Dell E198wfp Users Guide
Have a look at the manual Dell E198wfp Users Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 327 Dell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Dell™ E198WFP Flat Panel Monitor Users Guide About Your Monitor Front View Back View Side View Bottom View Monitor Specifications LCD Monitor Quality & Pixel Policy Caring for your Monitor Using Your Adjustable Monitor Stand Attaching the Stand Organizing Your Cables Using the Tilt Removing the Stand Setting Up Your Monitor Connecting Your Monitor Using the Front Panel Using the OSD Setting the Optimal Resolution Using the Dell Soundbar (Optional) Solving Problems Troubleshooting Your Monitor General Problems Product Specific Problems Troubleshooting Your Soundbar Appendix FCC Identification Information Safety Information Contacting Dell Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. Information in this document is subject to change without notice. © 2007 -2008 Dell Inc. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell , the DELL logo, Inspiron , Dell Precision , Dimension , OptiPlex , Latitude, PowerEdge, PowerVault, PowerApp, and Dell OpenManage are trademarks of Dell Inc; Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation; Adobe is a trademark of Adobe Systems Incorporated, which may be registered in certain jurisdictions. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own. Model E198WFP January 2008 Rev. A03
Back to Contents Page About Your Monitor Dell™ E198WFP Flat Panel Monitor Users Guide Front View Back View Side View Bottom View Monitor Specifications LCD Monitor Quality & Pixel Policy Caring for your Monitor Front View 1. Input signal select button 2. OSD menu / Select button 3. Brightness and Contrast / Down button 4. Auto-adjust / Up button 5. Power On / Off button (with LED indicator) Back View
1VESA mounting holes (100mm) (Behind attached base plate) Use to mount the monitor. 2 Barcode serial number label Refer to this label if you need to contact Dell for technical support. 3 Security lock slot Use a security lock with the slot to help secure your monitor. 4 Stand removal button Press to release the stand. 5 Regulatory rating label List the regulatory approvals. 6 Dell Soundbar mounting brackets Attach the optional Dell Soundbar. 7 Cable management hole Help organize cables by placing them in the hole. Bottom View 1Power connector Insert the power cable. 2 Stand anti-theft feature Mount a 3*8 screw to make the stand undetachable. 3 DVI connector Connect your computer DVI cable. 4 VGA connector Connect your computer VGA cable. Side View
Left side Right side Monitor Specifications Power Management Modes If you have VESAs DPM™ compliance display card or software installed in your PC, the monitor automatically reduces its power consumption when not in use. This is referred to as Power Save Mode. The monitor automatically resumes functioning when the system detects input from the keyboard, mouse or other input devices.The following table shows the power consumption and signaling of this automatic power saving feature: VESA Modes Horizontal SyncVertical SyncVideoPower Indicator Power Consumption Normal operation ActiveActiveActiveGreen 38 W (typical) Active-off mode InactiveInactiveBlankedAmbers Less than 2 W Switch off ---Off Less than 1 W NOTE: The OSD only functions in the normal operation mode. One of the following messages appears when the Menu or Plus buttons are pressed when in Active-off mode. 1 : Auto Detect (Analog Input)In Power Save Mode Press computer power button or any key on keyboard or move mouse or 1 : Auto Detect (Digital Input) In Power Save Mode Press computer power button or any key on keyboard or move mouse 2: Analog Input In Power Save Mode Press computer power button or any key on keyboard or move mouse or 3: Digital Input In Power Save Mode Press computer power button or any key on keyboard or move mouse Activate the computer and the monitor to gain access to the OSD . This monitor is ENERGY STAR ®-compliant as well as TCO 99/03 power management compatible. * Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor. Pin Assignments
15-pin D-Sub connector Pin NumberMonitor Side of the 15 -pin Side Signal Cable 1 Video-Red 2 Video-Green 3 Video-Blue 4 GND 5 Self-test 6 GND-R 7 GND-G 8 GND-B 9 DDC +5V 10 GND-sync 11 GND 12 DDC data 13 H -sync 14 V -sync 15 DDC clock 24-pin Digital-only DVI Connector Note: Pin 1 is at the top right. Pin Signal Assignment PinSignal Assignment PinSignal Assignment 1 T.M.D.S. Data 2- 9T.M.D.S. Data 1- 17T.M.D.S. Data 0- 2 T.M.D.S. Data 2+ 10T.M.D.S. Data 1+ 18T.M.D.S. Data 0+ 3 T.M.D.S. Data 2 Shield 11T.M.D.S. Data 1 Shield 19T.M.D.S. Data 0 Shield 4 No Pin 12No Pin 20No Pin 5 No Pin 13No Pin 21No Pin 6 DDC Clock 14+5V Power 22T.M.D.S. Clock Shield 7 DDC Data 15Ground (for +5V) 23T.M.D.S. Clock + 8 No Connect 16Hot Plug Detect 24T.M.D.S. Clock - Plug and Play Capability You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer with its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so that the system can configure itself and optimize the monitor settings. Most monitor installations are automatic. You can select different settings if required.
