Dell E198wfp Users Guide

Dell™ E198WFP Flat Panel Monitor Users Guide
About Your Monitor
Front View
Back View
Side  View
Bottom View
Monitor Specifications
LCD  Monitor Quality & Pixel  Policy
Caring  for your  Monitor
Using Your Adjustable Monitor Stand
Attaching  the Stand
Organizing Your  Cables
Using the Tilt
Removing the Stand
Setting Up Your Monitor
Connecting Your  Monitor
Using the Front Panel
Using the OSD
Setting  the Optimal  Resolution
Using the Dell Soundbar (Optional)
 
 
Solving Problems
Troubleshooting Your...

Back to  Contents Page
About Your Monitor
Dell™ E198WFP  Flat Panel Monitor  Users Guide
  Front View
  Back View
  Side  View
  Bottom View
  Monitor Specifications
  LCD  Monitor Quality & Pixel  Policy
  Caring  for your  Monitor
Front View
1. Input signal  select  button
2. OSD menu  / Select button
3. Brightness and  Contrast  / Down button
4. Auto-adjust  / Up  button
5. Power On  / Off button (with LED indicator)
Back View
 

 
1VESA  mounting  holes (100mm)  (Behind
attached  base  plate) Use  to  mount the monitor.
2 Barcode serial  number label Refer to  this label if you need  to  contact  Dell for technical  support.
3 Security lock slot Use  a  security lock with the slot to  help secure your  monitor.
4 Stand  removal button Press  to  release  the stand.
5 Regulatory  rating label List the regulatory  approvals.
6 Dell Soundbar mounting  brackets Attach the optional  Dell Soundbar.
7 Cable management hole Help...

Left  side Right side  
Monitor Specifications
Power Management Modes
If  you have  VESAs DPM™  compliance display  card  or software installed  in your  PC, the monitor automatically reduces its  power consumption  when  not in use.  This is referred
to  as Power Save Mode. The  monitor automatically resumes  functioning when  the system  detects input from  the keyboard,  mouse or other input devices.The  following table
shows  the power consumption  and  signaling of this automatic power saving...

15-pin  D-Sub connector
Pin NumberMonitor Side of  the 15 -pin  Side Signal Cable
1 Video-Red
2 Video-Green
3 Video-Blue
4 GND
5 Self-test
6 GND-R
7 GND-G
8 GND-B
9 DDC +5V
10 GND-sync
11 GND
12 DDC data
13 H -sync
14 V -sync
15 DDC clock
24-pin  Digital-only DVI Connector
Note: Pin  1 is at the top right.
Pin Signal  Assignment PinSignal  Assignment PinSignal  Assignment
1 T.M.D.S. Data 2- 9T.M.D.S. Data 1- 17T.M.D.S. Data 0-
2 T.M.D.S. Data 2+ 10T.M.D.S. Data 1+ 18T.M.D.S. Data 0+
3 T.M.D.S. Data 2...

General
Model  numberE198WFP
Flat Panel 
Screen type Active matrix  - TFT LCD
Screen dimensions 19  inches  wide(19-inch wide viewable image size)
Preset display  area:  
Horizontal 408mm  / 16.1inches
Vertical 255mm  / 10.0  inches
Pixel  pitch 0.2835mm
Viewing angle 160° (vertical)  typ, 160° (horizontal) typ
Luminance  output 300 CD/m ²(typ)
Contrast  ratio 1000  to  1 (typ)
Faceplate  coating Antiglare  with hard-coating 3H
Backlight CCFL  (4) edgelight system
Response Time 5ms typical
Resolution...

Electrical
The  following table lists the monitor electrical features:
Video input signals Analog  RGB,  0.7 Volts +/ -5%, positive polarity at 75  ohm input impedance
Digital DVI-D  TMDS,  600mV for each  differential line, positive polarity at 50  ohm input impedance
Synchronization input signals Separate  horizontal and  vertical  synchronizations,  polarity-free TTL level,  SOG (Composite SYNC on
green)
AC input voltage  / frequency / current 100 to  240 VAC / 50  or 60  Hz  +
 3 Hz  / 2.0A (Max.)...

Caring for your Monitor
CAUTION: Read and follow the safety instructions before cleaning the monitor. 
CAUTION: Before  cleaning the monitor, unplug the monitor  power  cable from the electrical outlet.  
To clean your  antistatic  screen, slightly  dampen a  soft, clean cloth  with water. If  possible, use a  special screen-cleaning tissue  or solution  suitable for the antistatic
coating.  Do not use benzene, thinner, ammonia,  abrasive cleaners, or compressed  air.
Use  a  slightly  dampened, warm...

Back to  Contents Page
Using Your Adjustable Monitor Stand
Dell™ E198WFP  Flat Panel Monitor  Users Guide
  Attaching  the Stand
   Organizing Your  Cables
  Using the Tilt
  Removing the Stand 
Attaching the Stand
NOTE:  The  stand  is detached  when  the monitor is shipped from  the factory.
1. Place  the stand  on a  flat surface.
2. Fit the groove on the back  of the monitor onto the two tabs on the stand.
3. Lower  the monitor so that  the monitor mounting  area snaps on/locks to  the stand....

After attaching  all necessary  cables to  your  monitor and  computer, (See Connecting  Your  Monitor for cable  attachment,) use
the cable  hole  to  neatly  organize all cables as shown above.
Using the Tilt
You  can  tilt  the monitor to  best fit  your  viewing needs.
 
Removing the Stand