DELL 2330d User Manual

Network/Ports
Each Network  sub -menu  only  appears if the device has  a  standard  network card  or if additional network card  have  been
installed.
Use  the Network  menu  to  change  printer settings on jobs  sent through a  network port (either Standard  Network  or Network
Opt ).1.  From the menu  list, use the  Arrow buttons 
  to  scroll the Network  menu.
2 .  Press  the  Select button 
.
3 .  Press  the  Right Arrow  button 
 until the heading you want  appears on the display, and  then  press...

Use  the USB  menu  to  change  printer settings on jobs  sent through a  USB  port.1.  From the menu  list, use the  Arrow buttons 
  to  scroll the USB  menu.
2 .  Press  the  Select button 
.
3 .  Press  the  Right Arrow  button 
 until the heading you want  appears on the display, and  then  press  the  Select button 
.
4 .  Use  the  Arrow buttons 
  to  scroll through the available  menu  items.
5 .  When  the setting  you want  appears on the display, press  the  Select button 
 to  save the...

* Factory  default setting
On*
Off
PS
SmartSwitch Set  the printer to  automatically switch to  PostScript emulation when  a  print
job requires  it,  regardless of the default printer language.
On*
Off
NPA Mode Send print  jobs  to  the printer and  query printer status information  at the same  time.
Off
On
Auto*
USB  Buffer Assign  a  size to  the USB  input buffer.
Auto*
Disabled
3K to    (in  1K increments).
MAC Binary
PS Configure  the printer to  process Macintosh  binary PostScript emulation...

Use  the Parallel menu  to  change  printer settings on jobs  sent through a  parallel  port.1.  From the menu  list, use the  Arrow buttons 
  to  scroll the Parallel menu.
2 .  Press  the  Select button 
.
3 .  Press  the  Right Arrow  button 
 until the heading you want  appears on the display, and  then  press  the  Select button 
.
4 .  Use  the  Arrow buttons 
  to  scroll through the available  menu  items.
5 .  When  the setting  you want  appears on the display, press  the  Select button 
 to...

Settings
* Factory  default setting
Standard
Fastbytes*
Honor  Init Determine  whether  the printer honors  hardware initialization  requests from  the computer. The  computer  requests initialization  by activating the INIT signal  on the
parallel  interface.
Many  personal  computers activate the INIT signal  each  time the computer  is turned on
and  off.
On
Off*
Parallel
Mode  2 Determine  whether  the parallel  port data is sampled on the leading (on) or trailing
(off) edge  of the strobe.
Off
On*...

1.  From the menu  list, use the  Arrow buttons   to  scroll to  the General Settings menu.
2 .  Press  the  Select button 
.
3 .  Press  the  Right Arrow  button 
 until the heading you want  appears on the display, and  then  press  the  Select button 
.
4 .  Use  the  Arrow buttons 
  to  scroll through the available  menu  items.
5 .  When  the setting  you want  appears on the display, press  the  Select button 
 to  save the setting.
Run Initial Setup
Alarms
Timeouts
Print Recovery
Factory...

*Factory default setting
Toner Alarm
Off*
Single
Continuous
Timeouts Specify the number of minutes  of inactivity before the system  enters a
lower power state.
Power Saver Mode
Disabled
1–240  minutes
60  minutes*
Screen Timeout
15*–300 seconds
Print  Timeout
Disabled
1–255  seconds
90  seconds*
Wait Timeout
Disabled
15–65535  seconds
40  seconds*
Network  Job  Timeout
Disabled
10–255 seconds
90  seconds*
Print
Recovery Specify whether  the printer continues from  certain  offline  situations,
reprints...

1.  From the menu  list, use the  Arrow buttons   to  scroll to  the Setup  menu.
2 .  Press  the  Select button 
.
3 .  Press  the  Right Arrow  button 
 until the heading you want  appears on the display, and  then  press  the  Select button 
.
4 .  Use  the  Arrow buttons 
  to  scroll through the available  menu  items.
5 .  When  the setting  you want  appears on the display, press  the  Select button 
 to  save the setting.
Use  the Setup  menu  to  configure how the printer formats the end  of a...

The  finishing menu  specifies  the default finishing for all print  jobs.1.  From the menu  list, use the  Arrow buttons 
  to  scroll to  the Finishing  menu.
2 .  Press  the  Select button 
.
3 .  Press  the  Right Arrow  button 
 until the heading you want  appears on the display, and  then  press  the  Select button 
.
4 .  Use  the  Arrow buttons 
  to  scroll through the available  menu  items.
5 .  When  the setting  you want  appears on the display, press  the  Select button 
 to  save the...

* Factory  default setting
On—Prints  the entire  job the number of times  specified by the
Copies menu  item.  For  example, if you set  Copies to  2 and  send
three pages to  print, the printer prints page  1, page  2, page  3,
page  1, page  2, page  3.
Off*—Prints each  page  of a  job the number of times  specified by
the Copies menu  item.  For  example, if you set  Copies to  2 and
send three pages to  print, the printer prints page  1, page  1,
page  2, page  2, page  3, page  3.
Separator
Sheets...