\
) that  secure the display assembly to the bottom case assembly. 
4.  With the display in an upright position, lift the display assembly f\
rom the bottom  case assembly. 
Display Assembly Bezel and Panel...

Removing and Replacing Parts : Dell Inspiron 8100 
 
NOTICE: Disconnect the computer and attached devices from electrical outlets 
and remove any installed batteries. 
file:///F|/Service%20Manuals/Dell/Inspiron/8000/remove.htm (24 of 56) \
[2/28/2004 7:32:58 AM] 

Removing and Replacing Parts : Dell Inspiron 8100 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
periodically touching an unpainted metal surface on the computer. 
Removing the Display Assembly Bezel 
1.  Follow the instructions in Preparing to Work Inside the Computer. 
2.  Use a scribe to pry loose the four rubber screw covers located acros\
s the top of  the bezel. 
HINT: The 14.1-inch display panel has two M2.5 x 4-mm screws at the top of 
the bezel and two at the...

Removing and Replacing Parts : Dell Inspiron 8100 
 
NOTICE: When reconnecting the flex cable, press down on both ends of the 
connector, not in the middle. Pressing the middle of the connector can d\
amage 
fragile components. 
3.  Remove the 
display assembly bezel. 
4.  Remove the M2.5 x 4-mm screw securing the plastic flex-cable mountin\
g  bracket to the top cover assembly. 
5.  Remove the six M2 x 3-mm screws (three on each side) from the righ\
t and left  sides of the panel. 
6.  Lift the display...

Removing and Replacing Parts : Dell Inspiron 8100 
 
Replacing the Display Panel 
HINT: Use a magnetic screwdriver to reassemble the display panel in the 
display. 
1.  Connect the flex cable to the two connectors on the back of the disp\
lay panel. 
2.  Place the display panel assembly in the top cover, taking care that \
the flex cable  is in place and is not crushed or crimped. 
file:///F|/Service%20Manuals/Dell/Inspiron/8000/remove.htm (27 of 56) \
[2/28/2004 7:32:58 AM]