DELL 2350dn User Manual

							2.
Pull the toner cartridge assembly out of the printer by pulling on the toner cartridge handle.
NOTE: Do not press the button on the toner cartridge assembly.
3.Place the toner cartridge assembly on a flat, clean surface.
4.
Press the button on the base of the toner cartridge assembly, and then pull the toner cartridge up and
out using the handle.
5.Unpack the new imaging drum.
NOTICE: Do not leave the imaging drum exposed to direct light for an extended period of time.
Extended light exposure can cause print quality problems.
6.Install the toner cartridge by aligning the white rollers on the toner cartridge with the white arrows on
the tracks of the new imaging drum and pushing the toner cartridge in as far as it will go. The cartridge
7. 
						

							clicks into place when correctly installed.
7.
Install the toner cartridge assembly into the printer by aligning the blue arrows on the guides of the
toner cartridge with the blue arrows in the printer and pushing the toner cartridge assembly as far as it
will go.
8.Turn the printer back on.
9.
Press and hold the  Cancel button 
 until  Resetting PC Counter  appears on the operator panel
display.
NOTICE: Resetting the imaging drums counter without replacing the imaging drum may damage
your printer and void your warranty.
10.Close the front cover.
11.
Replacing the Toner Cartridge
You can determine approximately how much toner is left in your cartridge by printing the printer settings
configuration sheet. This helps you decide when you might need to order replacement supplies.
When the  Toner low  message appears, or when you experience faded print, remove the toner cartridge. 
						

							Firmly shake it side-to-side and front-to-back several times to redistribute the toner, and then reinsert it and
continue printing. Repeat this procedure multiple times until print remains faded. When the print remains
faded, replace the toner cartridge.
NOTE:  You can still print for a short time after the  Toner low message appears, but print quality
decreases as the toner level decreases.
NOTICE: When replacing a toner cartridge, do not leave the new cartridge exposed to direct light for
an extended period of time. Extended light exposure can cause print quality problems.
Turn the printer off.
1.
Open the front cover by pressing the button on the right side of the printer and lowering the cover.
2.Press the button on the base of the imaging drum and pull the toner cartridge assembly up and out
using the handle.
3.Unpack the new toner cartridge assembly.
4. 
						

							NOTICE: When replacing a toner cartridge assembly, do not leave the new cartridge exposed to
direct light for an extended period of time. Extended light exposure can cause print quality
problems.
Rotate the cartridge in all directions to distribute the toner.5.
Install the new toner cartridge assembly by aligning the white rollers on the toner cartridge with the
arrows on the tracks of the imaging drum kit and pushing the toner cartridge in as far as it will go. The
cartridge  clicks into place when correctly installed.
6.
Close the front cover.
7.
Cleaning the Exterior of the PrinterMake sure that the printer is turned off and unplugged from the wall outlet.
CAUTION: To avoid the risk of electric shock, unplug the power cord from the wall
outlet and disconnect all cables to the printer before proceeding.
1.Remove paper from the paper support and paper exit tray.
2.
3. 
						

							2.
Dampen a clean, lint-free cloth with water.
NOTICE: Do not use household cleaners or detergents, as they may damage the finish of the
printer.
3.
Wipe only the outside of the printer, making sure to remove any ink residue that has accumulated on
the paper exit tray.
NOTICE: Using a damp cloth to clean the interior may cause damage to your printer. Damage to
the printer caused by not following the correct instructions for cleaning will not be covered under
warranty.
4.Make sure the paper support and paper exit tray are dry before beginning a new print job.
5. 
						

							Administrative Support
  Using the Embedded Web Server
  Locking the Operator Panel Menus Using the Embedded Web Server
  Creating an Administrative Password
Using the Embedded Web Server
If the printer is installed on a network, the Embedded Web Server is available for a range of functions:
Configuring printer settings
Checking the status of the printer supplies
Configuring network settings
Creating a password for certain menus
Viewing reports
Restoring the factory default settings
Viewing the virtual display
To access the Embedded Web Server, type the printer IP address into the address field of your Web browser.
NOTE: If you do not know the IP address of the printer, print a network setup page and locate the IP
address in the TCP/IP section. For more information, see  Printing a Network Setup Page
.
Locking the Operator Panel Menus Using the Embedded 
						

