Dell 2407wfp Users Guide

   
   
   
See  Solving Problems  for more information.   
     
         
When the monitor does not support a particular resolution mode you will see the following 
message :
 
 
This means that the monitor cannot synchronize with the signal that it is receiving from the 
computer. See  Monitor Specifications  for the Horizontal and Vertical frequency ranges addressable 
by this monitor. Recommended mode is  1920 X 1200.  
 
You will see the following message before the DDC/CI function is disabled....

 
Soundbar Attachment to the Monitor  
 
Back to Contents Page  1. Attach mechanism 
2.   Headphone connectors 
Power indicator 
4.   Power/Volume control
NOTE: Soundbar Power Connector  -  12V DC output is for optional Dell™ Soundbar only. 
NOTICE:  Do not use with any device other than Dell Soundbar. 
1. Working from the rear of the monitor, attach Soundbar by aligning the two slots with the two tabs along the bottom rear of the monitor.
2.   Slide the Soundbar to the left until it snaps into place....

Back to Contents Page  
Solving Problems    
- HC Flat Panel Monitor   
   Monitor Specific Troubleshooting  
   Common Problems  
   Video Problems  
   Product Specific Problems  
   Universal Serial Bus (USB) Specific Problems  
   Dell™ Soundbar (Optionalyf7URXEOHVKRRWLQg  
   Card Reader Troubleshooting  
   
Troubleshooting   the   
Self - Test Feature Check  
Your monitor provides a self - test feature that allows you to check whether your monitor is functioning properly. If your monitor and...

   
Video Problems  Stuck - on Pixels LCD screen has 
bright spots l Cycle power on - off    
l These are pixels that are permanently on and is a natural defect that occurs in LCD technology    
Brightness Problems Picture too dim 
or too bright l Perform monitor reset on Factory Reset    
l Auto Adjust via OSD  
l Adjust brightness & contrast controls via OSD    
Geometric Distortion Screen not 
centered 
correctly l Perform monitor reset on Display Reset    
l Auto Adjust via OSD  
l Adjust brightness...

Product Specific Problems  
Universal Serial Bus (USB) Specific Problems  
   
 NOTE:  When choosing S - Video, Composite or Component video,  Auto Adjust  function is not available. 
SPECIFIC SYMPTOMS WHAT YOU EXPERIENCE POSSIBLE SOLUTIONS
Screen image is too small Image is centered on screen, but does not fill entire 
viewing area l Perform monitor reset on Factory Reset    
Cannot adjust the monitor with 
the buttons on the front panel OSD does not appear on the screen l Turn the monitor off and...

   
 
   
Back to Contents Page   l Decrease the volume of the audio application.   
l Turn the Power/Volume knob on the Soundbar counter - clockwise to a lower volume setting.   
l Clean and reseat the audio line - in plug.   
l Troubleshoot the computers sound card.   
l Test the Soundbar using another audio source (i.e. portable CD player).   
Distorted Sound Other audio source is used. l Clear any obstructions between the Soundbar and the user.   
l Confirm that the audio line - in plug is completely...

Back to Contents Page  
Using Your Adjustable Monitor Stand   
-  
   Attaching the Stand  
   Organizing Your Cables  
   Using the Tilt, Swivel and Vertical Extension  
   Removing the Stand   
   
Attaching the Stand  
 
1. Place the s tand  on a flat surface.  
2. Fit the groove on the back of the monitor onto the  2 tabs   of upper stand.   
3. Lower the monitor so that the monitor mounting area snaps on   or   locks to stand.   
Organizing Your Cables  
 
  
After attaching all necessary cables to...

 
 
Vertical Extension  
Stand extends vertically up to 100 mm via the Lock down / release button.                     
                  NOTE:   Stand is detached and extended when the monitor is shipped from the factory.  
NOTE:  If locked in the down position, push the monitor down. Press the Lock down / release button on the bottom rear of 
stand to unlock the monitor. Lift the monitor up and extend the stand to the desired height.     

                  
Removing the Stand  
  After placing the monitor panel on a soft cloth or cushion, press and hold the Monitor Lock / Release Button, and then remove the stand.   
 
   
Back to Contents Page  
    NOTICE:  Before relocating   or   moving the monitor to a different location, make sure that the stand is locked down. To lock it down, lower the height of 
the panel until it clicks and is locked into place.  
NOTE:   To prevent scratches on the LCD screen while removing the stand,   ensure...