dell inspiron 8000 User Manual

Ports and Connector Pin-Outs : Dell Inspiron 8000 
18 QPCIEN#  68 +12V  118 SPERR#  168 SAD12 
19  S1.6M_EN#  69 AFD#  119 SLOCK#  169 GND 
20  DFDD/LPT#  70 ERROR#  120 SSTOP#  170 SAD13 
21  GND  71 ACK#  121 GND  171 SAD14 
22  NC  72 GND  122 SDEVSEL#  172 SAD15 
23  NC  73 INIT#  123 STRDY#  173 SAD16 
24  D_ATCTLED  74 SLCT_IN#  124 SIRDY#  174 SC/BE1# 
25  D_PWRLED  75 BUSY  125 SFRAME#  175 CD/BE2# 
26  DOCK_PWR_SRC  76 PE  126 SCLKRUN#  176 GND 
27  DOCK_PWR_SRC  77 SLCT  127 GND  177 SAD17 
28...

Ports and Connector Pin-Outs : Dell Inspiron 8000 
45 DOCK_+DC_IN  95 RXD0#  145 SRDATA#  195 GND 
46  DOCK_+DC_IN  96 DCD0  146 SINDEX#  196 NC 
47  DOCK_+DC_IN  97 NC  147 GND  197 NC 
48  DOCK_+DC_IN  98 +5VSUS  148 NC  198 NC 
49  GND  99 NC  149 +5VALW  199 NC 
50 LOW_PWR 100NC 150NC 200GND
IEEE-1394 Connector
 
Pin Signal
1 TPB– 
2 TPB+ 
3  TPA– 
4  TPA+ 
Back to Contents Page
file:///F|/Service%20Manuals/Dell/Inspiron/8000/pinouts.htm (9 of 10) \
[2/28/2004 7:32:51 AM] 

Ports and Connector Pin-Outs : Dell Inspiron 8000 
 
 
 
file:///F|/Service%20Manuals/Dell/Inspiron/8000/pinouts.htm (10 of 10)\
 [2/28/2004 7:32:51 AM] 

Removing and Replacing Parts : Dell Inspiron 8100 
Back to Contents Page 
Removing and Replacing Parts 
Dell™ Inspiron™ 8000 
  Preparing to Work Inside the 
Computer
  Recommended Tools
  Screw Identification
  System Components
  Hard Drive
  Fixed Optical Drive 
  Media Bay Devices
  Memory Modules
  Mini PCI Card Assembly
  Keyboard Assembly
  Display and Bezel Assembly
  Display Assembly Bezel and 
Panel
  Display Latch Assembly
  Microprocessor Thermal 
Cooling Assembly
  Microprocessor Module...

Removing and Replacing Parts : Dell Inspiron 8100 
1.  Make sure that the work surface is clean to prevent scratching the c\
omputer cover. 
2.  Save and close any open files, and exit any open programs. 
HINT: Make sure the computer is turned off and not in standby or hibernate 
mode. If you cannot shut down the computer using the computers operatin\
g 
system, press and hold the power button for 4 seconds. 
3.  Turn off the computer and all attached devices. 
4.  Make sure the computer is undocked. 
5....

Removing and Replacing Parts : Dell Inspiron 8100 
Recommended Tools
l     Number 1 magnetized Phillips screwdriver 
l     Small flat-blade screwdriver 
l     Pry stick 
l     Small plastic scribe 
l     Microprocessor extractor 
l     Flash BIOS update program floppy disk or CD (required only when upgradi\
ng the 
microprocessor, replacing the reserve battery, or replacing the system b\
oard). 
NOTICE: If the computer is running Microsoft® Windows® Millennium Edition \
(Me), you need to download the...

Removing and Replacing Parts : Dell Inspiron 8100 
 
NOTICE: When reinstalling a screw, you must use a screw of the correct 
diameter and length. Make sure that the screw is properly aligned with i\
ts 
corresponding hole, and avoid over tightening. 
Screw Placemat 
Hard Drive Door 
Security:M3 x 5 mm (1 
each)
 Keyboard to Bottom 
Case Assembly:M2.5 x 
20 mm (4 each; plus 
one in memory module 
cover and one in Mini 
PCI card cover)
 Display to 
Base:M2.5 x 6 
mm (3 each; 2 
at back of 
computer; 1 at...

Removing and Replacing Parts : Dell Inspiron 8100 
Display Bezel:Rubber 
screw covers (4 
each)Plastic screw 
covers (2 each)M2.5 x 4 
mm (6 each)
 Display Panel to 
Display Mounting 
Bracket:M2 x 3 mm (6 
each)
 
Flex-Cable Mounting 
Bracket to Top 
Cover:M2.5 x 4 mm (1 
each)
  Video 
Card:M2.5 x 8 
mm (3 each)
 
Palm Rest to
Bottom Case 
Assembly:M2.5 x 20 
mm (9 each)
 
Palm Rest Bracket:
M2.5 x 4 mm (2 each)
  System Board:M2.5 x 
4 mm captive washer 
(3 each)
 
M2.5 x 20 mm (1 each)
  LED Board:M2...

Removing and Replacing Parts : Dell Inspiron 8100 
 
file:///F|/Service%20Manuals/Dell/Inspiron/8000/remove.htm (6 of 56) [\
2/28/2004 7:32:58 AM] 

Removing and Replacing Parts : Dell Inspiron 8100 
Hard Drive
 
NOTICE: Disconnect the computer and attached devices from electrical outlets 
and remove any installed batteries. 
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
periodically touching an unpainted metal surface on the computer. 
Removing the Hard Drive 
NOTICE: To avoid damaging the system board, you must remove the main 
battery before you service the computer. 
NOTICE: Make sure that the work surface is clean...