DELL 2130cn User Manual

   
   
3. Push the side button and open the front cover.   
 
   
   
4. Open the belt unit.   
 
   
   
5. Clean the CTD sensor inside the printer with a clean dry cotton swab.   
 
   
   
6. Close the belt unit by pushing it up.   
 
   
   
7. Close the front cover.   
 
   
     

8. Insert the standard 250 - sheet tray into the printer, and push until it stops.   
 
   
   
Adjusting Color Registration   
To adjust the color registration after moving it to a new location, follow the procedure below.  
   
Printing the Color Registration Chart   
   
When Using the Operator Panel   
   
1. Press  Menu  button.   
 
     
2. Press   button until  Admin Menu  appears, and then press    (Set)  button.   
 
     
3. Press   button until  Maintenance  appears, and then press    (Set)...

The following explains how to determine the adjustment values for the fast scan and the slow scan using Chart 1 and Chart 2.  
   
Fast Scan   
On the Chart 1 of the color registration chart, find the straightest lines where the two black lines and the colored line are most closely aligned for each color 
( Y ,  M , and  C ). If you find the straightest line, make a note of the value ( - 9   -   +9 ) indicated by the straightest line for each color.  
When the value is  0  for each color, you do not need...

   
   
Entering Values  
   
When Using the Operator Panel   
Using the operator panel, enter the values that you found in the color registration chart to make adjustments.   
   
1. Press  Menu  button.   
 
     
2. Press   button until  Admin Menu  appears, and then press    (Set)  button.   
 
     
3. Press   button until  Maintenance  appears, and then press    (Set)  button.   
 
     
4. Press   button until  Color Reg Adj  appears, and then press    (Set)  button.   
 
     
5. Press   button...

   
11. Press   or   button until you reach the value (for example, +3) displayed on the chart.   
 
     
12. Press   button once and move the cursor to the next value.   
 
     
13. Repeat steps 11 and 12 to enter all of the digits of the  Slow Scan , and then press    (Set)  button.   
 
     
14. Press  Cancel  button.   
 
     
15. Press   button until  ColorRegi Chart  appears, and then press    (Set)  button.   
 
The color registration chart is printed with the new values.  
   
16. Press...

Back to Contents Page    
 Removing Options   
   Removing the Optional 250 - Sheet Feeder   
   Removing a Duplexer   
   Removing a Memory   
   Removing the Network Protocol Adapter   
   Removing the Wireless Printer Adapter   
 
If the printer location needs to change or the printer and print media handling options need to be shipped to a new location, all print media handling options 
must be removed from the printer. For shipping, pack the printer and print media handling options securely to avoid...

5. Insert the standard 250 - sheet tray into the printer, and push until it stops.   
 
   
   
   
6. Reconnect all cables including the power cable into the back of the printer and turn on the printer.   
 
Removing a Duplexer   
   
1. Ensure that the printer is turned off.   
 
     
2. Push the side button and open the front cover.   
 
   
   
3. Hold the side button and release the lock of the duplexer by lifting the front edge of it slightly.   
 
   
   
4. Remove the duplexer from the printer...

Removing a Memory   
   
1. Ensure that the printer is turned off.   
 
     
2. Turn the screw on the control board cover in a counter - clockwise direction and open the cover.   
 
   
   
3. Remove the control board cover.   
 
   
   
4. Push the latches on both edges of the socket outward at the same time to raise the memory up.   
 
   
   
5. Hold the memory and pull it out.   
 
   
   
6. Install the control board cover.   
    NOTE:  Take off the below edge of the control board cover by turning...

   
   
7. Close the control board cover and turn the screw clockwise.   
 
   
Removing the Network Protocol Adapter   
   
1. Turn off the printer and unplug the power cable. Then, disconnect all cables from the back of the printer.   
 
     
2. Turn the screw on the control board cover in a counter - clockwise direction and open the cover.   
 
   
   
3. Remove the control board cover.   
 
   
   
4. Remove the network protocol adapter by releasing the adapters hooks.   
    NOTE:  Take off the...

   
   
5. Install the control board cover.   
 
   
   
6. Close the control board cover and turn the screw clockwise.   
 
   
   
7. Reconnect all cables including the power cable into the back of the printer and turn on the printer.   
 
Removing the Wireless Printer Adapter   
   
1. Turn off the printer and unplug the power cable. Then, disconnect all cables from the back of the printer.   
 
     
2. Turn the screw on the control board cover in a counter - clockwise direction and open the cover....