Dell Drac 5 User Manual

Using the DRAC 5 SM-CLP Command Line Interface231
RequestedStateIndicates the last requested or 
desired state for the system.
Values:
2=Enabled
3=Disabled
4=Shut Down
5=No Change
6=Offline
7=Test
8=Deferred
9=Quiesce
10=Reboot
11=Reset
12=Not Applicable
HealthStateIndicates the current health of 
the system.
Values:
0=Unknown
5=OK
10=Degraded/Warning
15=Minor Failure
20=Major Failure
30=Critical Failure
35=Non-recoverable Error Table 12-9. System Properties (continued)
Object Property Description 

232Using the DRAC 5 SM-CLP Command Line Interface
OperationalStatusIndicates the current status of 
the system.
Va l u e s :
0=Unknown
1=Other
2=OK
3=Degraded
4=Stressed
5=Predictive Failure
6=Error
7=Non-Recoverable Error
8=Starting
9=Stopping
10=Stopped
11=In Service
12=No Contact
13=Lost Communication
14=Aborted
15=Dormant
16=Supporting Entity in Error
17=Completed
18=Power Mode
DescriptionA text-based description of the 
system. Table 12-9. System Properties (continued)
Object Property Description 

Using the DRAC 5 SM-CLP Command Line Interface233
Property Names for Fan, Temperature, Numeric Voltage, Power 
Consumption, and Amperage Sensors
Supported Property Names for Fans, Temperature, Numeric Voltage, Power 
Consumption, and Amperage Sensors
Table 12-10. Sensors
Object Property Description
CIM_NumericSensorSystemCreationClass
NameThe name of the system 
creation class— 
CIM_ComputerSystem)
SystemNameThe service tag of the system, 
which is a unique identifier of 
a system that exists in the...

234Using the DRAC 5 SM-CLP Command Line Interface
BaseUnitsThe units of measurement of 
the sensor
RPM=Tachometer (for 
tachsensor)
C=Temperature (for 
tempsensor)
V=Voltage (for numericsensor) 
Watts=Power Consumption 
(for powerconsumption) 
Amp=Amperage (for 
amperage)
CurrentReadingThe current reading of the 
sensor.
LowerThresholdNonCr
iticalThe lower threshold non 
critical value
UpperThresholdNonCr
iticalThe upper threshold non 
critical value
LowerThresholdCriti
calThe lower threshold critical...

Using the DRAC 5 SM-CLP Command Line Interface235
SupportedThresholdThe supported threshold for 
the sensor.
{ LowerThresholdCritical } 
(for tachsensor) 
{ 
LowerThresholdNonCritical, 
UpperThresholdNonCritical,
UpperThresholdCritical, 
LowerThresholdCritical } 
(for tempsensor) 
{} (for voltsensor (numeric 
sensor))
{UpperThresholdNonCritical
, UpperThresholdCritical} 
(for powerconsumption
{} for amperage)
SettableThresholdThe threshold levels that you 
can set for a sensor.
{ } (no sensor support for...

236Using the DRAC 5 SM-CLP Command Line Interface
Property Names for Power Supply Sensors
CurrentStateThe current state as reported 
by a sensor
ElementNameThe name of the sensor
OtherSensorTypeDesc
riptionIf the sensortype property 
contains a value of 1 (others), 
this property gives additional 
description about that sensor.
Power consumption sensor. 
for powerconsumption
Amperage sensor. for 
amperage
EnabledStateIndicates if the sensor is 
enabled or disabled.
1=Enabled
Table 12-11. Supported...

Using the DRAC 5 SM-CLP Command Line Interface237
Property Names for Intrusion, Battery, Voltage, and Hardware 
Performance Sensors
TotalOutputPowerThe total power output as shown 
on the DRAC user interface
ElementNameName of the particular sensor.
OperationalStatusCurrent operational status of the 
power supply unit.
HealthStateThe health status of the power 
supply unit.
EnabledStateIndicates if the sensor is enabled 
or disabled
1=Enabled
Table 12-12. Supported Property Names for Intrusion, Battery,...

238Using the DRAC 5 SM-CLP Command Line Interface
DeviceIDUnique ID for the sensor in the 
system
Intrusion1…n (for intrusion 
sensor)
Battery1…n (for battery sensor)
Voltage1…n (for voltage sensor)
Hardware performance 
sensor1…n (for hardware 
performance sensor)
SensorType1=Other
3=Voltage (for voltage sensor)
PossibleStatesThe possible states for the sensor
{ no intrusion,chassis 
intrusion, drive bay intrusion, 
I/O card area intrusion, 
processor area intrusion, LAN 
disconnect, unauthorized 
dock,...

Using the DRAC 5 SM-CLP Command Line Interface239
Property Names for Fan and Power Supply Redundancy Set Sensors
OtherSensorTyp
eDescriptionIf the sensortype property 
contains a value of 1 (others), 
this property gives additional 
description about that sensor.
Chassis intrusion sensor (for 
Intrusion sensor)
CMOS battery sensor (for 
Battery sensor)
Hardware performance sensor 
(for Hardware Performance)
 EnabledStateIndicates if the sensor is enabled 
or disabled
1=Enabled (for all sensors)
Table...

240Using the DRAC 5 SM-CLP Command Line Interface
Property Names for Chassis Sensors
Property Names for Power Management Service
Table 12-14. Supported Property Names for Chassis Sensors
Object Property Description
CIM_ChassisCreationClassName The name of the creation 
class—CIM_Chassis
PackageType Type of package
3=Chassis
ChassisPackageType Chassis package type
17=Main system chassis
ManufacturerManufacturer
Dell
ModelThe model name of the 
system
ElementNameElement name
Table 12-15. Supported Property...