DELL 2230d User Manual

Universal Setup menu
These menu items are used to specify the height, width, and feed direction of the Universal Paper Size. The Universal
Paper Size is a user-defined paper size. It is listed with the other paper size settings and includes similar options, such
as support for duplex printing and printing multiple pages on one sheet.
Menu itemDescription
Units of Measure
Inches
MillimetersIdentifies the units of measure
Notes:
Inches is the US factory default setting.
Millimeters is the international...

USB menu
Menu itemDescription
PCL SmartSwitch
On
OffSets the printer to automatically switch to PCL emulation when a print job received
through a USB port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PostScript emulation if the PS
Smartswitch setting is On. It uses the default printer language specified in the
Setup menu if the PS...

Parallel menu
Menu itemDescription
PCL SmartSwitch
On
OffSets the printer to automatically switch to PCL emulation when a print job received
through a parallel port requires it, regardless of the default printer language
Notes:
On is the factory default setting.
When the Off setting is used, the printer does not examine incoming data.
When the Off setting is used, the printer uses PostScript emulation if PS
SmartSwitch is set to On. It uses the default printer language specified in the
Setup menu if PS...

Menu itemDescription
Protocol
Standard
FastbytesSpecifies the parallel port protocol
Notes:
Fastbytes is the factory default setting. It provides compatibility with most
existing parallel ports and is the recommended setting.
The Standard setting tries to resolve parallel port communication problems.
Honor Init
On
OffDetermines whether the printer honors printer hardware initialization requests from
the computer
Notes:
Off is the factory default setting.
The computer requests initialization by activating...

Menu itemDescription
Alarm
Cartridge Alarm
Off
SingleThe display shows a message when the toner is low.
Notes:
Off is the factory default setting. The Toner is low
message will appear as a warning.
Single means the Toner is low message will appear and
the indicator light will blink red.
Timeouts
Power Saver
Disabled
1–240Sets the amount of time in minutes the printer waits after a job is
printed before it goes into a reduced power state
Notes:
60 minutes is the factory default setting.
Disabled does not...

Menu itemDescription
Print Recovery
Page Protect
On
OffLets the printer successfully print a page that may not have printed
otherwise
Notes:
Off is the factory default setting. Off prints a partial page when
there is not enough memory to print the whole page.
On sets the printer to process the whole page so that the entire
page prints.
Factory Defaults
Do Not Restore
Restore NowReturns the printer settings to the factory default settings
Notes:
Do Not Restore is the factory default setting. Do Not...

Menu itemDescription
Resource Save
On
OffSpecifies how the printer handles temporary downloads, such as
fonts and macros stored in RAM, when the printer receives a job
that requires more memory than is available
Notes:
Off is the factory default setting. Off sets the printer to retain
the downloads only until memory is needed. Downloads are
deleted to process print jobs.
The On setting retains the downloads during language
changes and printer resets. If the printer runs out of memory,
then downloads are...

Menu itemDescription
Collate
Off (1,1,1,2,2,2)
On (1,2,1,2,1,2)Stacks the pages of a print job in sequence when printing multiple copies
Notes:
On is the factory default setting, so the pages will be printed sequentially.
Both settings print the entire job the same number of times.
Separator Sheets
None
Between Copies
Between Jobs
Between PagesSpecifies whether blank separator sheets are inserted
Notes:
None is the factory default setting.
Between Copies inserts a blank sheet between each copy of a print...

Menu itemDescription
N-up Border
None
SolidPrints a border around each page image when using N-up (pages-sides)
Note: None is the factory default setting.
Quality menu
Menu itemDescription
Print Resolution
300 dpi
600 dpi
1200 dpi
1200 IQ
2400 IQSpecifies the printed output resolution
Note: 600 dpi is the factory default setting.
Toner Darkness
1–10Lightens or darkens the printed output
Notes:
8 is the factory default setting.
Selecting a smaller number can help conserve toner.
Enhance Fine Lines
On...

PostScript menu
Menu itemDescription
Print PS Error
On
OffPrints a page containing the PostScript error
Note: Off is the factory default setting.
Font Priority
Resident
Flash/DiskEstablishes the font search order
Notes:
Resident is the factory default setting.
A formatted flash memory option card must be installed in the printer and
operating properly for this menu item to be available.
The flash memory option cannot be Read/Write, Write, or
password-protected.
Job Buffer Size must not be set to 100%....