DELL 2350dn User Manual

							From this menu: You can:
protected flash option is installed in the
device.
* Factory default setting
PCL Emul Mode
Mode Menu Mode Main Menu
PCL Emul Font Source
Font Name
Symbol Set
PCL Emulation Settings
Tray Renumber
From the menu list, use the Arrow buttons 
   to scroll to the PCL Emul menu.
1.
Press the  Select button 
.
2.
Press the  Right Arrow  button 
 until the heading you want appears on the display, and then press
the  Select  button 
.
3.
Use the  Arrow buttons 
   to scroll through the available menu items.
4.
When the setting you want appears on the display, press the  Select button 
 to save the setting.
5.
PCL Emul Mode Main Menu
From this
menu:
You can:
Font Source Specify the set of fonts used by the Font Name menu item.Resident*
All
Font Name Identify a specific font and the option where it is stored.Range: R0* – R90
Symbol Set Specify the symbol set for each font name.Default: 10U PC-8
PCL Emulation Settingsprotected flash option is installed in the
device.
* Factory default setting
PCL Emul Mode
Mode Menu Mode Main Menu
PCL Emul Font Source
Font Name
Symbol Set
PCL Emulation Settings
Tray Renumber
From the menu list, use the  Arrow buttons 
   to scroll to the PCL Emul menu.
1.
Press the  Select button 
.
2.
Press the  Right Arrow  button 
 until the heading you want appears on the display, and then press
the  Select  button 
.
3.
Use the  Arrow buttons 
   to scroll through the available menu items.
4.
When the setting you want appears on the display, press the  Select button 
 to save the setting.
5.
PCL Emul Mode Main Menu
From this
menu:
You can:
Font Source Specify the set of fonts used by the Font Name menu item.Resident*
All
Font Name Identify a specific font and the option where it is stored.Range: R0* – R90
*Factory
default
setting
  
						

							From this
menu:
You can:
Symbol Set Specify the symbol set for each font name.Default: 10U PC-8
PCL Emulation Settings
Point
Size
NOTE:  Only
for PostScript
emulation and
typographic
fonts.
Change the point size for scalable typographic fonts.1.00 – 1008.00 in increments of 0.25
12.00*
Pitch Assign the font pitch for scalable monospaced fonts.Range: 0.08 – 100.00 in increments of 0.01
10.00*
Orientation Specify the orientation of text and graphics on the page.Portrait*
Landscape
Lines per
Page
Assign the number of lines that print on each page.1–255
60*
A4 Width Set the printer to print on A4-size paper.198 mm*
203 mm
Auto CR
after LF
Specify whether the printer automatically performs a carriage return (CR)
after a line feed (LF) control command.
On
Off*
Auto LF
after CR
Specify whether the printer automatically performs a line feed (LF) after
a carriage return (CR) control command.
On
Off*
Tray Renumber
Assign
MP
Feeder
Assign Configure the printer to work with printer software or programs that use
different source assignments for trays, drawers, and feeders.
200 = Off*
Symbol Set Specify the symbol set for each font name.Default: 10U PC-8
PCL Emulation Settings
Point
Size
NOTE:  Only
for PostScript
emulation and
typographic
fonts.
Change the point size for scalable typographic fonts.1.00 – 1008.00 in increments of 0.25
12.00*
Pitch Assign the font pitch for scalable monospaced fonts.Range: 0.08 – 100.00 in increments of 0.01
10.00*
Orientation Specify the orientation of text and graphics on the page.Portrait*
Landscape
Lines per
Page
Assign the number of lines that print on each page.1–255
60*
A4 Width Set the printer to print on A4-size paper.198 mm*
203 mm
Auto CR
after LF
Specify whether the printer automatically performs a carriage return (CR)
after a line feed (LF) control command.
On
Off*
Auto LF
after CR
Specify whether the printer automatically performs a line feed (LF) after
a carriage return (CR) control command.
On
Off*
Tray Renumber
Assign
MP
Feeder
Assign Configure the printer to work with printer software or programs that use
different source assignments for trays, drawers, and feeders.
200 = Off*
*Factory
default
setting
  
						

							From this
menu:
You can:
Assign
Tray 
Assign
Manual
Paper
Assign
Man Env
0–199
View
Factory
Def
Display the factory default setting assigned to each tray, drawer, or
feeder.
Restore
Defaults
Return all tray, drawer, and feeder assignments to the factory default
settings.
*Factory
default
setting
 Assign
Tray 
Assign
Manual
Paper
Assign
Man Env
0–199
View
Factory
Def
Display the factory default setting assigned to each tray, drawer, or
feeder.
Restore
Defaults
Return all tray, drawer, and feeder assignments to the factory default
settings.
*Factory
default
setting
  
						

							Installing Optional Hardware
  Installing the 550-Sheet Optional Drawer
  Installing an Optional Memory Card
Installing the 550-Sheet Optional Drawer
An optional drawer attaches under the printer. A drawer consists of two parts: a tray and a support unit.
Your printer supports one optional drawer that holds up to 550 sheets of paper.
CAUTION: If you are installing a drawer after setting up the printer, turn off the printer, and
unplug the power cable before continuing.
Turn the printer off.
1.
Unpack the drawer, and remove any packing material.
2.
Place the drawer in the location you have chosen for your printer.
NOTE: If you have optional memory to install, leave clearance on the right side of the printer.
3.Align the holes in the printer with the positioning posts on the drawer, and lower the printer into place.
4.
5. 
						