General Model numberE198WFP Flat Panel Screen type Active matrix - TFT LCD Screen dimensions 19 inches wide(19-inch wide viewable image size) Preset display area: Horizontal 408mm / 16.1inches Vertical 255mm / 10.0 inches Pixel pitch 0.2835mm Viewing angle 160° (vertical) typ, 160° (horizontal) typ Luminance output 300 CD/m ²(typ) Contrast ratio 1000 to 1 (typ) Faceplate coating Antiglare with hard-coating 3H Backlight CCFL (4) edgelight system Response Time 5ms typical Resolution Horizontal scan range 30 kHz to 83 kHz (automatic) Vertical scan range 56 Hz to 75 Hz (automatic) Optimal preset resolution 1440 x 900 at 60 Hz Highest preset resolution 1440 x 900 at 60 Hz Video Supported Modes Video display capabilities (DVI playback) 480i/480p/576i/576p/720p/1080i/1080p (Supports HDCP) Preset Display Modes The following table lists the preset modes for which Dell guarantees image size and centering: Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz)Pixel Clock (MHz) Sync Polarity (Horizontal/Vertical) VESA, 720 x 400 31.570.028.3 -/+ VESA, 640 x 480 31.560.025.2 -/- VESA, 640 x 480 37.575.031.5 -/- VESA, 800 x 600 37.960.349.5 +/+ VESA, 800 x 600 46.975.049.5 +/+ VESA, 1024 x 768 48.460.065.0 -/- VESA, 1024 x 768 60.075.078.8 +/+ VESA, 1152 x 864 67.575.0108+/+ VESA, 1280 x 1024 64.060.0135.0 +/+ VESA, 1280 x 1024 80.075.0135.0 +/+ VESA, 1440 x 900 55.960.0106.5 -/+
Electrical The following table lists the monitor electrical features: Video input signals Analog RGB, 0.7 Volts +/ -5%, positive polarity at 75 ohm input impedance Digital DVI-D TMDS, 600mV for each differential line, positive polarity at 50 ohm input impedance Synchronization input signals Separate horizontal and vertical synchronizations, polarity-free TTL level, SOG (Composite SYNC on green) AC input voltage / frequency / current 100 to 240 VAC / 50 or 60 Hz + 3 Hz / 2.0A (Max.) Inrush current 120V:30A (Max.) 240V:60A (Max.) Physical Characteristics The following table lists the monitor physical characteristics: Connector type 15 -pin D -subminiature, blue connector; DVI-D, white connector Signal cable type Digital: Detachable, DVI-D, Solid pins, shipped detached from the monitor Analog: Detachable, D -Sub, 15pins, shipped attached to the monitor Dimensions (with stand) Height 14.38 inches (364.85 mm) Width 17.54 inches (445.09 mm) Depth 5.67 inches (143.90 mm) Dimensions: (without stand) Height 11.46 inches (291.19 mm) Width 17.54 inches (445.09 mm) Depth 2.32 inches (59.00 mm) Stand dimensions: Height 11.40 inches (289.25 mm) Width 11.52 inches (292.50 mm) Depth 5.67 inches (143.90 mm) Weight with packaging 14.26 lbs (6.47 kg) Weight with stand assembly and cables 10.58 lbs (4.8 kg) Weight without stand assembly (For wall mount or VESA mount considerations - no cables) 8.16 lbs (3.7 kg) Weight of stand assembly 2.14 lbs (0.97 kg) Environmental The following table lists the environmental condition for monitor: Temperature Operating 5° to 35°C (41° to 95°F) Nonoperating Storage: -20° to 60°C (-4° to 140°F) Shipping: -20° to 60°C(-4° to 140°F) Humidity Operating 10% to 80% (noncondensing) Nonoperating Storage: 5% to 90% (noncondensing) Shipping: 5% to 90%(noncondensing) Altitude Operating 3,657.6m (12,000 ft) max Nonoperating 12,192 m (40,000 ft) max Thermal dissipation 256.08 BTU/hour (maximum) 119.5 BTU/hour (typical) LCD Monitor Quality & Pixel Policy During the LCD Monitor manufacturing process, it is not uncommon for one or more pixels to become fixed in an unchanging state. The visible result is a fixed pixel that appears as an extremely tiny dark or bright discolored spot. In almost every case, these fixed pixels are hard to see and do not detract from display quality or usability. A display with 1 to 5 fixed pixels is considered normal and within competitive standards. For more information, see Dell Support site at: support.dell.com.
Caring for your Monitor CAUTION: Read and follow the safety instructions before cleaning the monitor. CAUTION: Before cleaning the monitor, unplug the monitor power cable from the electrical outlet. To clean your antistatic screen, slightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the antistatic coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air. Use a slightly dampened, warm cloth to clean the plastics. Avoid using detergent of any kind as some detergents leave a milky film on the plastics. If you notice a white powder when you unpack your monitor, wipe it off with a cloth. This white powder occurs during the shipping of the monitor.Handle your monitor with care as darker -colored monitor may scratch and show white scuff marks more than lighter-colored monitor. To help maintain the best image quality on your monitor, use a dynamically changing screen saver and power off your monitor when not in use. Back to Contents Page
Back to Contents Page Using Your Adjustable Monitor Stand Dell™ E198WFP Flat Panel Monitor Users Guide Attaching the Stand Organizing Your Cables Using the Tilt Removing the Stand Attaching the Stand NOTE: The stand is detached when the monitor is shipped from the factory. 1. Place the stand on a flat surface. 2. Fit the groove on the back of the monitor onto the two tabs on the stand. 3. Lower the monitor so that the monitor mounting area snaps on/locks to the stand. Organizing Your Cables
After attaching all necessary cables to your monitor and computer, (See Connecting Your Monitor for cable attachment,) use the cable hole to neatly organize all cables as shown above. Using the Tilt You can tilt the monitor to best fit your viewing needs. Removing the Stand