DELL 2330d User Manual

5.  From the Settings pop -up  menu,  choose  Page  Attributes.
6 .  From the Paper  Size pop -up  menu,  choose the custom paper size.
This newly added custom paper size is an available  option for all print  jobs, regardless of the selection in the
“Format for”  menu.  Another way  to  use custom paper for print  jobs  is to  choose the source that  contains  the
custom paper in the “All  pages from” pop -up  menu  on the Paper  Feed pane of the Print dialog.
Why are screen fonts provided ? PostScript...

Is  the printer cover closed properly ?
Try turning your  printer off and  back  on again.  If  your  printer is still not operating  properly, call  for service. If  you are able  to
print, press  the Menu  button 
 to  print  a  menu  settings page, which lists the printer model type and  other information  the
service  representative  may need  to  know.
For  more  information, contact  Dell at support.dell.com
.
 

Loading Paper
  Setting the Paper  Size and  Paper  Type
  Loading the 250-Sheet and  550-Sheet Paper  Trays
  Using the Rear Exit
  Using the Multipurpose  Feeder
  Linking and  Unlinking  Trays
Setting the Paper Size and Paper Type
Dell™ 2330d Laser Printer — Attached Locally to a Computer
After you set  the Paper  Size and  Paper  Type  to  the correct settings for the size and  type used in the trays, then  any trays
containing  the same  size and  type are automatically linked by the printer.
NOTE:...

Dell 2330dn Laser Printer — Attached to a Network
Setting  the paper size and  type for the printer is done through the Dell Printer  Configuration  Web Tool.
NOTE: Configuring paper trays through the Dell Printer  Configuration  Web Tool  is available  only  on the Dell 2330dn
Laser Printer.
1 .  Type  your  network printers IP  address in your  Web browser.
NOTE: If you do not know your  printers IP  address,  print  a  network setup  page, which lists the IP  address.  For
more  information  see...

c.  Move the rear paper guide to  the back  of the paper tray.
3 .  Flex a  stack of paper back  and  forth.  Straighten  the edges on a  level surface.
4 .  Load the paper in the tray  with the print  side  facing  down.
Ensure  that  the paper is below  the maximum  fill  line  on the side  paper guides. Overloading may cause paper jams.
 

5.  Slide the two side  guides  and  the rear guide until they rest  against the edges of the paper.
6.  Replace the tray.
7 .  Extend the paper support on the output bin.
Using the Rear Exit
The  single -sheet rear exit  provides  a  straight-through paper path  to  help reduce curling and  potential jams. This is especially
useful  for specialty media,  such as transparencies, envelopes, labels,  card  stock, or index cards.
To use the rear exit, open the rear exit  door. When  the rear exit  door  is...

Using the Multipurpose Feeder
Configuring the Multipurpose Feeder
This setting  is used to  designate  the mode of operation  for the multipurpose feeder.1.  From the operator  panel menu  list, use the  Arrow buttons 
  to  scroll the Paper  menu.
2 .  Press  the  Select button 
.
3 .  Press  the  Right Arrow  button 
 until the heading you want  appears on the display, and  then  press  the  Select button 
.
4 .  Use  the  Arrow buttons 
  to  scroll through the available  menu  items.
5 .  When  the...

2.  Slide the multipurpose feeder  tray  forward.
3 .  Pull the extension  so it  flips forward.
4 .  Guide the extension  down  gently  to  fully extend  the multipurpose feeder.
Loading the Multipurpose Feeder
To load  the multipurpose feeder:
1.  Place  a  sheet of the selected print  media,  print  side  facing  up, at the center of the multipurpose feeder, but only  to  the
point  where its  leading edge  can  contact  the paper guides. Otherwise, the printer engages  the print  media too  soon
and...

NOTE: Do not exceed  the maximum  stack height by forcing  paper or specialty media under the stack height
limiters which are located  on the guides.
2 .  Adjust  the paper guides  to  the print  medias  width.
3 .  Prepare the print  media for loading.
Flex sheets  of paper or paper labels back  and  forth to  loosen them, and  then  fan  them. Do not fold  or crease  the
paper or labels.  Straighten  the edges on a  level surface.
NOTE: Avoid  touching the print  side  of the transparencies. Be...

4.  Hold  both  sides of the print  media close  to  the multipurpose feeder, and  push it  into the printer until it  automatically
engages.
There is a  brief  pause between  the time the printer engages  the print  media and  when  it  feeds  into the printer.
Insert envelopes with the flap  side  facing  down  and  with the stamp  area as shown.
NOTE: For  best performance  do not use envelopes that  have  postage stamps attached.
Hold  transparencies by the edges, and  avoid  touching the print...