							Turn the printer back on.
5.
In Windows Vista  ®
 or later:
Click 
 Control Panel .
a.
Click  Hardware and Sound .
b.
Click  Printers .
c.
In Windows ®
 XP and 2000 :
Click  Start
 Control Panel .
a.
Double-click  Printers and Other Hardware .
b.
Double-click  Printers and Faxes .
c.
6.
Right-click your  Dell Laser Printer model  icon.
7.
Click  Properties .
8.
Click  Install Options .
9.
Click  Ask Printer .
10.
Click  OK.
11.
Click  OK, and then close the Printers folder.
12. 
						

							Installing an Optional Memory Card
The system board has one connector for an optional memory card. The printer can support up to 160 MB for
a non-network printer and 288 MB for a network printer. The printer memory can only be upgraded using
128 MB memory cards for both network and non-network printers. The network printer can also be upgraded
using 256 MB memory cards.
CAUTION: If you are installing a memory card after setting up the printer, turn off the
printer, and unplug the power cable before continuing.
Turn the printer off.
1.
Open the memory access door on the right side of the printer.
NOTICE: Do not remove the memory card or touch the printer near the area of the memory card
while actively reading, writing, or printing from these devices. Data corruption can occur.
2.Push open the latches on both ends of the memory connector.
NOTICE: Memory cards are easily damaged by static electricity. Touch a grounded metal surface
before you touch a memory card.
NOTE: Memory cards designed for other printers may not work with your printer.
3.Unpack the memory card.
Avoid touching the connection points along the edge of the card.
4.
Align the notches on the bottom of the card with the notches on the connector.
5. 
						

							5.
Push the memory card firmly into the connector until the latches on both ends of the connector  snap
into place.
It may require some force to fully seat the card.
6.
Ensure that each latch fits over the notch on each end of the card.
7.
Close the side cover.
8.
Turn the printer back on.
9.
In Windows Vista  ®
 or later:
Click 
 Control Panel .
a.
Click  Hardware and Sound .
b.
Click  Printers .
c.
In Windows ®
 XP and 2000 :
Click  Start
 Control Panel .
a.
Double-click  Printers and Other Hardware .
b.
Double-click  Printers and Faxes .
c.
10.
Right-click your  Dell Laser Printer model  icon.
11.
12. 
						

							11.
Click  Properties .
12.
Click  Install Options .
NOTE: Memory cards designed for other printers may not work with your printer.
13.Click  Ask Printer .
14.
Click  OK.
15.
Click  OK, and then close the Printers folder.
16. 
						

							Loading Paper
  Setting the Paper Size and Paper Type
  Loading the 250-Sheet Paper Tray
  Loading the 550-Sheet Paper Tray
  Using the Rear Exit
  Using the Multipurpose Feeder
  Linking and Unlinking Trays
Setting the Paper Size and Paper Type
NOTE: You must install the software for your printer before configuring the paper trays. For more
information, see  Setting up for Local Printing
 or  Setting up for Network Printing
.
Dell™ 2330d/2350d Laser Printer - Attached Locally to a
Computer
After you set the Paper Size and Paper Type to the correct settings for the size and type used in the trays,
then any trays containing the same size and type are automatically linked by the printer.
NOTE: If the size of the paper being loaded now is the same size as the previously loaded paper, do
not change the Paper Size setting.
Ensure that the printer is on and  Ready appears.
1.
From the operator panel, press the  Menu button 
 until  Paper Menu  appears.
2.
Press the  Select button 
.
3.
Press the  Arrow buttons 
   until  Size/Type  appears, and then press the  Select button 
.
Select Source  appears.
4.
5. 
						

							Press the Arrow buttons 
   until the correct source appears, and then press the  Select button 
.
Size  appears under the source name.
5.
Press the  Select button 
.
6.
Press the  Arrow buttons 
   until the correct size appears, and then press the  Select button 
.
Submitting Changes  appears, followed by  Size.
7.
Press the  Arrow buttons 
   until  Type appears, and then press the  Select button 
.
8.
Press the  Arrow buttons 
   until the correct type appears, and then press the  Select button 
.
Submitting Changes  appears, followed by  Type.
9.
Dell 2330dn/2350dn Laser Printer - Attached to a Network
Setting the paper size and type for the printer is done through the Dell Printer Configuration Web Tool.
NOTE: Configuring paper trays through the Dell Printer Configuration Web Tool is available only on the
Dell 2330dn/2350dn Laser Printer.
Type your network printers IP address in your Web browser.
NOTE: If you do not know your printers IP address, print a network setup page, which lists the
IP address. For more information see  Printing a Network Setup Page
.1.When the Printer Status page opens, select  Printer Settings in the left column.
2.
From the Printer Settings page, select  Paper Menu.
3.
Select  Paper Size .
4.
Select the paper size you have in each tray.
5.
Click  Submit .
6.
Select  Printer Settings  in the left column.
7.
8.