							Web Server
You can use the operator panel lockout functionality to create a PIN and choose specific menus to lock. Each
time a locked menu is selected, the user will be prompted to enter the correct PIN. The PIN does not affect
access through the Embedded Web Server.
NOTE: Locking the printer operator panel will prevent a user from entering the printer operator panel
both remotely and at the printer.
To lock operator panel menus:Open a Web browser. In the address bar, type the IP address of the printer or print server to be
protected using the format:  http://ip_address/.
1.
Click  Configuration .
2.
Under  Security , choose the menus you want to protect.
3.
Create and re-enter the PIN.
NOTE: PINs must be 4 digits and numeric (0–9).
4.Click  Submit  to save the PIN.
To change the PIN, click  Reset Form.
5.
Creating an Administrative Password
Creating an administrative password allows a system support person to password-protect printer settings.
To prevent a user from changing a printer setting, the operator panel should be locked and an administrative
password should be set. For more information, see  Locking the Operator Panel Menus Using the Embedded
Web Server .
NOTE: When the administrative password is set, the web server will require the password to be
entered before the web server will allow the user to enter any link on the Printer Settings page, with
the exception of the report links.
Open a Web browser.
1.
In the address bar, type the network printer or print server IP address, and then press  Enter.
2.
3. 
						

							2.
Click  Configuration .
3.
Under Other Settings, click  Security.
4.
Assign password security for specific device settings.
5.
Create advanced or user password.
NOTE: Password range is 8–128 characters.
6.Click  Submit .
To reset the password, click  Reset Form or click the  Change/Remove Advanced Password  link.
7. 
						

							Troubleshooting Your Printer
Frequently Asked Questions (FAQ): Dell™ 2330d/dn and
2350d/dn Laser Printer Issues and Solutions Paper Problems
Setup Problems Printing Problems
Error Messages Print Quality Problems
General Guidelines for Selecting or Loading Print Media Frequently Asked Questions (FAQ): Mac OS ®
Features, Issues, and Solutions
Avoiding Jams and Misfeeds Calling for Service
Clearing Paper Jams
 
Frequently Asked Questions (FAQ): Dell™ 2330d/dn
and 2350d/dn Laser Printer Issues and Solutions
How do I install the Dell 2330d/dn and 2350d/dn Laser Printer driver and software in Windows ®
via USB or Parallel connection?
See Installing the Printer Drivers
.
NOTE: DO NOT connect the printer to the computer using a USB cable and turn on the printer
before trying to install the printer driver.
Why do I get garbled text printed out continuously?Try any of the following:
Check the USB cable connections between the computer and the printer.
1.
Try using a different USB cable, if available.
2.
Uninstall and reinstall the Dell 2330d/dn and 2350d/dn Laser Printer driver.
3. 
						

							NOTE: For the local Status Monitor Center to work properly, bidirectional communication
support must be in place so that the printer and computer can communicate. An exception
is added to the Windows Firewall to allow this communication.
If this does not resolve this issue, check the USB cable connection with the printer. If failure
persists, then changing the USB cable might help.
If the above steps do not resolve this issue, then try uninstalling and reinstalling the Dell
2330d/dn and 2350d/dn Laser Printer driver.
3.
How do I install the optional 550-sheet drawer (Tray 2)? See Installing the 550-Sheet Optional Drawer
.
Why can’t I choose the optional 550-sheet drawer (Tray 2) in the printer driver? See Installing the 550-Sheet Optional Drawer
.
How do I set up trays to print with legal-size paper? See Loading the 250-Sheet Paper Tray
 and  Loading the 550-Sheet Paper Tray
.
How do I install the Dell 2330d/dn and 2350d/dn Laser Printer driver through network for
Windows?
See Setting up for Network Printing
.
How do I reset the imaging drum counter? To reset the counter, press and hold the  Cancel button 
 until  Resetting PC Counter  appears on the
operator panel display. For more information, see  Replacing the Imaging Drum
.
NOTE: Resetting the imaging drum counter without replacing the imaging drum may damage
your printer and void your warranty.
NOTE: Use this setting to return the imaging drum counter to zero. The replace imaging drum
message will be cleared only when the imaging drum has been changed.
How do I reset factory defaults?See General Settings Mode
.
How do I find the printer IP and MAC address?