Dell G2410 Users Guide

  
Back  
Press   to go back to the main menu.
  
Horizontal Po
sition   Use the   and   buttons to adjust image left and right. Minimum is 0 ( - ). Maximum is 100 (+).  
NOTE:   When using a DVI source, the Horizontal Position setting is not available.  
  
Vertical Posit
ion   Use the   and   buttons to adjust image up and down. Minimum is 0 ( - ). Maximum is 100 (+).  
NOTE:   When using a DVI source, the Vertical Position setting is not available.  
  
Sharpness  
This feature can make the image look...

  
  
   
 
  
Back  
Press   to go back to the main menu.
  
Language   Language option to set the OSD display to one of seven languages (English, Espanol, Francais, Deutsch, Brazilian Portuguese, Japanese, or Simplified 
Chinese).
Menu 
Transparency   This function is used to change the OSD background from opaque to transparent.  
  
Menu Timer   OSD Hold Time: Sets the length of time the OSD will remain active after the last time you pressed a button.  
Use the   and    buttons to adjust the slider in...

  
LCD 
Conditioning This feature will help reduce minor cases of image retention.  
 
If an image appears to be stuck on the monitor, select  LCD Conditioning  to help eliminate any image retention. Using the LCD Conditioning feature may take 
some time. LCD Conditioning feature cannot remove  severe cases of image retention or burn - in.
   
The below warning message appears once user selects  “ Enable LCD Conditioning.  
 
    NOTE:   Use LCD Conditioning only when you experience a problem with image...

Personalize
   
   

Back to Contents Page   
Setting Up Your Monitor   
 
Setting the display resolution to 1920 X 1080 (maximum)  
For maximum display performance while using the Microsoft ®
  Windows ®
  operating systems, set the display resolution to 1920 X 1080 pixels by performing the 
following steps:  
In Windows XP ®
:  
1. Right - click on the desktop and click  Properties .  
2. Select the  Settings  tab.  
3. Move the slider - bar to the right by pressing and holding the left - mouse button and adjust the screen...

 
Information in this document is subject to change without notice.  
 
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.   is strictly forbidden.  
Trademarks used in this text:  DELL  and the  DELL  log o  are trademarks of Dell Inc;  Microsoft  and  Windows  are either trademarks or registered trademarks of Microsoft Corporation in 
the United States and/or other countries;  Adobe  is a trademark of Adobe Systems Incorporated, which may be registered...

Back to Contents Page    
 
Setting Up the Monitor   
 
   Attaching the Stand  
   Connecting the Monitor  
   Organizing the Cables  
   Attaching the Soundbar (Optional)  
   Removing the Stand    
   Wall Mounting (Optional)    
Attaching the Stand  
Remove the monitor cover and place the monitor on it.  
1. Fit the two tabs on the upper part of the stand to the groove on the back of the monitor.   
2. Lower the stand so that the monitor mounting area snaps onto the stand.    
Connecting Your Monitor...

 
   
Organizing the Cables  
 
After attaching all necessary cables to your monitor and computer, (See  Connecting Your Monitor  for cable attachment,) use the cable management slot 
to organize all cables as shown above.  
Attaching the Soundbar (Optional)  
 CAUTION:  The graphics are used for the purpose of illustration only. Appearance of the computer may vary.  

 
Removing the Stand  
To remove the stand:  
1. P ress and hold the stand release button.    
2. Lift the stand up and away from the monitor .   
Wall Mounting (Optional)  NOTICE:  Do not use with any device other than Dell Soundbar. 
1. Working from the rear of the monitor, attach the Dell Soundbar by aligning the two slots with the two tabs along the bottom rear of the monitor.
2.   Slide the Dell Soundbar to the left until it snaps into place.
Connect the Soundbar with the power brick.
Plug the power...

 
(Screw dimension: M4 x 10 mm).   
Refer to the instructions that come with the VESA - compatible  base mounting kit.   
1. Place the monitor panel on a soft cloth or cushion on stable flat table.    
2. Remove the stand.    
3. Use a screwdriver to remove the four screws securing the plastic cover.    
4. Attach the mounting bracket from the wall mounting kit to the LCD.    
5. Mount the LCD on the wall by following the instructions that came with the base mounting kit.    
Back to Contents Page...